Chapter 13 Managing Reports

Working with Catalog Reports

Table 13-5

<report_name> Page (continued)

 

 

 

 

 

 

Option

 

Description

 

 

 

 

 

Failure Reason

 

Enter a failure reason name or click Select to enter a valid failure reason name on which to run your

 

 

 

 

 

 

 

report.

 

 

 

 

 

Protocol

 

Use the drop down list box to select which protocol on which you want to run your report. Valid options

 

 

 

 

 

 

 

are:

 

 

 

 

 

 

 

 

 

RADIUS

 

 

 

 

 

 

 

TACACS+

 

 

 

 

 

Authentication

 

Use the drop down list box to select which authentication status on which you want to run your report.

 

Status

 

Valid options are:

 

 

 

 

 

 

 

Pass Or Fail

 

 

 

 

 

 

 

Pass

 

 

 

 

 

 

 

Fail

 

 

 

 

 

Radius Audit

 

Enter the RADIUS audit session identification name on which you want to run a report.

 

Session ID

 

 

 

 

 

 

 

 

 

ACS Session ID

 

Enter the ACS session identification name on which you want to run a report.

 

 

 

 

 

Severity

 

Use the drop down list box to select the severity level on which you want to run a report. This setting

 

 

 

 

 

 

 

captures the indicated severity level and those that are higher within the threshold. Valid options are:

 

 

 

 

 

 

 

Fatal

 

 

 

 

 

 

 

Error

 

 

 

 

 

 

 

Warning

 

 

 

 

 

 

 

Info

 

 

 

 

 

 

 

Debug

 

 

 

 

 

End Point IP

 

Enter the end point IP address on which you want to run a report.

 

Address

 

 

 

 

 

 

 

 

 

Command

 

Check the check box to enable your report to run for command accounting.

 

Accounting Only

 

 

 

 

 

 

 

 

Top

 

Use the drop down list box to select the number of top (most frequent) authentications by access

 

 

 

 

 

 

 

service on which you want to run your report. Valid options are:

 

 

 

 

 

 

 

10

 

 

 

 

 

 

 

 

50

 

 

 

 

 

 

 

 

100

 

 

 

 

 

 

 

 

500

 

 

 

 

 

 

 

 

1000

 

 

 

 

 

 

 

 

All

 

 

 

 

 

By

 

Use the drop down list box to select the type of authentications on which you want to run your report.

 

 

 

 

 

 

 

Valid options are:

 

 

 

 

 

 

 

Passed Authentications

 

 

 

 

 

 

 

Failed Authentications

 

 

 

 

 

 

 

Total Authentications

 

 

 

 

 

 

 

 

 

 

 

 

 

User Guide for Cisco Secure Access Control System 5.3

 

 

 

 

 

 

 

 

 

 

 

13-16

 

 

 

 

 

 

OL-24201-01

 

 

 

 

 

 

 

 

 

Page 380
Image 380
Cisco Systems OL-24201-01 manual Radius, 13-16