Agilent Technologies 5951-2827, 5951-2826 instruction

3.Hand tighten the adjustment knob to secure the wire in the binding post. If you are using a slotted screwdriver, tighten the knob to 8 in.-lbf for a secure connection.

Installation for the optional front panel binding posts is the same as for the rear terminal binding posts.

Do not use lubricants or contact cleaners on the binding posts. Certain chemical agents can damage the LEXAN material of the binding post, causing the part to fail.

Figure 3-8. Input Binding Post

Control Connector

A ten-pin terminal block (TB301) connector and a quick-disconnect mating plug (RTB1) are provided for connecting remote sense leads, external V/I monitors, an external programming input, and external control lines (see Figure 3-9). You must remove the safety cover before you can disconnect mating plug RTB1.

Consistent with good engineering practice, all leads connected to the control connector should be twisted and shielded to maintain the instrument’s specified performance.

Figure 3-9. Control Connector

Installation 41

Image 41

Agilent Technologies 5951-2827, 5951-2826 manual Input Binding Post Control Connector

Contents

Operating Manual Agilent Part No Microfiche Part No Updated April Certification Safety Summary Symbol Description Safety SummaryHerstellerbescheinigung Manufacturer’s Declaration Printing History Table of Contents Calibration Local OperationRemote Operation Considerations for Operating in Constant Resistance Mode Reader Path What’s In This ManualOptions General Information Specifications Safety Requirements Modes Continuous Mode Regulation Constant Resistance Mode RangesPulsed Mode 6060B 6063B Current Readback Temperature Coefficient Supplemental Characteristics 6060B 6063BResolution Bandwidth Maximum Readback Capability Maximum VA Peak Inrush Current 2.5 a typical Supplemental CharacteristicsCurrent Slew Rate Rate # High Range Step Low Range Step Transition Time Model 6063B Range Transient Current Level Resistance Slew RateOvershoot With unit on 6060B 6063B 10%With unit off WidthPage Front Panel Description IntroductionRemote Programming Operation Overview Programmable Features Local/Remote ControlConstant Current CC Mode Modes of Operation Software Current Limit Triggered Current Level Immediate Resistance Level Constant Resistance CR ModeSlew Rate Transient Resistance Level Constant Voltage CV ModeTriggered Resistance Level Triggered Voltage Level Immediate Voltage LevelTransient Voltage Level Transient Operation Pulsed Transient Operation Hpsl Command Description Selects pulsed transient operation Selects the external trigger inputSets pulse width to 1 millisecond Selects the external trigger input source Triggering a transient pulse Triggering a preset levelToggling Slew Rate And Minimum Transition Time Risetime Transition Limitation Input Current, Voltage, and Power Measurement Transition Times and Slew Rates Short On/Off Reading Remote Programming Errors Saving and Recalling SettingsInput On/Off Status Reporting Resetting Latched Protection Protection FeaturesOvervoltage Overcurrent Overpower Control ConnectorOvertemperature Reverse Voltage External Programming Input FaultMonitor Outputs Port On/Off Inspection Check Line Voltage Location and CoolingTurn-On Checkout Line Voltage Fuse Agilent Part No Voltage Select Switches Gpib Errors Input Errors Display Description Connect The Power CordError Turn-On/Selftest Controller Connection Power TestGpib Connector Wire Size Strip back Rear Panel Connectors and SwitchesGpib Address AWG Input Binding Post Control Connector +S and -S Pins 3IM and VM Common Sense Switch Trigger Connector Application Connections Zero-Volt Loading Connections Maximum Wire Lengths to Limit Voltage DropsParallel Connections 11. Local Sensing 13. Parallel Operation Page Local Operation Front Panel Controls and Indicators Description Controls and Indicators Description Function Keys Local Control Overview Turning the Input On/Off Using The Function Keys∙ Short on Recommended Programming Sequence Setting CC Values Setting the Mode of OperationCC Programming Ranges Function Key Display Examples Setting CR Values Examples Setting CV Values Function Key Display Range of Values Continuous Pulse Train Programming Ranges Shorting The Input Using The System Keys Displaying Error Codes Setting The Electronic Load’s Gpib Address Changing Wake-up Settings Factory Default Settings Function 6060B 6063B Recalling the Factory Default Values Gpib Address Enter/Output StatementsOutput Enter Remote Programming Commands Sending a Remote CommandGetting Data Back Output 705 MEASCURR? Ranges ModesTransient levels Slew Rates Remote Programming Flowchart Sheet Remote Programming Flowchart Sheet CR Mode Example CC Mode ExampleCV Mode Example Pulsed Transient Operation Example Continuous Transient Operation Example Output 705TRAN on Output 705INPUT on Hpsl Command Short FormRemote Programming Ranges Function Constant Current CC 6060B Constant Resistance CRConstant Voltage CV Transient OperationPage Example Programs Equipment Characteristics Recommended ModelEquipment Required Equipment Required for Calibration Calibration Commands Example Program Calibration Flowcharts Calibration Information 6060B 6063B Supply Shunt Values Settings Calibration Flowchart Calibration Flowchart Calibration Flowchart Pause Program ListingWait END if Print Voltage Calibration Pause Subend Else Line ExplanationPage Considerations For Operating In Constant Resistance Mode Considerations For Operating In Constant Resistance Mode Considerations For Operating In Constant Resistance Mode Index Index Index 24, 25, 26 Index Agilent Sales and Support Office Agilent Sales and Support Offices Manual Updates