OL-10100-04 | Cisco Systems 7600 instruction

Appendix B Cable and Connector Specifications

LX/LH GBIC and MMF Cable Considerations

	Cisco 7600 Series Router Supervisor Engine and Route Switch Processor Guide
B-18	OL-10100-04

Image 66

Cisco Systems 7600 manual OL-10100-04

Contents

Americas Headquarters Text Part Number OL-10100-04 Copyright 2007-2008 Cisco Systems, Inc. All rights reserved N T E N T S Safety Precautions for Module Installation and Removal Cleaning the Fiber-Optic Connectors B-15 OL-10100-04 Contents Document History Chapter Title Description Document OrganizationDocument Conventions Convention Description Related Documentation OL-10100-04 Cisco 7600 Product Overview Cisco 7600 Series Routers Supported Hardware Features Feature Description Feature Description Port Addresses Physical Interface Addresses MAC Addresses FAN Status Route Switch Processors Supervisor Engines Overview Product Number Description Product Number RSP720-3CXL-GE WS-SUP720-3BXL WS-SUP32-GE-3B WS-X6K-S2U-MSFC2 Route Switch ProcessorWS-X6K-S2-MSFC2 WS-X6K-S2-PFC2 RSP720 Features Unsupported Hardware and FeaturesSupported Chassis, Line Cards, and Modules RSP720-10GE Features RSP720 with 10GE Uplink Ports Unsupported Features Unsupported Chassis and Modules RSP720-10GE Usage Guidelines and Limitations QoS on the RSP720-10GE QoS Configuration Guidelines Supervisor Engine 720 and Supervisor Engine Front-Panel Controls RSP720, RSP720-10GE, Sup720, Sup32 Front-Panel LEDs RSP720, RSP720-10GE, Sup720, Sup32 Component DescriptionColor Description Supervisor Engine Supervisor Engine 2 Front Panel Section on page 3-10 for more information Off when you insert a card Preparing for Installation or Removal Safety Precautions for Module Installation and Removal Preventing Electrostatic Discharge Damage Tools Required for Module Installation Determining Module LocationModule Slot Assignments Installing a Supervisor Engine or Route Switch Processor Module Ejector Levers and Captive Installation Screws See Figure Removing a Supervisor Engine or Route Switch Processor Hot Swapping OIR Modules Removing and Replacing Memory Connecting to the Console Port Connecting a Terminal Connecting to the Uplink Ports Connecting a ModemSupervisor Engine Module Uplink Ports Using Flash Memory Cards Locating the Flash PC Card Write-Protection Switch Installing a Flash Memory Card Power Management and Environmental Monitoring Determining Software Feature SupportRemoving a Flash Memory Card Module Specifications SpecificationRegulatory Standards Compliance OL-10100-04 Cable and Connector Specifications Limiting Connection Distances Uplink Port Transceiver Modules Transceiver Module Part Numbers 1GE Uplink Ports and Cabling Specifications Product ID Description MMF SMF 10GE Uplink Ports and Cabling Specifications SMF ITU-T Console Port Cabling Specifications Console Port Cabling Specifications and PinoutsGbic Module Cabling Specifications MHz km Micron Console Port Signals and Pinouts Rate bps Distance feet Distance meters Rollover Cable Signal RJ-45 Pin DB-9 PinRJ-45-to-RJ-45 RJ-45-to-DB-9 Console Device RJ-45-to-RJ-45 RJ-45-to-DB-25 Rollover Cable Modem Adapter Signal RJ-45 Pin DB-25 PinRJ-45-to-DB-25 Terminal Console RTS DTR RJ-45 Connector Console Port Mode 2 Signaling and Pinouts Sup2 OnlyConsole Port Console Device Side 2 Pin Signal RD+ TD+ Not used Fiber-Optic Connectors SC ConnectorsSide 1 Pin Signal Side 2 Pin Signal MT-RJ Connectors Figure B-5 SC Optical Connector LC Connectors Figure B-7 LC Fiber-Optic Connector Cleaning the Fiber-Optic Connectors LX/LH Gbic and MMF Cable Considerations Patch Cord Patch Cord Installation OL-10100-04 Active LED MAC GBICs, connecting to Gigabit Ethernet cables Active Console PWR Mgmt LED Link LEDLX/LH Gbic Nvram Status LED System LED