Barcographics 8200 | Barco R9001330 instruction

Service Mode

-Baud rate : transfer speed for communication with a IBM PC (or compatible) or MAC. The baud rate of the projector must be the same as the baud rate of the connected computer. When there is a difference, consult Set up of the baud rate for commu-

nication with a computer in chapter Connections.

-Projector Run Time : gives the total run time since the first start up. All projectors leave the factory with a run time of approximately 24 hours.

-Projector Serial number : indicates the fabrication number of the projector. This number can be useful when calling for technical assistance.

13-6		5975288 BARCOGRAPHICS 8200 110497
13-6		5975288 BARCOGRAPHICS 8200 110497

Image 101

Barco R9001330 owner manual Barcographics 8200

Contents

Barco Projection Systems Graphics R9001330Page Table of Contents Start UP of the Adjustment Mode 11-15 Rcvds On safety Safety instructionsOn installation On cleaning Prescription de sécurtié Instructions pour l’installation OWNER’S Record Installation instructions Fédéral communication commission FCC statement Federal communication commission FCC statement Cordon d’alimentation avec connecteur Ansi Prescriptions de securite généralesCordon d’alimentation avec connecteur CEE7 Power cord with Ansi 73.11 plug General safety instructionsMains lead AC Power cord with CEE 7 plug ’Installation On Installation Page On Servicing On Cleaning Eclairage On illumination Safety Instructions On Repacking Unpacking Dimensions Battery Installation on the RCU Unpacking & Dimensions Unpacking Pull To open Projector dimensions Battery installation in the RCU Installation Guidelines Installation Guidelines What about ambient light ? Installation guidelinesEnvironment What image size? How big should the image be? Installation Guidelines Which screen type? Inputs and computer video format input compatibility Installation Guidelines Where to install the projector?Definitions of the Abbreviation on drawings Lens type selection Table mounting of the Barcographics Ceiling mounting of the Barcographics How to install the projector? Installation Guidelines How to install a projection lens? Projector configuration Installation Set UpInstallation SET UP Rear/Ceilin g Rear/T ab l e Ro n t/Ceilin g Ro n t/T able Enter Location and Function of Controls Front panel terminology Local keypad Remote controlLocation and Functions of Control Front panel terminology Diagnostics code a source number Local keypad Remote controlControl Panel Terminology Remote Control RCU Local keypad Control disk on RCU or + and keyscursor keys to Terminology Power Connection Power Connection Fuses Power mains cord connectionSwitching on Stand by button 980 h Switching to stand-by Switching off Peripheral equipment connection ConnectionsInput Module Connections Input module insertion into the projector Input connections DI a G no S TI CS Video/S-video input module Input Slots Straps on module level DI AG NOS TI CS RGB analog input module RGB input selection RGB-SOG= sync on green Sync Blue luma Luma Red luma Component input module Indication on the input slot menu Component input selection Input selection RGB3S/RG3sB input module Floating or non-floating input Red Strap yes non floating See Change Baudrate PC in chapter Service mode Set up of the baud rate for communication with a computer Connecting a VS05 to the projector Controlling Controlling Point the front of the RCU to the reflective screen surface How to use the RCU? How to control the projector or projectors Software set up of the projector addressUsing the RCU Projector address How to program an address into the RCU? How to display a projector address?Picture controls with direct access Brightness Control Contrast Control Phase ControlColor Saturation Sharpness Control Start UP of the Adjustment Mode Start Up of the Adjustment Mode Adjustment Mode Password Guided Adjustment Mode Guided Adjustment Mode Guided Adjustment Mode is not active File Service Picture Tuning Geometry Random Access Adjustment ModeRandom Access Adjustment Mode Starting up the Random Access Adjustment Mode File service Load file Edit Edit file Read Amds Options Press Exit to leave the Edit File Option menu Rename File Rename Copy File Copy Delete File Delete File Options Picture Tuning Still Video Sync slow/fast Color Balance Color Balance Gamma Shift Geometry Size Side keystone Blanking Blanking Options Options Convergence Configuration Internal Patterns InstallationInstallation Starting up the Installation Mode Input Slots Convergence Convergence and press Enter to Green focusing Red on green convergence Barcographics 8200 12-7 Blue on green convergence Internal Patterns Configuration Service Mode Service Mode Service Starting up the Service Mode Barcographics 8200 13-3 13-4 Barcographics 8200 Software version Identification 13-6 Barcographics 8200 How to enable or disable the password function ? Change Password 13-8 Barcographics 8200 Change Language Service Mode How to change the password ? Change Baudrate PC Change Projector Address Service Reset Lamp Runtime Lamp Run Time History Panel Adjustments Panel Adjustments Preset Input Balance Preset Input Balance 60Hz Tracking Hz Tracking I2C Diagnosis I2C diagnosis Optional Equipment IR remote receiver Hardwired RCUOptional Equipment RCVDS05 IR Receiver VS05 Rcvds 800 / Rcvds D9-D9 communication cable Din Mini8-D9 adapter cable Projector Transport Handle Projector Frame for Dual or Triple Configurations Multifunctional flight case Features 14-8 Barcographics 8200 Standard source set up files Appendix a Standard Source Set Up Files MAC4 XGA75GS MAC6 Battery replacement in the RCU Appendix B Battery Replacement in the RCU Focusing the lens Appendix C Focusing the Lens Lens Cleaning Procedure Appendix D Lens Cleaning Procedure Appendix D Lens Cleaning Procedure Source numbers 90 Appendix E Source Number 90 Lenses Appendix F Lenses Lens formulas to calculate the projector distance Insert card RCU