Starting up the Service Mode | Barco R9001330 specification

Service Mode

Starting up the Service Mode

Push the control disk up or down to highlight Service and then press

ENTER.

Some items in the Service mode are password protected (when the password function is active). Enter your password to continue. All other password protected items are now available if you stay in the adjustment mode.

The service menu is built-up in two parts which are connected together with the 'more' item.

If the disered item is not in the list of the displayed menu, select more with the control disk and push ENTER to display the other items in the service menu.

ENTER continues to the Service mode selection menu. EXIT returns to operational mode.

ADJUSTMENT MODE

Select a path from below :

GUIDED

RANDOM ACCESS

INSTALLATION

SERVICE

SERVICE

IDENTIFICATION

CHANGE PASSWORD

CHANGE LANGUAGE

CHANGE PROJ. ADDRESS

CHANGE BAUDRATE PC

RESET LAMP RUNTIME

LAMP RUNTINE HISTORY

MORE...

Select with	or
then <ENTER>

<EXIT> to return.

SERVICE

PANEL ADJUSTMENTS

PRESET INPUT BALANCE

60Hz TRACKING

I2C DIAGNOSIS

MORE...

Select with or then <ENTER> <EXIT> to return.

13-2		5975288 BARCOGRAPHICS 8200 110497
13-2		5975288 BARCOGRAPHICS 8200 110497

Image 97

Barco R9001330 owner manual Starting up the Service Mode

Contents

Barco Projection Systems Graphics R9001330Page Table of Contents Start UP of the Adjustment Mode 11-15 Rcvds On safety Safety instructionsOn installation On cleaning Prescription de sécurtié Instructions pour l’installation OWNER’S Record Installation instructions Fédéral communication commission FCC statement Federal communication commission FCC statement Cordon d’alimentation avec connecteur CEE7 Prescriptions de securite généralesCordon d’alimentation avec connecteur Ansi Mains lead AC Power cord with CEE 7 plug General safety instructionsPower cord with Ansi 73.11 plug ’Installation On Installation Page On Servicing On Cleaning Eclairage On illumination Safety Instructions On Repacking Unpacking Dimensions Battery Installation on the RCU Unpacking & Dimensions Unpacking Pull To open Projector dimensions Battery installation in the RCU Installation Guidelines Installation Guidelines Environment Installation guidelinesWhat about ambient light ? What image size? How big should the image be? Installation Guidelines Which screen type? Inputs and computer video format input compatibility Installation Guidelines Where to install the projector?Definitions of the Abbreviation on drawings Lens type selection Table mounting of the Barcographics Ceiling mounting of the Barcographics How to install the projector? Installation Guidelines How to install a projection lens? Installation SET UP Installation Set UpProjector configuration Rear/Ceilin g Rear/T ab l e Ro n t/Ceilin g Ro n t/T able Enter Location and Functions of Control Front panel terminology Local keypad Remote controlLocation and Function of Controls Front panel terminology Diagnostics code a source number Control Panel Terminology Remote controlLocal keypad Remote Control RCU Local keypad Control disk on RCU or + and keyscursor keys to Terminology Power Connection Power Connection Switching on Power mains cord connectionFuses Stand by button 980 h Switching to stand-by Switching off Input Module Connections ConnectionsPeripheral equipment connection Input module insertion into the projector Input connections DI a G no S TI CS Video/S-video input module Input Slots Straps on module level DI AG NOS TI CS RGB analog input module RGB input selection RGB-SOG= sync on green Sync Blue luma Luma Red luma Component input module Indication on the input slot menu Component input selection Input selection RGB3S/RG3sB input module Floating or non-floating input Red Strap yes non floating See Change Baudrate PC in chapter Service mode Set up of the baud rate for communication with a computer Connecting a VS05 to the projector Controlling Controlling Point the front of the RCU to the reflective screen surface How to use the RCU? How to control the projector or projectors Software set up of the projector addressUsing the RCU Projector address How to program an address into the RCU? How to display a projector address?Picture controls with direct access Brightness Control Contrast Control Phase ControlColor Saturation Sharpness Control Start UP of the Adjustment Mode Start Up of the Adjustment Mode Adjustment Mode Password Guided Adjustment Mode Guided Adjustment Mode Guided Adjustment Mode is not active Random Access Adjustment Mode Random Access Adjustment ModeFile Service Picture Tuning Geometry Starting up the Random Access Adjustment Mode File service Load file Edit Edit file Read Amds Options Press Exit to leave the Edit File Option menu Rename File Rename Copy File Copy Delete File Delete File Options Picture Tuning Still Video Sync slow/fast Color Balance Color Balance Gamma Shift Geometry Size Side keystone Blanking Blanking Options Options Installation InstallationConvergence Configuration Internal Patterns Starting up the Installation Mode Input Slots Convergence Convergence and press Enter to Green focusing Red on green convergence Barcographics 8200 12-7 Blue on green convergence Internal Patterns Configuration Service Mode Service Mode Service Starting up the Service Mode Barcographics 8200 13-3 13-4 Barcographics 8200 Software version Identification 13-6 Barcographics 8200 How to enable or disable the password function ? Change Password 13-8 Barcographics 8200 Change Language Service Mode How to change the password ? Change Baudrate PC Change Projector Address Service Reset Lamp Runtime Lamp Run Time History Panel Adjustments Panel Adjustments Preset Input Balance Preset Input Balance 60Hz Tracking Hz Tracking I2C Diagnosis I2C diagnosis Optional Equipment IR remote receiver Hardwired RCUOptional Equipment RCVDS05 IR Receiver VS05 Rcvds 800 / Rcvds D9-D9 communication cable Din Mini8-D9 adapter cable Projector Transport Handle Projector Frame for Dual or Triple Configurations Multifunctional flight case Features 14-8 Barcographics 8200 Standard source set up files Appendix a Standard Source Set Up Files MAC4 XGA75GS MAC6 Battery replacement in the RCU Appendix B Battery Replacement in the RCU Focusing the lens Appendix C Focusing the Lens Lens Cleaning Procedure Appendix D Lens Cleaning Procedure Appendix D Lens Cleaning Procedure Source numbers 90 Appendix E Source Number 90 Lenses Appendix F Lenses Lens formulas to calculate the projector distance Insert card RCU