Manuals / Cisco Systems / Computer Equipment / Switch

Cisco Systems 7600 manual Patch Cord Installation, B-17

Models: 7600

1 70

Download 70 pages 32.94 Kb

Page 65

Image 65

Appendix B Cable and Connector Specifications

LX/LH GBIC and MMF Cable Considerations

Patch Cord Installation

Warning Invisible laser radiation may be emitted from disconnected fibers or connectors. Do not stare into beams or view directly with optical instruments. Statement 1051

Plug the end of the patch cord labeled “To Equipment” into the GBIC (see Figure B-9). Plug the end labeled “To Cable Plant” into the patch panel. The patch cord is 9.84 feet (3 meters) long and has duplex SC male connectors at each end.

Figure B-9 Patch Cord Installation

	To equipment			To cable plant

13089

	Cisco 7600 Series Router Supervisor Engine and Route Switch Processor Guide

OL-10100-04		B-17
OL-10100-04		B-17

Page 65

Image 65

Cisco Systems 7600 manual Patch Cord Installation, B-17

Contents

Cisco 7600 Series Router Supervisor Engine and Route Switch Processor GuideJanuary Cisco Systems, Inc 170 West Tasman Drive San Jose, CATurn the television or radio antenna until the interference stops Unsupported Hardware and Features FeaturesC O N T E N T S PrefaceTools Required for Module Installation Safety Precautions for Module Installation and RemovalDetermining Software Feature Support Console Port Signals and Pinouts B-7Patch Cord Installation B-17 Cleaning the Fiber-Optic Connectors B-15RJ-45 Connector Fiber-Optic ConnectorsOL-10100-04 ContentsPreface ContentsDocument History Document History, page Document Organization, pageInstalling and Configuring Route Switch ProcessorsTechnical Specifications Cable and ConnectorCisco 7609 Router Installation Guide OSR-7609 Cisco 7600 Series Router Installation GuideCisco 7600 Series Router Module Installation Guide Cisco 7600 Series Router Cisco IOS Command ReferenceObtaining Documentation, Obtaining Support, and Security Guidelines Cisco 7600 Series Routers Cisco 7600 Product OverviewC H A P T E R Cisco 7600 Series Routers, page Port Addresses, pageSupported Hardware Table 1-1 Cisco 7600 Series Routers Key Features FeaturesMemory Physical Interface Addresses Port AddressesFigure 1-1 Cisco 7609 Router Port Address Examples MAC AddressesOverview, page Route Switch Processor 720, page Route Switch Processors and Supervisor EnginesRSP720 with 10GE Uplink Ports, page Supervisor Engine 720 and Supervisor Engine 32, pageOverview Route Switch Processor Table 2-1 Route Switch Processor and Supervisor Engine ConfigurationsSupervisor Engine Description Product NumberDescription Route Switch ProcessorProduct Number Supported Chassis, Line Cards, and Modules RSP720 FeaturesUnsupported Hardware and Features RSP720 with 10GE Uplink Ports RSP720-10GE FeaturesUnsupported Chassis and Modules Unsupported FeaturesSupported Chassis, Line Cards, and Modules 2-10 RSP720-10GE Usage Guidelines and LimitationsQoS on the RSP720-10GE Configuring 10GE Only QoS QoS Configuration Guidelines8q8t/1p7q8t CoS 16q8t/1p15q8t DSCP 16q1t/1p15q1t VLAN mls qos supervisor 10g-only no mls qos supervisor 10g-only2-12 Supervisor Engine 720 and Supervisor EngineFront-Panel Controls RSP720, RSP720-10GE, Sup720, Sup32 “Connecting to the Uplink Ports” section on page 3-10 for more See the “Connecting to the Console Port” section on page 3-9 forFront-Panel LEDs RSP720, RSP720-10GE, Sup720, Sup32 2-132-14 Supervisor EngineACTIVE PWR MGMT2-15 section on page 3-10 for more informationSupervisor Engine 2 Front-Panel Controls Supervisor Engine 2 LEDsSupervisor Engine 2 LEDs continued 2-16Preparing for Installation or Removal Installing and Configuring Route SwitchPreparing for Installation or Removal, page Installing a Supervisor Engine or Route Switch Processor, pagePreventing Electrostatic Discharge Damage Safety Precautions for Module Installation and RemovalDetermining Module Location Tools Required for Module InstallationSlot Assignments Installing a Supervisor Engine or Route Switch ProcessorInstalling a Supervisor Engine or Route Switch Processor Figure 3-1 Ejector Levers and Captive Installation ScrewsCaptive Ejector lever installation screws Figure 3-2 Positioning the Module in the SlotStep 8 Tighten the two captive installation screws on the module See FigureRemoving a Supervisor Engine or Route Switch Processor Removing and Replacing Memory Hot Swapping OIR ModulesConnecting a Terminal Connecting to the Console Port3-10 Connecting to the Uplink PortsConnecting a Modem Table 3-2 Route Switch Processor and Supervisor Engine Uplink Ports 3-11Module Uplink Ports3-12 Using Flash Memory Cards3-13 Installing a Flash Memory CardRSP720 and RSP720-10GE Flash Memory Cards Sup720 and Sup32 Flash Memory CardsDetermining Software Feature Support Power Management and Environmental MonitoringConfiguring a Supervisor Engine or Route Switch Processor Removing a Flash Memory CardModule Specifications Technical SpecificationsRegulatory Standards Compliance A P P E N D I X AOL-10100-04 Appendix A Technical Specifications Regulatory Standards ComplianceConsole Port Cabling Specifications and Pinouts, page B-6 Cable and Connector SpecificationsRJ-45 Connector, page B-10 Fiber-Optic Connectors, page B-12 Limiting Connection DistancesTransceiver Module Part Numbers Uplink Port Transceiver Modules1GE Uplink Ports and Cabling Specifications Table B-2 1GE Cabling Specifications1GE SFP Transceiver Modules continued Table B-310GE Uplink Ports and Cabling Specifications GBIC Module Cabling Specifications Console Port Cabling Specifications and PinoutsConsole Port Cabling Specifications Console Port Cabling Specifications, page B-6Identifying a Rollover Cable Console Port Signals and PinoutsDB-9 Adapter for Connecting to a PC Modem Adapter DB-25 Adapter for Connecting to a TerminalB-10 RJ-45 ConnectorConsole Port Mode 2 Signaling and Pinouts Sup2 Only Side 2 Pin Signal B-11SC Connectors Fiber-Optic ConnectorsSC Connectors, page B-12 MT-RJ Connectors, page B-13 LC Connectors, page B-14B-13 MT-RJ ConnectorsB-14 LC ConnectorsB-15 Cleaning the Fiber-Optic ConnectorsLX/LH GBIC and MMF Cable Considerations Patch Cord Configuration ExamplePatch Cord B-16B-17 Patch Cord InstallationAppendix B Cable and Connector Specifications B-18LX/LH GBIC and MMF Cable Considerations OL-10100-04IN-1 SymbolsI N D E Gigabit Ethernet cables IN-2GBICs, connecting to IN-3 IN-4