Reference Description, AL1 | Bosch Appliances UPH-3D, UPH-2D, UPH-Z

20 en Connecting the Washer Pump (optional)High Speed Pan/Tilt System

Reference	Description

	Alarm input, voltage-controlled (10-35 V), to
	monitor the presence of water in the tank.
AL1	For devices with level sensors (HAC-WAS05-50,
AL1	HAC-WAS30-50), closure of the contact, if
	HAC-WAS30-50), closure of the contact, if
	enabled, generates an on-screen alarm (see
	Figure 11.3.5 to configure the alarm).

O1-C1	Clean contact for starting the water pump.

K1	Power relay (external), able to start the water
K1	pump.
	pump.

	Wiper power supply (max 24 Vac – 0.75 A from
	TR3 and TR4), from safety transformer housed
F1-F2	in the base of the device (factory fitted with
F1-F2	wiper option).
	wiper option).
	Note: Only required for UPH-Z Series; not
	required for UPH-2D or UPH-3D Series.

Fig. 5.5 Connecting the Washer System with Level Sensor Capabilities

NOTICE!

i The HAC-WAS05-10 washer system does not have a level sensor. Therefore, it is not necessary to connect the alarm input.

F01U.073.990 Version 1.0 2007.07

Instruction Manual

Bosch Security Systems

Page 20

Image 20

Bosch Appliances UPH-3D, UPH-2D, UPH-Z instruction manual Reference Description, AL1

Contents

High Speed Pan/Tilt System Page Table of Contents Configuring the System Safety Important safety instructions Safety precautions Important notices Coax grounding Copyright Trademarks Parts List 2UnpackingTools Required Small, straight-blade screwdriver 2.5 mm 0.1 Safety Rules 3Description Warranties are void Installing the High Speed Pan/TiltMounting the High Speed Pan/Tilt Description Outdoor Pole Mount for UPH SeriesOutdoor Wall Mount for UPH Series Pole Adapter for MTC-WUPH Reference # Description Base Gasket Screw Ring Washer Bracket Support Wiring the Video Cable Tie Threads used to Group and Secure Signal Cables Connecting the Power Supply That the disconnecting switch is openWire Color VAC Terminal Connection Per local Installer Neutral Live/Active Green/Yellow Earth 5RS-232 Wiring BiphaseRS-232 is used for firmware upgrades only see Figure Connecting the Washer Pump optional Washer Pipe NutNosecap Coupling Calibrating the Nozzle Reference Description AL1 Connecting the Peripherals Base with 19-pin Connector for Connecting Peripherals Metal Fixing Accessory Attaching the Top UnitSalt Bag Fixing Screws Aligning the Tabs Configuration Window Place safety label near unit that warns of moving partsScrew Screw Seal Configuring the Device Baud Rate SwitchesRocker for DIP switch No is OFF PROGRAM. OFF For updating the firmware Protocol Switches Setting the AddressProtocol Baud Rate Menu setup OSD Pelco D 2400 Preset Biphase Auto AUX-On Bilinx Address Combinations 4Connections RS-485 Divar Biphase RS-485 Biphase Bilinx/Video IntuikeyboardIntuikeyboard Allegiant RS485-2 EthernetEthernet Video To configure the UPH, proceed as follows Switching On and OffConfiguring the Device Using the Joystick On-screen Display OSDMoving Around the Menus Open or Iris Close button 10.1 Keyboard Commands List Setup and ConfigurationPresets Auxiliary Connections Configuring the System 10.2 Changing the Settings10.3 Changing the Numeric Fields Main menu by pressing AUX on 200 Enter Played on the screen 11.2 Display Setup Menu11.1 Language Menu Feature Description Default Options Enables / disables the on-screen message By the device Enables the user to edit a customized, onArea Parameters Menu Depending on the horizontal position reached Setting the Area Position Values Changing the Edit Text Menu Display Parameters Offset Pan Speed Menu Wiper-washer, and the alarm settings of the UPH11.3 Motion Parameters Menu Tilt Speed Data is expressed as degrees per secondPAN Speed Limits Preset/Patrol/Autopan Feature Description Preset Menu Special Preset Parameters Home Position Reached Speed Patrol loading of preset positions Start PositionEND Position First Prst Speed Motions Recall Menu Autopan menu is used to indicate preset position settingsAutopan Wiper-Washer Alarms 11.4 Camera Parameters UPH-2D and UPH-3D Series DinionXF Cameras UPH-Z Series camera module Zoom Parameters Menu Focus Parameters menu is used to enable focus settings Focus Parameters Menu Dynamic Masking UPH-Z Series only Parameters Mode Infrared MenuAuto Exposure Parameters Menu Mask NR Mask ChangingPosition Recall Changing Colour PTZ Mode Masking 11.5 Creating a New Dynamic Mask Image Stabilization Back Light CompenSAT 11.6 Load Default Configuration 11.7 Setup Info MenuLoad Default menu is used to load the default settings UPH boards Maintenance 12.1 Cleaning12.2 Replacing the Fuses Voltage Fuse F1 Fuse F2 Troubleshooting Error TroubleshootingProblem Possible Cause Solution 13.1 Dimensions and Range of Movement 514 584 R385 Technical Specifications Bosch Security Systems

Reference

Description

AL1

Figure 11.3.5 to configure the alarm).

O1-C1

Clean contact for starting the water pump.

Power relay (external), able to start the water

pump.

Wiper power supply (max 24 Vac – 0.75 A from

TR3 and TR4), from safety transformer housed

F1-F2

in the base of the device (factory fitted with

wiper option).

required for UPH-2D or UPH-3D Series.

Fig. 5.5 Connecting the Washer System with Level Sensor Capabilities