Features, Feature Description | Cisco Systems 7600 specs

Chapter 1 Cisco 7600 Product Overview

Cisco 7600 Series Routers

Features

Table 1-1lists some key features of the Cisco 7600 series routers.

Table 1-1 Cisco 7600 Series Routers Key Features

	Feature	Description

	Performance and	For detailed information about the features supported on Cisco 7600 series
	configuration	routers, see the Cisco 7600 Series Router Cisco IOS Software Configuration
		Guide for the version of software being used on the router.

	Supervisor engine or	• Modular, upgradable feature modules for core switching logic
	route switch	• Modular Gigabit Ethernet ports that you can configure with Gigabit
	processor
	processor		Interface Converter (GBIC), small form-factor pluggable (SFP), XENPAK,

			and X2 optics modules
		• Several combinations of multilayer switch feature cards (MSFCs) and
			policy feature cards (PFCs) supported (see Table 2-1):
			– MSFC4 and PFC3C or PFC3CXL (for the RSP720, see note below)
			– MSFC3 and PFC3B, PFC3BXL, or PFC3A (see note below)
			– MSFC2 and PFC or PFC2
		• The MSFC contains the switch processor and route processor (SP/RP) for
			the router.
		•	PCMCIA slot
		• Console port for terminal and modem access
		Note The Route Switch Processor 720 (RSP720) is the newest supervisor
			engine for the Cisco 7600 series routers. It is available in Cisco IOS
			Release 12.2SRB and later releases.
		Note Cisco IOS Release 12.2SRC introduces support for the RSP720-10GE
			(an RSP with 10 Gigabit Ethernet uplink ports).
		Note Cisco IOS Release 12.2SXF is the last release in which the PFC3A is
			supported. Later releases do not support this PFC.

	Fault tolerance and	• Support for two hot-swappable (redundant) supervisor engines or route
	redundancy		switch processors, including fast switchover to the redundant (standby)
			module
		• Support for two redundant AC- or DC-input, load-sharing power supplies
		• Support for two redundant AC- or DC-input PEMs (Cisco 7603 and
			Cisco 7606 routers only)
		• Power management for modules and power supplies
		• Environmental monitoring of critical system components
		• Hot-swappable fan assembly
		•	Redundant clock modules
		• LACP 1-1 redundancy with fast switchover

Cisco 7600 Series Router Supervisor Engine and Route Switch Processor Guide

	OL-10100-04	1-3

Image 13

Cisco Systems 7600 manual Features, Feature Description

Contents

Text Part Number OL-10100-04 Americas Headquarters Copyright 2007-2008 Cisco Systems, Inc. All rights reserved N T E N T S Safety Precautions for Module Installation and Removal Cleaning the Fiber-Optic Connectors B-15 OL-10100-04 Document History Contents Document Conventions Document OrganizationChapter Title Description Convention Description Related Documentation OL-10100-04 Cisco 7600 Series Routers Cisco 7600 Product Overview Supported Hardware Feature Description Features Feature Description Physical Interface Addresses Port Addresses FAN Status MAC Addresses Route Switch Processors Supervisor Engines Overview Product Number Description RSP720-3CXL-GE Product Number WS-SUP32-GE-3B WS-SUP720-3BXL WS-X6K-S2-MSFC2 Route Switch ProcessorWS-X6K-S2U-MSFC2 WS-X6K-S2-PFC2 Unsupported Hardware and Features RSP720 FeaturesSupported Chassis, Line Cards, and Modules RSP720 with 10GE Uplink Ports RSP720-10GE Features Unsupported Chassis and Modules Unsupported Features QoS on the RSP720-10GE RSP720-10GE Usage Guidelines and Limitations QoS Configuration Guidelines Front-Panel Controls RSP720, RSP720-10GE, Sup720, Sup32 Supervisor Engine 720 and Supervisor Engine Component Description Front-Panel LEDs RSP720, RSP720-10GE, Sup720, Sup32Color Description Supervisor Engine 2 Front Panel Supervisor Engine Section on page 3-10 for more information Off when you insert a card Preparing for Installation or Removal Preventing Electrostatic Discharge Damage Safety Precautions for Module Installation and Removal Determining Module Location Tools Required for Module InstallationModule Slot Assignments Module Installing a Supervisor Engine or Route Switch Processor Ejector Levers and Captive Installation Screws See Figure Removing a Supervisor Engine or Route Switch Processor Removing and Replacing Memory Hot Swapping OIR Modules Connecting a Terminal Connecting to the Console Port Connecting a Modem Connecting to the Uplink PortsSupervisor Engine Module Uplink Ports Locating the Flash PC Card Write-Protection Switch Using Flash Memory Cards Installing a Flash Memory Card Determining Software Feature Support Power Management and Environmental MonitoringRemoving a Flash Memory Card Specification Module SpecificationsRegulatory Standards Compliance OL-10100-04 Limiting Connection Distances Cable and Connector Specifications Transceiver Module Part Numbers Uplink Port Transceiver Modules Product ID Description 1GE Uplink Ports and Cabling Specifications SMF MMF SMF ITU-T 10GE Uplink Ports and Cabling Specifications Gbic Module Cabling Specifications Console Port Cabling Specifications and PinoutsConsole Port Cabling Specifications MHz km Micron Rate bps Distance feet Distance meters Console Port Signals and Pinouts RJ-45-to-RJ-45 RJ-45-to-DB-9 Console Signal RJ-45 Pin DB-9 PinRollover Cable Device RJ-45-to-DB-25 Terminal Console Rollover Cable Modem Adapter Signal RJ-45 Pin DB-25 PinRJ-45-to-RJ-45 RJ-45-to-DB-25 RTS DTR Console Port Mode 2 Signaling and Pinouts Sup2 Only RJ-45 ConnectorConsole Port Console Device RD+ TD+ Not used Side 2 Pin Signal SC Connectors Fiber-Optic ConnectorsSide 1 Pin Signal Side 2 Pin Signal Figure B-5 SC Optical Connector MT-RJ Connectors Figure B-7 LC Fiber-Optic Connector LC Connectors Cleaning the Fiber-Optic Connectors Patch Cord LX/LH Gbic and MMF Cable Considerations Patch Cord Installation OL-10100-04 MAC Active LED Active Console GBICs, connecting to Gigabit Ethernet cables LX/LH Gbic Link LEDPWR Mgmt LED Nvram System LED Status LED