Barco G500 12. DISPLAY SETUP

12. Display setup

12. DISPLAY SETUP

Overview

• Full screen representation

• Startup screen

• Textbox

• Takescreenshot

• Menu bar position

• Status bar position

• Sliderbox position

• AutoImage Setup

•Blanking

12.1 Full screen representation

Purpose of the Full screen representation

TheFull screen representation function forces to use the complete native resolution of the LCD panels independently of the native

resolution of the source.

Note that the full screen representation does not preserve the aspect ratio of the source, i.e. when the asp ect ratio of the active

imageis not the same as the projector (in this case 1920/1080 or 1.77:1), the image will end to be distorted (stretched or shrinked).

How to enable/disable the full screen representation?

1. Press MENU to activate the Tool bar

2. Press →to select the Display setup item

3. Press ↓to Pull down the Display setup menu

4. Use ↑or ↓to select Full screen representation

5. Press →to pull down the menu

6. Use ↓or ↑to select ON or OFF

7. Press ENTER

Thefull screen representation will not guarantee the best image qu ality,therefore the Show native resolution

has to be selected.

Theshow native resolution f unction on the other hand forces to use the native resolution of the source.

TheFull screen representati on functionoverrules the show native resolution function.

Theaspe ctratio setting is greyed out w hen enabling the full screen representation.

12.2 Startup screen

What can be done ?

Whenthe startup screen is enabled, the identification screen is displayed for a few seconds at startup. Thisstartup screen can also

be disabled.

R5976491 IQ PRO G500 01/02/2007 105

Contents

Main Product revision Federal Communications Commission (FCC Statement) End User License agreement (EULA) Copyright Page Page TABLE OF CONTENTS Page Page Page 1. Packaging and Dimensions 1. PACKAGING AND DIMENSIONS 1.1 Box content Content 1.2 Projector Packaging Way of Packaging 1.3 Lens Packaging Way of Packaging CAUTION:Never transport the projector with the lens mounted on it ! 1.4 Dimensions Dimensions overview Hot air out 1. Packaging and Dimension s 2. INSTALLATION GUIDELINES 2.1 Safety warnings Mercury Vapor Warnings 2.2 Installation guidelines Ambient temperature check 2.3 Projector configurations The different configurations Page Positioning the projector CAUTION:Only foriQ Pro: CAUTION:Never place the projector on either side ! 2.4 Lenses 2.4.1 Lenses Available lenses 2.4.2 Lens formulas Formulas 2.4.3 Lens installation How to install ? Page 2.5 Batteries Page 3. CONNECTIONS 3.1 Power connection 3.2 Input source connection 3.2.2 Input facilities 3.2.3 5-Cable input Input specifications Which signals can be connected ? How to select a source on the 5 cable input ? 3.2.4 Composite Video Input Composite video connection Input specifications How to select a Composite Video Input ? Page Page Page How to set up the 5 cable extended configuration ? 3.2.9.3 S-Video extended configuration How to set up the S-Video extendedconfiguration ? 3.2.9.4 Summarizing Summarizing the extended connections Page 4. GETTING STARTED 4.1 RCU & Local keypad How controlling the projector ? Location of the local keypad ? Remote control functions. Diagnose LEDs 4.2 Terminology overview 4.3 Switching on How to switch on. Starting image projection. 4.4 Lamp runtime Lamp runtime indication while running WARNING:Usinga lamp f or more than x hours is dangerous as the lamp could explode. 4.5 Lamp error What happens in case of a lamp error ? 4.6 Quick set up adjustments How to connect ? Specifications of the RC input AB C D 4.7 Projector address 4.7.1 Address setting Why a projector address ? Set up an individual Projector Address. Projector controlling. 4.8 Controlling the projector Input Selection Picture Controls The Pause Key 4.9 Digital Zoom How to Zoom ? 4.10 Menu structure PC like menustructure 4.11 Using the menu 4.12 Using the Dialogboxes Entering numeric values using the arrow keys on the remote control Entering numeric values using the arrow keyson the local keypad Page 5. SOURCE SELECTION 5.1 Source selection Selecting a source How to select a source ? When to select Data on BNCs 5.2 Composite Video How to select one of the 7 composite video inputs ? Adjustments on a Composite video signal 5.3 S-Video When How to select one of the 3 S-Videoinputs ? 5.4 The Video Selector Video selector modes How to display the Video Selector? How to select an input on the Video Selector? How to disable the extended Video Selector Page 6. GENERAL MENU 6.1 Pause Interrupting the image projection How to interrupt the image projection ? 6.2 Freeze 6.3 Standby Timer Purpose of the Standby Timer How to enable the timer ? 6.4 Audio (Optional) Page 6.5 Identification The projectors identification screen How to display the identificationscreen ? Page 7. IMAGE MENU 7.1 Settings Page How to change the Color ? 7.1.4 Tint (hue) How to change the Tint ? 7.1.5 Sharpness How to change the sharpness ? 7.1.6 Gamma How to change the Gamma 7.1.7 Phase Phase adjustment 7.2 Aspect ratio Aspect ratios 4:3 16:9 2.35:1 16:9 2.35:1 Projector setting Source How to change the Aspect ratio ? How to set a custom Aspect ratio ? 7.3 Show native resolution How to enable the Show native resolution function? 7.4 Keystone How to perform a Keystone correction ? 7.5 Color temperature How to select a preset color temperature ? How to start up the custom color temperature ? 7.6 Filmmode detection Enabling/disabling the filmmode detection 7.7 Blanking Blanking in the Image menu Black level 7.8 Input balance Introduction: Unbalanced color signals Analog Digital Conversion The objective of input balancing How can it be done ? A B Black balance Performing White input balance Remark on the input balance of a componentvideo source 7.9 AGC on Video Enabling/disabling the AGC 7.10 Manual Gain Control How to set the Manual Gain Control ? Page 8. TOOLS MENU 8.1 Introduction to PiP What are the different possibilitieswithin the PiP mode ? What are the different PiP layouts ? PiP dedicated buttons 8.2 PiP select PiP layouts How to change the PiP configuration ? 8.3 PiP add window How to add a window ? 8.4 PiP remove window How to remove a window ? 8.5 PiP layout 8.5.1 PiP Save How to save a layout ? Page 8.6 PiP Adjust PiP adjust How to adjust a window in the layout ? 8.7 Diagnostics How to display the diagnostics menu ? Page Page 9. Signal Menu 9. SIGNAL MENU 9.1 Switching mode Switching from one source to another How to select a switching mode ? 9. Signal Menu 9.2 Background Purpose How to change the background ? 10. LAMP MENU 10.1 Runtimes How to display the lamp runtimes ? 10.2 Mode What are the different lamp modes ? How to select the lamp mode ? 10.3 Power mode (only active in the iQG/R 500) How to select a Power mode ? 10.4 History How to view the history ? 10.5 Reset runtime When to reset the lamp runtime ? How to reset the lamp runtime in theiQ/iD ? How to reset the lamp runtime in the SIM5Plus? 10.6 Runtime warning How to set the lamp runtime warning? Page 11. IM AGE F ILES M ENU 11.1 Load file Howtoloadafile? What to do if the image is not perfect ? 11.2 Auto Image How to launch Auto Image? 11.3 Edit file What can be done with the Edit file menu ? How to edit a file ? Which items can be adjusted ? Advanced video settings Advanced Data settings 11.4 Ren ame file How to rename a file ? 11.5 Copy How to copy a file ? 11.6 Delete How to delete a file ? 11.7 Forced file load How to set a file to be loaded ? Page 12. DISPLAY SETUP 12.1 Full screen representation Purpose of the Full screen representation How to enable/disable the full screen representation? 12.2 Startup screen 12.3 Textbox How to enable/disable the Textbox? 12.4 Take screenshot How to take a screenshot ? 12.5 Menu bar position How to center the menu ? 12.6 Status bar position How to center the menu ? 12.7 Sliderbox position How to reposition the sliderbox? 12.8 AutoImage Setup How to set up AutoImage? How to perform AutoImage ? 12.9 Blanking How to blank the image ? Page 13. INSTALLATION MENU 13.1 Lens adjustments How to Zoom/focus or shift ? 13.2 Projector address How to change the projectors RC5 address ? 13.3 Orientation 13.4 Language List of languages How to change the Language ? 13.5 Quick access keys How to get an overview of the quick access keys ? How to program the quick access keys ? 13.6 RS232 baudrate How to change the baudrate? 13.7 Automatic startup How to enable/disable the Automatic startup? 13.8 Security How to activate the security mode ? How to disable the security mode ? 13.9 Change password How to change the password ? 13.10 Gemini installed (only for GEMINI CADWALL systems ! ) When to enable ? How to enable Gemini ? 14. IQ NETWORK 14.1 Network architecture Topology WAN LAN 14.2 Networkfunctionality 14.3 iQ Pro Server specifications Specifications of the iQ Pro Server platform 14.4 Getting started CAUTION:Important ! 14.4.1 Connections Front plate (Layer 3) layout D ABC How to connect the Single Board Computer? Page Projector Standby state setting Projector On state setting Automatic start up: How to set the automatic startup ? 14.4.4 Configuring the client software How to start up the client software ? How to add a projector to the projector list How to add a projector group to the projector grouplist ? How to add projectors to a group ? How to connect to a projector or group of projectors ? The Target information block Page Page Start Meetings control How to configure the Server settings ? Page Page 14.5 Control 14.5.1 Description LAN ... What can be controlled ? Page 14.5.4 The source selection screen How to select a source ? 14.5.5 The PiP screen How to perform operations on a PiP layout Importing/exporting a layout Page Color temperature preset settings Custom color temperature setting Page Page Page 14.6 Management & diagnostics 14.7 Configuration Page Page 14.8 DropZone How to add a projector to the list ? How to select an existing projector byits name ? How to select an existing projectorby its location ? 14.8.3 File dropping/launching File dropping File launching How to set the drop mode ? How to drop a file using the drag method ? How to drop a file using the Open dialog box ? What to do with the launched files once disconnected ? Page How to perform remote desktop sharing ? How to take (mouse and keyboard)Control over the desktop? How to release control over the desktop? How to forward control over the desktop ? 14.8.6 DropZone settings How to setup the DropZone ? 14.9 The Webclient Web based functionality How to access the web client via the internetbrowser ? Page 15. General guidelines on Network Configuration 15. GENERAL GUIDELINES ON NETWORK CONFIGURATION 15.1 General Network Microsoft NT Domain TCP/IP 15.2 The Internet and Web services 15. General guidelines on Network Configuration Microsoft Exchange and Outlook A. EXCHANGE A.1 Exchange Installation A.1.1 Installation procedure Creating a user account and mailbox Installing and configuring MicrosoftOutlook (on the projector) Enabling the account Installing and configuring the iQProEXCHservice A.1.2 Troubleshooting What can go wrong and what to do ? A.2 Exchange Integration A.2.1 Command How are the commands build up ? Page Page Organizational Forms Default form Page Page B. SNMP services B. SNMP SERVICES B.1 SNMP installation How to install SNMP (only if necessary) How to configure SNMP (only if necessary) B.2 SNMP integration B. SNMP services C. Troubleshooting C. TROUBLESHOOTING FAQ tabl e C.1 FAQ table What to do when... ? Page D. Cleaning the dustfilters D. CLEANING THE DUSTFILTERS D.1 Dustfilters Location of the filters D.2 Cleaning How to clean the dustfilters ? D. Cleaning the dustfilters E. STANDARD IMAGE FILES E.1 Table overview Table overview Page Page Page Page Page Glossary GLOSSARY Page INDEX A B C D L M N O P Q R S T Page Revision Sheet