Creating a vHBA, Click Add vHBA | Cisco Systems UCSCPCIECSC02

Managing Network Adapters

Creating a vHBA

Step 16 Click Save Changes.

Creating a vHBA

The adapter provides two permanent vHBAs. If NIV mode is enabled, you can create up to 16 additional vHBAs.

Procedure

Step 1 In the Navigation pane, click the Server tab.

Step 2 On the Server tab, click Inventory.

Step 3 In the Inventory pane, click the Network Adapters tab.

Step 4 In the Adapter Cards area, select the adapter card.

If the server is powered on, the resources of the selected adapter card appear in the tabbed menu below the Adapter Cards area.

Step 5 In the tabbed menu below the Adapter Cards area, click the vHBAs tab.

Step 6 In the Host Fibre Channel Interfaces area, choose one of these actions:

•To create a vHBA using default configuration settings, click Add.

•To create a vHBA using the same configuration settings as an existing vHBA, select that vHBA and click Clone.

The Add vHBA dialog box appears.

Step 7 In the Add vHBA dialog box, enter a name for the vHBA in the Name entry box.

Step 8 Click Add vHBA.

What to Do Next

•Reboot the server to create the vHBA.

•If configuration changes are required, configure the new vHBA as described in Modifying vHBA Properties, on page 11.

	Cisco UCS C-Series Servers Integrated Management Controller GUI Configuration Guide, Release 1.4
16	OL-23489-08

Image 16

Cisco Systems UCSCPCIECSC02 manual Creating a vHBA, Click Add vHBA

Contents

Managing Network Adapters Overview of the Cisco UCS C-Series Network Adapters Viewing Network Adapter Properties Cisco UCS P81E Virtual Interface Card Cimc Management Enabled PCI Slot columnProduct Name column Serial Number column Configuration Pending field FIP Mode fieldNIV Mode field Fault Configuring Adapter Properties Enable NIV Mode check box Number of VM FEX Interfaces Enable FIP Mode check boxClick Save Changes Managing vHBAs Guidelines for Managing vHBAsViewing vHBA Properties Name field FC SAN Boot check box Enable Persistent LUN BindingDefault Vlan field Class of Service drop-down list Enable FCP Error Recovery Link Down Timeout fieldPort Down Timeout field Ratov field Interrupt Mode drop-down list Flogi Timeout fieldThrottle Count field LUNs per Target field Modifying vHBA Properties World Wide Node Name field Error Recovery area, update the following fields Fibre Channel Interrupt area, update the following fields Name Creating a vHBA Click Add vHBA VHBA Boot Table Creating a Boot Table EntryDeleting a vHBA Fc1 Deleting a Boot Table Entry VHBA Persistent Binding Viewing Persistent Bindings Rebuilding Persistent Bindings Managing vNICsGuidelines for Managing vNICs Trust Host CoS check box Viewing vNIC PropertiesPCI Order field Enable Uplink Failover check box Enable PXE Boot check boxFailback Timeout field Interrupt Count field Coalescing Time fieldCoalescing Type drop-down list Receive Queue Count field Enable TCP Rx Offload Enable TCP Tx OffloadEnable Large Receive check box Transmit Queue Ring Size field Enable TCP-IPv6 Extension RSS Modifying vNIC Properties Access Ethernet Interrupt area, update the following fields Ethernet Transmit Queue area, update the following fields Enable TCP Receive Side Scaling Creating a vNIC Click Add vNIC Managing VM FEX Deleting a vNICVirtual Machine Fabric Extender Viewing Virtual FEX Properties Vlan Mode column PXE Boot fieldProperties button Uplink Failover column Interrupt Mode field Coalescing Type field Enable TCP Segmentation Enable Large Receive fieldEnable IPv4 RSS field Enable TCP-IPv4 RSS field Backing Up and Restoring the Adapter Configuration Exporting the Adapter ConfigurationClick Export Configuration Tftp Server IP Address field Restoring Adapter Defaults Importing the Adapter ConfigurationClick Import Configuration Managing Adapter Firmware Installing Adapter Firmware From a Local FileAdapter Firmware Installing Adapter Firmware From a Tftp Server Install Firmware button Resetting the Adapter Activating Adapter Firmware OL-23489-08