R385 | Bosch Appliances UPH-3D, UPH-2D, UPH-Z specification

62 en Troubleshooting	High Speed Pan/Tilt System

514 (20.24)
40º
-
90º
R350
(13.
78)
724 (28.50)
73
(2.87)
(14.72)374
R385
(15
.
16)

Fig. 13.1 Dimensions and Range of Movement

F01U.073.990 Version 1.0 2007.07

Instruction Manual

Bosch Security Systems

Image 62

Bosch Appliances UPH-3D, UPH-2D, UPH-Z instruction manual R385

Contents

High Speed Pan/Tilt System Page Table of Contents Configuring the System Safety Important safety instructions Safety precautions Important notices Coax grounding Copyright Trademarks Tools Required Parts List2Unpacking Small, straight-blade screwdriver 2.5 mm 0.1 Safety Rules 3Description Warranties are void Installing the High Speed Pan/TiltMounting the High Speed Pan/Tilt Outdoor Wall Mount for UPH Series DescriptionOutdoor Pole Mount for UPH Series Pole Adapter for MTC-WUPH Reference # Description Base Gasket Screw Ring Washer Bracket Support Wiring the Video Cable Tie Threads used to Group and Secure Signal Cables Wire Color VAC Terminal Connection Connecting the Power SupplyThat the disconnecting switch is open Per local Installer Neutral Live/Active Green/Yellow Earth 5RS-232 Wiring BiphaseRS-232 is used for firmware upgrades only see Figure Connecting the Washer Pump optional Nosecap Washer PipeNut Coupling Calibrating the Nozzle Reference Description AL1 Connecting the Peripherals Base with 19-pin Connector for Connecting Peripherals Salt Bag Metal Fixing AccessoryAttaching the Top Unit Fixing Screws Aligning the Tabs Screw Configuration WindowPlace safety label near unit that warns of moving parts Screw Seal Rocker for DIP switch No is OFF PROGRAM. OFF Configuring the DeviceBaud Rate Switches For updating the firmware Protocol Baud Rate Menu setup OSD Protocol SwitchesSetting the Address Pelco D 2400 Preset Biphase Auto AUX-On Bilinx Address Combinations 4Connections Intuikeyboard RS-485 Divar BiphaseRS-485 Biphase Bilinx/Video Intuikeyboard Allegiant RS485-2 EthernetEthernet Video To configure the UPH, proceed as follows Switching On and OffConfiguring the Device Moving Around the Menus Using the JoystickOn-screen Display OSD Open or Iris Close button Presets 10.1 Keyboard Commands ListSetup and Configuration Auxiliary Connections 10.3 Changing the Numeric Fields Configuring the System10.2 Changing the Settings Main menu by pressing AUX on 200 Enter Played on the screen 11.2 Display Setup Menu11.1 Language Menu Feature Description Default Options Area Parameters Menu Enables / disables the on-screen messageBy the device Enables the user to edit a customized, on Depending on the horizontal position reached Setting the Area Position Values Changing the Edit Text Menu Display Parameters Offset Pan Speed Menu Wiper-washer, and the alarm settings of the UPH11.3 Motion Parameters Menu Tilt Speed Data is expressed as degrees per secondPAN Speed Limits Preset/Patrol/Autopan Feature Description Preset Menu Special Preset Parameters Home Position Reached Speed END Position Patrol loading of preset positionsStart Position First Prst Speed Motions Recall Menu Autopan menu is used to indicate preset position settingsAutopan Wiper-Washer Alarms 11.4 Camera Parameters UPH-2D and UPH-3D Series DinionXF Cameras UPH-Z Series camera module Zoom Parameters Menu Focus Parameters menu is used to enable focus settings Focus Parameters Menu Dynamic Masking UPH-Z Series only Parameters Mode Infrared MenuAuto Exposure Parameters Menu Position Recall Mask NRMask Changing Changing Colour PTZ Mode Masking 11.5 Creating a New Dynamic Mask Image Stabilization Back Light CompenSAT Load Default menu is used to load the default settings 11.6 Load Default Configuration11.7 Setup Info Menu UPH boards 12.2 Replacing the Fuses Maintenance12.1 Cleaning Voltage Fuse F1 Fuse F2 Troubleshooting Error TroubleshootingProblem Possible Cause Solution 13.1 Dimensions and Range of Movement 514 584 R385 Technical Specifications Bosch Security Systems