Line Indicates Remarks | Atlas Air Compressor specs

Instruction book

	Line	Indicates	Remarks

	1	Sensor which is active	The unit for pressure can be bar, psi or kg/cm2 depending on the
		Sensor which is active	programmed selection. The unit for temperature can be °C or °F.
		and the actual reading
		and the actual reading	See section 8.12.
			See section 8.12.
	2	-	-
			Examples:
	3	Compressor status	-	Compressor Off
			-	Compressor Running
			If the unit is shut down, the regulator will automatically show a shut-
	3	Shut-down	down message on the display (see section 8.3). It remains possible
	3	Shut-down	to have a closer look at other parameters related to the shut-down

			by means of the menus.
	3	Service required	Indicates that the unit needs servicing. Consult section 8.13 to find
	3	Service required	out the exact cause for this message.
			out the exact cause for this message.
			Indicates that a sensor is out of order:
			-	Outlet pressure transducer
	3	Sensor error	-	On Full-Feature compressors, the dewpoint sensor
	3	Sensor error	Stop the compressor. Switch off the voltage and depressurize the

			compressor. Check the sensor wiring. Replace the sensor or
			transducer, if necessary.
	3	Remote control	Indicates that the compressor is set in remote control. Consult Atlas
	3	Remote control	Copco.
			Copco.
	4	Functions of keys	See section 1.5.7.
	4	below display
		below display
		Symbols:	Indicating the status of each compressor module

	4	-	indicating that the compressor module is available (ready to run)
	4	▄	indicating that the compressor module is running
		- (blinking)	indicating that the compressor module is not available (due to
		- (blinking)	minimum stop time or too many starts)
			minimum stop time or too many starts)
		* (blinking)	indicating that the compressor module is shut down

Note

When more than one message needs to be displayed (e.g. both warning and service), the messages will be displayed one after the other for 3 seconds.

Press key (F3) on the main screen to check which compressor module is running or stopped.

Element 1	Stopped
Element 2	Running
Element 3	Stopped	↓
Menu
F1	F2	F3

Fig. 8.3 Element status screen, typical example

2920 1521 00

43

Image 43

Atlas Air Compressor manual Line Indicates Remarks, Element status screen, typical example

Contents

No 1521 Registration code APC SF / 38 Instruction book Instruction book Skid Tank-mounted Twin Service warning message exists General description Leading Particulars SF4 Skid Control panel Air outlet valve SF4 Tank-mounted SF8FF Multi Details of a compressor module on SF Tank-mounted Cooling and condensate drain systems Fig Air flow Protecting the compressor Regulating system on SF Skid Tank-mounted Twin Automatic restart after voltage failure Monitoring components subject to serviceRegulating system on SF Multi Controlling the compressor Designation Function Control panel Fig Tabulator key 4-Fig Display keysOperating condition of a compressor module Scroll keys 3-Fig 13 Menu flow, SF Multi Selecting a menu 14 Electric cabinets, SF Multi Electric cabinet on SF Multi Compressed air circuit Air dryer on SF Full-Feature FigRefrigerant circuit Dimension drawings Figs .1 up to Installation 9820 4054 00/1 Dimension drawing, SF 6-8 Multi Dimension drawing, SF 11-15 Multi Instruction book Installation proposal Fig Instruction book General Electrical connectionsConnections Skid Tank-mounted Twin SF Multi TSHH20 Pictographs Pictographs Initial start-up Operating InstructionsStarting During operation Taking out of operation at end of compressor service lifeStopping Service plans on SF Multi MaintenancePreventive maintenance schedule for the compressor Before carrying out any maintenance or repair Yearly Monthly Coolers Adjustments and Servicing ProceduresAir filter 1-Figs .7/1.8 Belt exchange/tensioning Fig Testing Safety valveOperating Problem Solving Electric cable size for SF1-8 Principal DataElectric cable size for SF 6-15 Multi Overload relays for SF6-15 Multi Overload relays for SF1-8 Reference conditions Main fuses for SF1-8Main fuses for SF6-15 Multi Reference conditions/limitations 11 SF2-4 145 psi 60 Hz SF1-4 8bar 50 HzSF2-4 10 bar 50 Hz 10 SF1-4 100 psi 60 Hz 13 SF6-15 Multi 10 bar 50 Hz 12 SF6-15 Multi 8 bar 50 Hz14 SF6-15 Multi 100 psi 60 Hz SF11 SF15 145 psi 15 SF6-15 Multi 125 psi 60 Hz16 SF6-15 Multi 145 psi 60 Hz SF11 SF15 125 psi Menu-driven control programs Regulator Functions for SF Multi Main screen Function of control programs Program/Function Description Element status screen, typical example Line Indicates Remarks Quick look at actual compressor status ProcedureCalling up other menus No message exists Status data menuShut-down message exists Shut-down reset Measured data menu Service warning message exists Test menu Counters menu Modifying parameters Modify parameters menu Modifying the pressure bands Checking protections for compressor modules Modifying protection settings Service plans Modifying service plans Resulting service actions to be carried out Programmed service plan intervals Service plans IntervalsService actions according to Programming Clock function Programming start/stop/pressure band commands Instruction book To modify a command To activate/deactivate the timer Instruction book To delete commands Adding a command between two existing commands Deleting a specific start/stop/pressure band command Configuration menuDeleting all commands Deleting all commands related to a specific day Service menu Service plans ABI Saved data menu Regulation settings Minimum Nominal Maximum Setting Programmable settings Conversion List of SI Units Into US/BRITISH Units Service settings Minimum Nominal Maximum Setting Part number Description PED Class Components subject to 97/23/EC Pressure Equipment DirectiveOverall Rating Instruction book Instruction book Wnership Data Safety Preca Utions