Manuals / Barco / Computer Equipment / Barcode Reader

Barco R9001330 Appendix C Focusing the Lens, Focusing the lens, Lens holder Fastener Lens

Models: R9001330

1 131

Download 131 pages 39.45 Kb

Page 125

Image 125

Appendix C : Focusing the Lens

Focusing the lens

Loosen the fastener ring of the lens by turning counter clockwise.

Focus the image by turning the lens barrel to the left or the right. Attention : Do not turn out the lens too far, otherwise it will fall out of the lens holder.

When the image is focused, secure the correct position of the lens with the fastener ring by turning this ring clockwise.

Lens holder

Fastener

Lens

5975288 BARCOGRAPHICS 8200 110497		C-1
5975288 BARCOGRAPHICS 8200 110497		C-1

Page 125

Image 125

Barco R9001330 owner manual Appendix C Focusing the Lens, Focusing the lens, Lens holder Fastener Lens

Contents

OWNERS MANUAL BARCO PROJECTION SYSTEMS GRAPHICSR9001330 Printed in Belgium Produced by BARCO NV, April All rights reservedTrademarks are the rights of their respective owners Table of Contents Set up of the baud rate for communication with a computer Table of ContentsHow to display a projector address? How to program an address into the RCU?Table of Contents Hardwired RCU Table of ContentsSafety instructions Safety InstructionsOn safety On installationPrescription de sécurtié Instructions pour l’installationRemarque sur la Sécurité DONNEES POUR LE PROPRIETAIREInstallation instructions Notice on safetyOWNER’S RECORD PART NUMBER SER. NUMBER DEALERLe point d’exclamation dans un triangle indique Fédéral communication commission FCC statementPrescription de sécurtié Safety Instructions Federal communication commission FCC statementSECURITE Prescriptions de securite généralesA. Cordon d’alimentation avec connecteur CEE7 B. Cordon d’alimentation avec connecteur ANSION SAFETY General safety instructionsA. Mains lead AC Power cord with CEE 7 plug B. Power cord with ANSI 73.11 plugLes fentes et les ouvertures pourvues dans le boîtier et au dos ou L’InstallationPrescription de sécurtié Slots and openings in the cabinet and the sides are provided for On InstallationSafety Instructions Page On Servicing On CleaningSafety Instructions Call for service in the following conditionsEclairage On illumination On RepackingSafety Instructions To ensure the highest optical performance and resolution, the projection lenses are specially treated with an anti-reflective coating, therefore avoid touching the lens. To remove dust on the lens, use a soft dry cloth. Do not use a damp cloth, detergent solution, or thinner. Follow the lens cleaning procedure on Appendix D in the Owners ManualUNPACKING DIMENSIONS BATTERY INSTALLATION ON THE RCU Unpacking & DimensionsPull To open UnpackingUnpacking & Dimensions Unpacking & Dimensions Projector dimensionsUnpacking & Dimensions Battery installation in the RCUINSTALLATION GUIDELINES Installation GuidelinesHow to install the projector? Environment What about ambient light? Which screen type?Environment Installation guidelinesWhat about ambient light ? Installation GuidelinesWhat image size? How big should the image be? Which screen type?Installation Guidelines Screen widthInputs and computer video format input compatibility Where to install the projector?Definitions of the Abbreviation on drawings Lens type selectionTable mounting of the BARCOGRAPHICS Ceiling mounting of the BARCOGRAPHICSInstallation Guidelines CD = B - AHow to install the projector? How to install a projection lens?BARCO projection table Installation GuidelinesProjector configuration Installation Set UpINSTALLATION SET UP F ro n t/Ceilin g F ro n t/T able Installation Set UpRear/Ceilin g Rear/T ab l e Installation Set Up ENTERADJUSTMENT MODE INSTALLATIONLOCATION AND FUNCTION OF CONTROLS Front panel terminology Local keypad Remote controlLocation and Functions of Control Location and Functions of Control Diagnostics code a source numberFront panel terminology Control Panel Terminology b. Remote controla. Local keypad Location and Functions of ControlLocation and Functions of Control Remote Control RCULocal keypad E N T E RControl disk on RCU or + and - keyscursor keys to TerminologyLocation and Functions of Control key downPOWER CONNECTION Power ConnectionSwitching on Power mains cord connectionFuses Power ConnectionTo start image projection Power ConnectionPower Connection Switching to stand-bySwitching off Connecting an IR Remote Receiver Connecting a computer Connecting a RCVDS05 Connecting a VS05Connections INPUT MODULE CONNECTIONSConnections Input connectionsInput module insertion into the projector Connections Video/S-video input moduleConnections EXIT returns to operational modeFactory preset strap on, input non floating Straps on module levelConnections Floating or non-floating input Video inputConnections RGB analog input moduleConnections RGB input selectionKey in the corresponding slot number on the RCU or the local keypad Straps on module levelENTER Push the control disk up or down to select Installation and pressConnections Connections Component input moduleIndication on the input slot menu Component input selectionConnections Straps on module levelInput selection RGB3S/RG3sB input moduleConnections Indication on the input slot menuStraps on module level ConnectionsConnections Set up of the baud rate for communication with a computerSee Change Baudrate PC in chapter Service mode Connecting an IR Remote Receiver 800 to the projector Connecting a RCVDS 05 to the projectorConnecting a VS05 to the projector ConnectionsHow to display a projector address How to use the RCU Projector addressHow to program an address into the RCU Picture controls with direct accessControlling How to use the RCU?b. How to control the projector or projectors a. Software set up of the projector addressc. Using the RCU Projector addressHow to program an address into the RCU? How to display a projector address?Picture controls with direct access Brightness ControlContrast Control Phase ControlColor Saturation Sharpness ControlSTART UP OF THE ADJUSTMENT MODE Start Up of the Adjustment ModeStart Up of the Adjustment Mode Adjustment ModeSelect a path from below GUIDED RANDOM ACCESS INSTALLATION SERVICE Source Select with or then ENTER EXIT to returnYour password contains 4 digits Start Up of the Adjustment ModeGUIDED ADJUSTMENT MODE Guided Adjustment ModeThe Guided Adjustment Mode is not active Guided Adjustment ModeADJUSTMENT MODE GUIDEDFile Service Picture Tuning Geometry Random Access Adjustment ModeRANDOM ACCESS ADJUSTMENT MODE Random Access Adjustment Mode Starting up the Random Access Adjustment ModeRANDOM ACCESS ADJUSTMENT MODE ADJUSTMENT MODERandom Access Adjustment Mode File serviceRandom Access Adjustment Mode Load fileENTER Edit fileRandom Access Adjustment Mode Random Access Adjustment Mode Read AMDSEDIT FILE OPTIONS OptionsRandom Access Adjustment Mode Vertical sync polarity leading or trailing Random Access Adjustment ModeRandom Access Adjustment Mode RenameCOPY FILE CopyRandom Access Adjustment Mode Random Access Adjustment Mode DeleteRandom Access Adjustment Mode Picture TuningFile Options Random Access Adjustment Mode Sync slow/fastStill Video Random Access Adjustment Mode Color BalanceRandom Access Adjustment Mode GammaPICTURE TUNING GAMMAShift GeometryRandom Access Adjustment Mode ENTERRandom Access Adjustment Mode SizeSIDE KEYSTONE Side keystoneRandom Access Adjustment Mode Random Access Adjustment Mode BlankingTOP BOTTOM LEFT RIGHT Select with or then ENTER EXIT to return Random Access Adjustment ModeBLANKING Random Access Adjustment Mode OptionsConvergence Configuration Internal Patterns InstallationINSTALLATION Installation Starting up the Installation ModeInstallation Input SlotsENTER Component Video - SOY component videoInstallation ConvergenceInstallation Green focusingConvergence and press ENTER to Installation Red on green convergenceIf both lines are correctly converged, continue with screw InstallationInstallation Blue on green convergenceInstallation ConfigurationInternal Patterns SERVICE MODE Service ModeIdentification Change Password Change Language Change Projector Address Change Baudrate PC Reset Lamp Run TimeENTER Starting up the Service ModeService Mode SERVICE Service ModeSERVICE CHANGE PASSWORDSERVICE Service ModePANEL ADJUSTMENT RED COARSE PRESET INPUT BALANCEService Mode Identificationsoftware version nication with a computer in chapter Connections Service ModeService Mode Change PasswordHow to enable or disable the password function ? Password enabled Service ModePassword disabled strap on legService Mode How to change the password ?Change Language Service Mode Change Projector AddressChange Baudrate PC Service Mode Reset Lamp RuntimeService Mode Lamp Run Time HistorySERVICE ENTERService Mode Panel AdjustmentsService Mode Preset Input BalanceService Mode 60 Hz TrackingService Mode I2C diagnosisSERVICE I2C DIAGNOSISMechanical shutter Adjustable lensholder OPTIONAL EQUIPMENT IR remote receiver Hardwired RCU RCVDS05 VS05Optional Equipment MAGIK interface Adapter and communication cablesIR Receiver Hardwired RCUOptional Equipment shield conductorOptional Equipment RCVDS 800 / RCVDSVS05 Adapter and communication cables MAGIK Interfacea. D9-D9 communication cable Optional Equipmentb. Din Mini8-D9 adapter cable Ceiling Mount Kit CM100c. D25-D9 adapter cable d. 5 BNC to 5 BNC cableOptional Equipment Projector Frame for Dual or Triple ConfigurationsProjector Transport Handle Optional Equipment FeaturesMultifunctional flight case Optional Equipment Adjustable lensholderMechanical Shutter Standard source set up files Appendix A Standard Source Set Up FilesAppendix A Standard Source Set Up Files Appendix A Standard Source Set Up Files Appendix A Standard Source Set Up Files Battery replacement in the RCU Appendix B Battery Replacement in the RCULens holder Fastener Lens Appendix C Focusing the LensFocusing the lens Lens Cleaning Procedure Appendix D Lens Cleaning ProcedureCleaning procedure for HD1.5-31 lens and HD3-5.31 lens Cleaning procedure for the other HD lensthe lens. Wipe at a speed that is equal to the evaporation rate. This is very important to prevent streaking and spotting. Start your wiping at one side of the lens and, with successive wipes, move to the other side. Turn the pad over for each wipe, then inside out. Do not make more than one wipe per clean area of pad. Be careful of the painted edge, since acetone will soften it Appendix D Lens Cleaning ProcedureSource numbers 90 Appendix E Source Number 90Lenses Appendix F LensesHD1.21 HD2.21Appendix F Lenses Lens formulas to calculate the projector distanceR C U Insert card RCUR C U INPUT SOURCES