Safety Summary, Symbol Description | Agilent Technologies 5951-2826

SAFETY SUMMARY (continued)

GENERAL

Any LEDs used in this product are Class 1 LEDs as per IEC 825-l.

This ISM device complies with Canadian ICES-001. Cet appareil ISM est conforme à la norme NMB-001 du Canada.

ENVIRONMENTAL CONDITIONS

This instruments is intended for indoor use in an installation category II, pollution degree 2 environment. It is designed to operate at a maximum relative humidity of 95% and at altitudes of up to 2000 meters. Refer to the specifications tables for the ac mains voltage requirements and ambient operating temperature range.

SAFETY SYMBOL DEFINITIONS

Symbol

Description

Direct current

Alternating current

Both direct and alternating current

Three-phase alternating current

Earth (ground) terminal

Protective earth (ground) terminal

Frame or chassis terminal

Terminal for Neutral conductor on permanently installed equipment

Terminal is at earth potential(Used for measurement and control circuits designed to be operated with one terminal at earth potential.)

Symbol

Description

Terminal for Line conductor on permanently installed equipment

Caution, risk of electric shock

Caution, hot surface

Caution (refer to accompanying documents)

In position of a bi-stable push control

Out position of a bi-stable push control

On (supply)

Off (supply)

Standby (supply)

Units with this symbol are not completely disconnected from ac mains when this switch is off. To completely disconnect the unit from ac mains, either disconnect the power cord or have a qualified electrician install an external switch.

Herstellerbescheinigung

Diese Information steht im Zusammenhang mit den Anforderungen der Maschinenläminformationsverordnung vom 18 Januar 1991.

* Schalldruckpegel Lp <70 dB(A) * Am Arbeitsplatz * Normaler Betrieb * Nach EN 27779 (Typprufung).

Manufacturer’s Declaration

This statement is provided to comply with the requirements of the German Sound Emission Directive, from 18 January 1991.

* Sound Pressure Lp <70 dB(A) *At Operator Position * Normal Operation * According to EN 27779 (Type Test).

4

Image 4

Agilent Technologies 5951-2826 Safety Summary, Symbol Description, Herstellerbescheinigung, Manufacturer’s Declaration

Contents

Agilent Part No Microfiche Part No Updated April Operating Manual Certification Safety Summary Safety Summary Symbol DescriptionHerstellerbescheinigung Manufacturer’s Declaration Printing History Table of Contents Remote Operation Local OperationCalibration Considerations for Operating in Constant Resistance Mode What’s In This Manual Reader PathOptions General Information Safety Requirements Specifications Regulation Constant Resistance Mode Ranges Modes Continuous ModePulsed Mode 6060B 6063B Current Readback Resolution Supplemental Characteristics 6060B 6063BTemperature Coefficient Maximum Readback Capability Bandwidth Supplemental Characteristics Maximum VA Peak Inrush Current 2.5 a typicalCurrent Slew Rate Rate # High Range Step Low Range Step Transition Time Overshoot Resistance Slew RateModel 6063B Range Transient Current Level 6060B 6063B 10% With unit onWith unit off WidthPage Introduction Front Panel DescriptionRemote Programming Operation Overview Local/Remote Control Programmable FeaturesConstant Current CC Mode Modes of Operation Triggered Current Level Software Current Limit Slew Rate Constant Resistance CR ModeImmediate Resistance Level Triggered Resistance Level Constant Voltage CV ModeTransient Resistance Level Immediate Voltage Level Triggered Voltage LevelTransient Voltage Level Transient Operation Hpsl Command Description Pulsed Transient Operation Selects the external trigger input Selects pulsed transient operationSets pulse width to 1 millisecond Selects the external trigger input source Triggering a preset level Triggering a transient pulseToggling Slew Rate And Minimum Transition Time Input Current, Voltage, and Power Measurement Risetime Transition Limitation Short On/Off Transition Times and Slew Rates Saving and Recalling Settings Reading Remote Programming ErrorsInput On/Off Status Reporting Protection Features Resetting Latched ProtectionOvervoltage Overcurrent Control Connector OverpowerOvertemperature Reverse Voltage Monitor Outputs FaultExternal Programming Input Port On/Off Inspection Turn-On Checkout Location and CoolingCheck Line Voltage Voltage Select Switches Line Voltage Fuse Agilent Part No Connect The Power Cord Gpib Errors Input Errors Display DescriptionError Turn-On/Selftest Gpib Connector Power TestController Connection Rear Panel Connectors and Switches Wire Size Strip backGpib Address AWG Input Binding Post Control Connector Pins 3 +S and -SIM and VM Common Trigger Connector Sense Switch Application Connections Parallel Connections Maximum Wire Lengths to Limit Voltage DropsZero-Volt Loading Connections 11. Local Sensing 13. Parallel Operation Page Front Panel Controls and Indicators Description Local Operation Controls and Indicators Description Function Keys Local Control Overview ∙ Short on Using The Function KeysTurning the Input On/Off Recommended Programming Sequence Setting the Mode of Operation Setting CC ValuesCC Programming Ranges Function Key Display Examples Setting CR Values Examples Setting CV Values Continuous Pulse Train Programming Ranges Function Key Display Range of Values Using The System Keys Shorting The Input Setting The Electronic Load’s Gpib Address Displaying Error Codes Factory Default Settings Function 6060B 6063B Changing Wake-up Settings Recalling the Factory Default Values Enter/Output Statements Gpib AddressOutput Enter Sending a Remote Command Remote Programming CommandsGetting Data Back Output 705 MEASCURR? Modes RangesTransient levels Slew Rates Remote Programming Flowchart Sheet Remote Programming Flowchart Sheet CV Mode Example CC Mode ExampleCR Mode Example Continuous Transient Operation Example Pulsed Transient Operation Example Hpsl Command Short Form Output 705TRAN on Output 705INPUT onRemote Programming Ranges Function Constant Current CC Constant Resistance CR 6060BConstant Voltage CV Transient OperationPage Equipment Characteristics Recommended Model Example ProgramsEquipment Required Equipment Required for Calibration Calibration Commands Calibration Flowcharts Example Program Supply Shunt Values Settings Calibration Information 6060B 6063B Calibration Flowchart Calibration Flowchart Calibration Flowchart Program Listing PauseWait END if Pause Subend Print Voltage Calibration Else Explanation LinePage Considerations For Operating In Constant Resistance Mode Considerations For Operating In Constant Resistance Mode Considerations For Operating In Constant Resistance Mode Index Index Index 24, 25, 26 Index Agilent Sales and Support Offices Agilent Sales and Support Office Manual Updates