Address Combinations | Bosch Appliances UPH-2D, UPH-Z, UPH-3D

High Speed Pan/Tilt SystemConfiguring the Device en 27

7.3.1

Address Combinations

Fig. 7.2 Address table

Bosch Security Systems

Instruction Manual

F01U.073.990 Version 1.0 2007.07

Image 27

Bosch Appliances UPH-2D, UPH-Z, UPH-3D instruction manual Address Combinations

Contents

High Speed Pan/Tilt System Page Table of Contents Configuring the System Important safety instructions Safety Safety precautions Coax grounding Important notices Trademarks Copyright Small, straight-blade screwdriver 2.5 mm 0.1 Parts List2Unpacking Tools Required 3Description Safety Rules Installing the High Speed Pan/Tilt Mounting the High Speed Pan/TiltWarranties are void Pole Adapter for MTC-WUPH DescriptionOutdoor Pole Mount for UPH Series Outdoor Wall Mount for UPH Series Base Gasket Screw Ring Washer Bracket Support Reference # Description Tie Threads used to Group and Secure Signal Cables Wiring the Video Cable Per local Installer Neutral Live/Active Green/Yellow Earth Connecting the Power SupplyThat the disconnecting switch is open Wire Color VAC Terminal Connection Wiring Biphase RS-232 is used for firmware upgrades only see Figure5RS-232 Connecting the Washer Pump optional Coupling Washer PipeNut Nosecap Calibrating the Nozzle AL1 Reference Description Base with 19-pin Connector for Connecting Peripherals Connecting the Peripherals Fixing Screws Metal Fixing AccessoryAttaching the Top Unit Salt Bag Aligning the Tabs Screw Seal Configuration WindowPlace safety label near unit that warns of moving parts Screw For updating the firmware Configuring the DeviceBaud Rate Switches Rocker for DIP switch No is OFF PROGRAM. OFF Pelco D 2400 Preset Biphase Auto AUX-On Bilinx Protocol SwitchesSetting the Address Protocol Baud Rate Menu setup OSD Address Combinations 4Connections Allegiant RS-485 Divar BiphaseRS-485 Biphase Bilinx/Video Intuikeyboard Intuikeyboard EthernetEthernet Video RS485-2 Switching On and Off Configuring the DeviceTo configure the UPH, proceed as follows Open or Iris Close button Using the JoystickOn-screen Display OSD Moving Around the Menus Auxiliary Connections 10.1 Keyboard Commands ListSetup and Configuration Presets Main menu by pressing AUX on 200 Enter Configuring the System10.2 Changing the Settings 10.3 Changing the Numeric Fields 11.2 Display Setup Menu 11.1 Language MenuPlayed on the screen Feature Description Default Options Depending on the horizontal position reached Enables / disables the on-screen messageBy the device Enables the user to edit a customized, on Area Parameters Menu Changing the Edit Text Menu Setting the Area Position Values Offset Pan Display Parameters Wiper-washer, and the alarm settings of the UPH 11.3 Motion Parameters MenuSpeed Menu Data is expressed as degrees per second PAN SpeedTilt Speed Limits Feature Description Preset/Patrol/Autopan Preset Menu Special Preset Parameters Reached Speed Home Position First Prst Speed Patrol loading of preset positionsStart Position END Position Autopan menu is used to indicate preset position settings AutopanMotions Recall Menu Wiper-Washer 11.4 Camera Parameters Alarms UPH-2D and UPH-3D Series DinionXF Cameras Zoom Parameters Menu UPH-Z Series camera module Focus Parameters Menu Focus Parameters menu is used to enable focus settings Parameters Mode Infrared Menu Auto Exposure Parameters MenuDynamic Masking UPH-Z Series only Changing Colour Mask NRMask Changing Position Recall 11.5 Creating a New Dynamic Mask PTZ Mode Masking Back Light Compen SATImage Stabilization UPH boards 11.6 Load Default Configuration11.7 Setup Info Menu Load Default menu is used to load the default settings Voltage Fuse F1 Fuse F2 Maintenance12.1 Cleaning 12.2 Replacing the Fuses Troubleshooting Problem Possible Cause SolutionTroubleshooting Error 514 584 13.1 Dimensions and Range of Movement R385 Technical Specifications Bosch Security Systems