Using Flash Memory Cards | Cisco Systems 7600 guide

Chapter 3 Installing and Configuring Route Switch Processors and Supervisor Engines

Using Flash Memory Cards

Note	•	If two RSPs or supervisor engines are installed, the uplink ports on the redundant (standby) module
		are active and can be used for normal traffic like any other ports in the chassis.
	•	In Cisco IOS Release 12.2SRC, the uplink ports on a standby RSP720-10GE are not active and
		cannot be used for normal traffic.

Using Flash Memory Cards

The front panel on the supervisor engine or route switch processor has one or two disk slots for flash memory cards. You can insert a Flash PC, CompactFlash, or MicroDrive memory card in the slot and use the card to store and run software images and configuration files or to serve as an I/O device.

See Table 3-3for memory options.

•The Route Switch Processor 720 with 10-GE uplink ports (RSP720-10GE) has a single disk slot (labeled DISK 0) that accepts CompactFlash cards.

•The Route Switch Processor 720 and Supervisor Engine 720 have two disk slots:

–DISK 0 accepts a CompactFlash card only.

–DISK 1 accepts either a CompactFlash card or a 1-GB MicroDrive.

•The Supervisor Engine 32 has a single slot (labeled DISK 0) that accepts CompactFlash cards and IBM MicroDrive cards.

•The Supervisor Engine 2 has a single slot (labeled PCMCIA) that accepts PCMCIA cards.

Note You can insert and remove a flash memory card with the power on. Before you install a card, verify that the card is set with write protection off. The write-protection switch is located on the front edge of the card (when the printing is right side up and the edge connector end is away from you). (See Figure 3-5.)

Figure 3-5 Locating the Flash PC Card Write-Protection Switch

	Flash PC card
Flash PC card	shown with write
write protection	protection off

H2352

Flash PC card

Note Not all flash memory cards have a write-protection switch.

	Cisco 7600 Series Router Supervisor Engine and Route Switch Processor Guide
3-12	OL-10100-04

Image 44

Cisco Systems 7600 manual Using Flash Memory Cards, Locating the Flash PC Card Write-Protection Switch

Contents

Americas Headquarters Text Part Number OL-10100-04 Copyright 2007-2008 Cisco Systems, Inc. All rights reserved N T E N T S Safety Precautions for Module Installation and Removal Cleaning the Fiber-Optic Connectors B-15 OL-10100-04 Contents Document History Document Organization Document ConventionsChapter Title Description Convention Description Related Documentation OL-10100-04 Cisco 7600 Product Overview Cisco 7600 Series Routers Supported Hardware Features Feature Description Feature Description Port Addresses Physical Interface Addresses MAC Addresses FAN Status Route Switch Processors Supervisor Engines Overview Product Number Description Product Number RSP720-3CXL-GE WS-SUP720-3BXL WS-SUP32-GE-3B Route Switch Processor WS-X6K-S2-MSFC2WS-X6K-S2U-MSFC2 WS-X6K-S2-PFC2 Supported Chassis, Line Cards, and Modules RSP720 FeaturesUnsupported Hardware and Features RSP720-10GE Features RSP720 with 10GE Uplink Ports Unsupported Features Unsupported Chassis and Modules RSP720-10GE Usage Guidelines and Limitations QoS on the RSP720-10GE QoS Configuration Guidelines Supervisor Engine 720 and Supervisor Engine Front-Panel Controls RSP720, RSP720-10GE, Sup720, Sup32 Color Description Front-Panel LEDs RSP720, RSP720-10GE, Sup720, Sup32Component Description Supervisor Engine Supervisor Engine 2 Front Panel Section on page 3-10 for more information Off when you insert a card Preparing for Installation or Removal Safety Precautions for Module Installation and Removal Preventing Electrostatic Discharge Damage Module Slot Assignments Tools Required for Module InstallationDetermining Module Location Installing a Supervisor Engine or Route Switch Processor Module Ejector Levers and Captive Installation Screws See Figure Removing a Supervisor Engine or Route Switch Processor Hot Swapping OIR Modules Removing and Replacing Memory Connecting to the Console Port Connecting a Terminal Supervisor Engine Connecting to the Uplink PortsConnecting a Modem Module Uplink Ports Using Flash Memory Cards Locating the Flash PC Card Write-Protection Switch Installing a Flash Memory Card Removing a Flash Memory Card Power Management and Environmental MonitoringDetermining Software Feature Support Regulatory Standards Compliance Module SpecificationsSpecification OL-10100-04 Cable and Connector Specifications Limiting Connection Distances Uplink Port Transceiver Modules Transceiver Module Part Numbers 1GE Uplink Ports and Cabling Specifications Product ID Description MMF SMF 10GE Uplink Ports and Cabling Specifications SMF ITU-T Console Port Cabling Specifications and Pinouts Gbic Module Cabling SpecificationsConsole Port Cabling Specifications MHz km Micron Console Port Signals and Pinouts Rate bps Distance feet Distance meters Signal RJ-45 Pin DB-9 Pin RJ-45-to-RJ-45 RJ-45-to-DB-9 ConsoleRollover Cable Device Rollover Cable Modem Adapter Signal RJ-45 Pin DB-25 Pin RJ-45-to-DB-25 Terminal ConsoleRJ-45-to-RJ-45 RJ-45-to-DB-25 RTS DTR Console Port Console Device RJ-45 ConnectorConsole Port Mode 2 Signaling and Pinouts Sup2 Only Side 2 Pin Signal RD+ TD+ Not used Side 1 Pin Signal Side 2 Pin Signal Fiber-Optic ConnectorsSC Connectors MT-RJ Connectors Figure B-5 SC Optical Connector LC Connectors Figure B-7 LC Fiber-Optic Connector Cleaning the Fiber-Optic Connectors LX/LH Gbic and MMF Cable Considerations Patch Cord Patch Cord Installation OL-10100-04 Active LED MAC GBICs, connecting to Gigabit Ethernet cables Active Console Link LED LX/LH GbicPWR Mgmt LED Nvram Status LED System LED