Connecting the Peripherals | Bosch Appliances UPH-2D, UPH-Z, UPH-3D

High Speed Pan/Tilt SystemConnecting the Washer Pump (optional) en 21

5.1

Connecting the Peripherals

The base has a 19-pin connector for which the following connections are illustrated:

Fig. 5.6 Base with 19-pin Connector for Connecting Peripherals

	Reference	Description

	RS-485-2	Dedicated communication port for Pelco D
	RS-485-2	(2400 baud, 8N1)
		(2400 baud, 8N1)

	Video	Composite video out 1 Vpp

	O1-C1 and	Clean output contacts that can be activated by
	O2-C2	alarm or by user (50 VDC or 30 VAC @ 1A)

	A1, A2, A3,	Alarm in, voltage-controlled (10-35 VDC),
	and A4	referred to common COM

	B+ and B-	Biphase communication lines

!

CAUTION! The system is TNV-1 type, do not connect to SELV circuits.

Bosch Security Systems

Instruction Manual

F01U.073.990 Version 1.0 2007.07

Image 21

Bosch Appliances UPH-2D, UPH-Z, UPH-3D Connecting the Peripherals, Base with 19-pin Connector for Connecting Peripherals

Contents

High Speed Pan/Tilt System Page Table of Contents Configuring the System Important safety instructions Safety Safety precautions Coax grounding Important notices Trademarks Copyright 2Unpacking Parts ListTools Required Small, straight-blade screwdriver 2.5 mm 0.1 3Description Safety Rules Installing the High Speed Pan/Tilt Mounting the High Speed Pan/TiltWarranties are void Outdoor Pole Mount for UPH Series DescriptionOutdoor Wall Mount for UPH Series Pole Adapter for MTC-WUPH Base Gasket Screw Ring Washer Bracket Support Reference # Description Tie Threads used to Group and Secure Signal Cables Wiring the Video Cable That the disconnecting switch is open Connecting the Power SupplyWire Color VAC Terminal Connection Per local Installer Neutral Live/Active Green/Yellow Earth Wiring Biphase RS-232 is used for firmware upgrades only see Figure5RS-232 Connecting the Washer Pump optional Nut Washer PipeNosecap Coupling Calibrating the Nozzle AL1 Reference Description Base with 19-pin Connector for Connecting Peripherals Connecting the Peripherals Attaching the Top Unit Metal Fixing AccessorySalt Bag Fixing Screws Aligning the Tabs Place safety label near unit that warns of moving parts Configuration WindowScrew Screw Seal Baud Rate Switches Configuring the DeviceRocker for DIP switch No is OFF PROGRAM. OFF For updating the firmware Setting the Address Protocol SwitchesProtocol Baud Rate Menu setup OSD Pelco D 2400 Preset Biphase Auto AUX-On Bilinx Address Combinations 4Connections RS-485 Biphase Bilinx/Video Intuikeyboard RS-485 Divar BiphaseIntuikeyboard Allegiant EthernetEthernet Video RS485-2 Switching On and Off Configuring the DeviceTo configure the UPH, proceed as follows On-screen Display OSD Using the JoystickMoving Around the Menus Open or Iris Close button Setup and Configuration 10.1 Keyboard Commands ListPresets Auxiliary Connections 10.2 Changing the Settings Configuring the System10.3 Changing the Numeric Fields Main menu by pressing AUX on 200 Enter 11.2 Display Setup Menu 11.1 Language MenuPlayed on the screen Feature Description Default Options By the device Enables the user to edit a customized, on Enables / disables the on-screen messageArea Parameters Menu Depending on the horizontal position reached Changing the Edit Text Menu Setting the Area Position Values Offset Pan Display Parameters Wiper-washer, and the alarm settings of the UPH 11.3 Motion Parameters MenuSpeed Menu Data is expressed as degrees per second PAN SpeedTilt Speed Limits Feature Description Preset/Patrol/Autopan Preset Menu Special Preset Parameters Reached Speed Home Position Start Position Patrol loading of preset positionsEND Position First Prst Speed Autopan menu is used to indicate preset position settings AutopanMotions Recall Menu Wiper-Washer 11.4 Camera Parameters Alarms UPH-2D and UPH-3D Series DinionXF Cameras Zoom Parameters Menu UPH-Z Series camera module Focus Parameters Menu Focus Parameters menu is used to enable focus settings Parameters Mode Infrared Menu Auto Exposure Parameters MenuDynamic Masking UPH-Z Series only Mask Changing Mask NRPosition Recall Changing Colour 11.5 Creating a New Dynamic Mask PTZ Mode Masking Back Light Compen SATImage Stabilization 11.7 Setup Info Menu 11.6 Load Default ConfigurationLoad Default menu is used to load the default settings UPH boards 12.1 Cleaning Maintenance12.2 Replacing the Fuses Voltage Fuse F1 Fuse F2 Troubleshooting Problem Possible Cause SolutionTroubleshooting Error 514 584 13.1 Dimensions and Range of Movement R385 Technical Specifications Bosch Security Systems