Load Default Configuration, UPH boards

58 en Configuring the SystemHigh Speed Pan/Tilt System

11.6	Load Default Configuration
	The Load Default menu is used to load the default settings.

	DEFAULT VALUES MENU
	1	- LOAD DEF. VALUES?	YES
	2	- DELETE ALL PRST?	NO

ATTENTION!!!

RELOAD ALL SETTINGS

EXCEPT FOR PRESETS

Fig. 11.29 Load Default Menu

DEFAULT VALUES MENU
1	- LOAD DEF. VALUES?	NO
2	- DELETE ALL PRST?	YES

ATTENTION!!!

CLEARS ONLY THE PRESETS

Fig. 11.30 Clear All Presets

11.7	Setup Info Menu
	The Setup Info menu is used to check the device configuration and the software versions of
	the UPH boards.

	SETUP INFO MENU
	NET board	:	MPP board:
	ver. BOSCH 1.7		ver. BOSCH 1.7
	Apr. 27 2007		Apr. 27 2007
	HD r.2		HD r.2
	Protocol	:	BOSCH
	Baudrate	:	38400
	Address	:	00001
	Enabled RS485	:	TX-RX
	FWInt 01.03		FWCam: 01.00

Fig. 11.31 Setup Info Menu

F01U.073.990 Version 1.0 2007.07

Instruction Manual

Bosch Security Systems

Page 58

Image 58

Bosch Appliances UPH-Z Load Default Configuration, Setup Info Menu, Load Default menu is used to load the default settings

Contents

High Speed Pan/Tilt System Page Table of Contents Configuring the System Safety Important safety instructions Safety precautions Important notices Coax grounding Copyright Trademarks Tools Required Parts List2Unpacking Small, straight-blade screwdriver 2.5 mm 0.1 Safety Rules 3Description Mounting the High Speed Pan/Tilt Installing the High Speed Pan/TiltWarranties are void Outdoor Wall Mount for UPH Series DescriptionOutdoor Pole Mount for UPH Series Pole Adapter for MTC-WUPH Reference # Description Base Gasket Screw Ring Washer Bracket Support Wiring the Video Cable Tie Threads used to Group and Secure Signal Cables Wire Color VAC Terminal Connection Connecting the Power SupplyThat the disconnecting switch is open Per local Installer Neutral Live/Active Green/Yellow Earth RS-232 is used for firmware upgrades only see Figure Wiring Biphase5RS-232 Connecting the Washer Pump optional Nosecap Washer PipeNut Coupling Calibrating the Nozzle Reference Description AL1 Connecting the Peripherals Base with 19-pin Connector for Connecting Peripherals Salt Bag Metal Fixing AccessoryAttaching the Top Unit Fixing Screws Aligning the Tabs Screw Configuration WindowPlace safety label near unit that warns of moving parts Screw Seal Rocker for DIP switch No is OFF PROGRAM. OFF Configuring the DeviceBaud Rate Switches For updating the firmware Protocol Baud Rate Menu setup OSD Protocol SwitchesSetting the Address Pelco D 2400 Preset Biphase Auto AUX-On Bilinx Address Combinations 4Connections Intuikeyboard RS-485 Divar BiphaseRS-485 Biphase Bilinx/Video Intuikeyboard Allegiant RS485-2 EthernetEthernet Video Configuring the Device Switching On and OffTo configure the UPH, proceed as follows Moving Around the Menus Using the JoystickOn-screen Display OSD Open or Iris Close button Presets 10.1 Keyboard Commands ListSetup and Configuration Auxiliary Connections 10.3 Changing the Numeric Fields Configuring the System10.2 Changing the Settings Main menu by pressing AUX on 200 Enter 11.1 Language Menu 11.2 Display Setup MenuPlayed on the screen Feature Description Default Options Area Parameters Menu Enables / disables the on-screen messageBy the device Enables the user to edit a customized, on Depending on the horizontal position reached Setting the Area Position Values Changing the Edit Text Menu Display Parameters Offset Pan 11.3 Motion Parameters Menu Wiper-washer, and the alarm settings of the UPHSpeed Menu PAN Speed Data is expressed as degrees per secondTilt Speed Limits Preset/Patrol/Autopan Feature Description Preset Menu Special Preset Parameters Home Position Reached Speed END Position Patrol loading of preset positionsStart Position First Prst Speed Autopan Autopan menu is used to indicate preset position settingsMotions Recall Menu Wiper-Washer Alarms 11.4 Camera Parameters UPH-2D and UPH-3D Series DinionXF Cameras UPH-Z Series camera module Zoom Parameters Menu Focus Parameters menu is used to enable focus settings Focus Parameters Menu Auto Exposure Parameters Menu Parameters Mode Infrared MenuDynamic Masking UPH-Z Series only Position Recall Mask NRMask Changing Changing Colour PTZ Mode Masking 11.5 Creating a New Dynamic Mask SAT Back Light CompenImage Stabilization Load Default menu is used to load the default settings 11.6 Load Default Configuration11.7 Setup Info Menu UPH boards 12.2 Replacing the Fuses Maintenance12.1 Cleaning Voltage Fuse F1 Fuse F2 Problem Possible Cause Solution TroubleshootingTroubleshooting Error 13.1 Dimensions and Range of Movement 514 584 R385 Technical Specifications Bosch Security Systems

Bosch Appliances UPH-Z, UPH-2D, UPH-3D Load Default Configuration, Setup Info Menu, UPH boards

Models: UPH-Z UPH-2D UPH-3D

11.6

Load Default Configuration

The Load Default menu is used to load the default settings.

Fig. 11.29 Load Default Menu

Fig. 11.30 Clear All Presets

11.7

Setup Info Menu

the UPH boards.

Fig. 11.31 Setup Info Menu

F01U.073.990 Version 1.0 2007.07

Bosch Security Systems