Route Switch Processor, WS-X6K-S2-MSFC2 | Cisco Systems 7600

Chapter 2 Route Switch Processors and Supervisor Engines

Route Switch Processor 720

Table 2-1 Route Switch Processor and Supervisor Engine Configurations (continued)

Product Number	Description
WS-X6K-S2-MSFC2	•	Two dual-port 1000BASE-X GBIC uplinks, 16-MB bootflash,
		128-MB DRAM on supervisor engine and 128 MB on MSFC2
	•	PFC2 and MSFC2
	• Fabric enabled to support optional switch fabric module (SFM2)
	• QoS port architecture (Rx/Tx): 1p1q4t/1p2q2t

WS-X6K-S2U-MSFC2	•	Two dual-port 1000BASE-X GBIC uplinks, 32-MB bootflash,
		256-MB DRAM on supervisor engine and 256 MB on MSFC2
	•	PFC2 and MSFC2
	• Fabric enabled to support optional SFM2
	• QoS port architecture (Rx/Tx): 1p1q4t/1p2q2t

WS-X6K-S2-PFC2	•	Two dual-port 1000BASE-X GBIC uplinks
	• PFC2; fabric enabled, supports optional SFM2
	• QoS port architecture (Rx/Tx): 1p1q4t/1p2q2t

WS-X6500-SFM2	•	(Optional) SFM2

Note The Sup2 is not supported in Cisco IOS Release 12.2SRA and later releases.

Route Switch Processor 720

This section describes the Route Switch Processor 720 (RSP720). The Cisco 7600 RSP720 consists of a full-size board and two integrated daughter cards: the MSFC4 and a PFC3C or PFC3CXL. The RSP720 has an integrated switch fabric that interconnects all of the line cards in the Cisco 7600 router with point-to-point 20-Gbps full-duplex serial channels.

Note	• Cisco IOS Release 12.2SRB and later releases support the RSP720; earlier releases do not.
	The RSP720 is supported on all Cisco 7600 routers (including enhanced chassis) except the Cisco
	7603 and the Cisco OSR-7609.
	• Cisco IOS Release 12.2SRC and later releases support an RSP720 that has 10GE uplinks
	(RSP720-3C-10GE and RSP720-3CXL-10GE). See the “RSP720 with 10GE Uplink Ports” section
	on page 2-8for more information.

	Figure 2-1shows the RSP720-3C-GE front panel, which is the same as the RSP720-3CXL-GE front
	panel. See Table 2-2and Table 2-3for information about the front-panel controls and LEDs.

Cisco 7600 Series Router Supervisor Engine and Route Switch Processor Guide

2-6	OL-10100-04

Image 22

Cisco Systems 7600 manual Route Switch Processor, WS-X6K-S2-MSFC2, WS-X6K-S2U-MSFC2, WS-X6K-S2-PFC2

Contents

Americas Headquarters Text Part Number OL-10100-04 Copyright 2007-2008 Cisco Systems, Inc. All rights reserved N T E N T S Safety Precautions for Module Installation and Removal Cleaning the Fiber-Optic Connectors B-15 OL-10100-04 Contents Document History Chapter Title Description Document OrganizationDocument Conventions Convention Description Related Documentation OL-10100-04 Cisco 7600 Product Overview Cisco 7600 Series Routers Supported Hardware Features Feature Description Feature Description Port Addresses Physical Interface Addresses MAC Addresses FAN Status Route Switch Processors Supervisor Engines Overview Product Number Description Product Number RSP720-3CXL-GE WS-SUP720-3BXL WS-SUP32-GE-3B WS-X6K-S2U-MSFC2 Route Switch ProcessorWS-X6K-S2-MSFC2 WS-X6K-S2-PFC2 Unsupported Hardware and Features RSP720 FeaturesSupported Chassis, Line Cards, and Modules RSP720-10GE Features RSP720 with 10GE Uplink Ports Unsupported Features Unsupported Chassis and Modules RSP720-10GE Usage Guidelines and Limitations QoS on the RSP720-10GE QoS Configuration Guidelines Supervisor Engine 720 and Supervisor Engine Front-Panel Controls RSP720, RSP720-10GE, Sup720, Sup32 Component Description Front-Panel LEDs RSP720, RSP720-10GE, Sup720, Sup32Color Description Supervisor Engine Supervisor Engine 2 Front Panel Section on page 3-10 for more information Off when you insert a card Preparing for Installation or Removal Safety Precautions for Module Installation and Removal Preventing Electrostatic Discharge Damage Determining Module Location Tools Required for Module InstallationModule Slot Assignments Installing a Supervisor Engine or Route Switch Processor Module Ejector Levers and Captive Installation Screws See Figure Removing a Supervisor Engine or Route Switch Processor Hot Swapping OIR Modules Removing and Replacing Memory Connecting to the Console Port Connecting a Terminal Connecting a Modem Connecting to the Uplink PortsSupervisor Engine Module Uplink Ports Using Flash Memory Cards Locating the Flash PC Card Write-Protection Switch Installing a Flash Memory Card Determining Software Feature Support Power Management and Environmental MonitoringRemoving a Flash Memory Card Specification Module SpecificationsRegulatory Standards Compliance OL-10100-04 Cable and Connector Specifications Limiting Connection Distances Uplink Port Transceiver Modules Transceiver Module Part Numbers 1GE Uplink Ports and Cabling Specifications Product ID Description MMF SMF 10GE Uplink Ports and Cabling Specifications SMF ITU-T Console Port Cabling Specifications Console Port Cabling Specifications and PinoutsGbic Module Cabling Specifications MHz km Micron Console Port Signals and Pinouts Rate bps Distance feet Distance meters Rollover Cable Signal RJ-45 Pin DB-9 PinRJ-45-to-RJ-45 RJ-45-to-DB-9 Console Device RJ-45-to-RJ-45 RJ-45-to-DB-25 Rollover Cable Modem Adapter Signal RJ-45 Pin DB-25 PinRJ-45-to-DB-25 Terminal Console RTS DTR Console Port Mode 2 Signaling and Pinouts Sup2 Only RJ-45 ConnectorConsole Port Console Device Side 2 Pin Signal RD+ TD+ Not used SC Connectors Fiber-Optic ConnectorsSide 1 Pin Signal Side 2 Pin Signal MT-RJ Connectors Figure B-5 SC Optical Connector LC Connectors Figure B-7 LC Fiber-Optic Connector Cleaning the Fiber-Optic Connectors LX/LH Gbic and MMF Cable Considerations Patch Cord Patch Cord Installation OL-10100-04 Active LED MAC GBICs, connecting to Gigabit Ethernet cables Active Console PWR Mgmt LED Link LEDLX/LH Gbic Nvram Status LED System LED