System Requirements | Cyclades 2.3.0, ACS48 guide

2: Installing the ACS

System Requirements

To configure the ACS, Cyclades recommends any of the following hardware specifications:

•Workstation with a console serial port or,

•Workstation with Ethernet and TCP/IP topology or,

•Cyclades AlterPath Manager.

The hardware connectivity required for each configuration method:

Hardware Connectivity	Configuration Method
Workstation, Hub Ethernet Cables.	Web browser, vi, Wizard, or CLI

Console, Console Cable (constructed from RJ45	vi, Wizard, or CLI.
straight-through cable + adapter
Workstation, Hub Ethernet Cables.

This manual is designed primarily for web browser users. If you will use vi, the wizard (CLI version) or CLI, refer to the ACS Reference Guide.

To install ACS with AlterPath Manager, refer to the AlterPath

Manager Manual and configure the device using the Manager.

Default Configuration Parameters

•DHCP enabled (if there is no DHCP Server, IP for Ethernet is 192.168.160.10 with a Netmask of 255.255.255.0)

•CAS configuration

•Socket_server in all ports (access method is telnet)

•9600 bps, 8N1

•No Authentication

AlterPath Console Server User Guide

13

Image 19

Cyclades 2.3.0, ACS48 System Requirements, Hardware Connectivity Configuration Method, Default Configuration Parameters

Contents

AlterPath Console Server Page Table of Contents Configuring the Web Interface Supported Browsers and JRE 139 Page Before You Begin Examples Outlines the Safety Considerations forExample Network Access Method Password field Example Naming Conventions To select is the same as to click your mouse Document Symbols Audience ACS Access and Configuration Product Models and Components Figure below shows AlterPath ACS1 through ACS48 ACS Setup Diagram Package Contents Installing the ACS Package Contents ACS4 through ACS48 Package Contents ACS1 Brackets Rack Mounting the ACS Default Configuration Parameters Hardware Connectivity Configuration MethodSystem Requirements Procedures given in Appendix C Supported Pre-Install ChecklistBrowsers and JRE Task 1 Install ACS and connect to the network Installation and Configuration Process Initial Configuration Using the ACS Console Port Task 2 Configure network settings Proceed to Task To create new users, see Wizard Mode Access page 4-10 Task 3 Configure via Web WizardTask 4 Test Configuration Task 5 Configure the web interface in Expert Mode Using the Web Interface Using the Web Interface System brings up the Port Selection form Using the Command Line Interface CLI Where Telnet AccessSSH Access Logging onto the Terminal Tsmenu Access From Telnet Closing the session from tsmenuFrom SSH Power Management Security Overview Configuring the Web Interface For more detailed information, see Chapter Logging Configuring the Web Interface Menu Panel Control Buttons Wizard ModeACS Web Interface GUI Elements User Entry Panel or Form Form Tabs Expert ModeOr Form Indicator Top Menu Bar Button Functions Saving Your ConfigurationButton Name Use this button to Configuring the Web Interface Network Settings Configuring in Wizard ModeSettings Configuring the Web Interface Port Profile Field Name Definition Then go to Security Users and Groups Access Changing a User Password User Name PasswordRepeat Password Adding a User Select Apply Changes Deleting a User Data Buffering Record the time stamp DestinationMode File Size Bytes System Log Menu Selection Use this menu to Configuring in Expert ModeExpert Mode Menu Applications Security Network Ports Administration Applications Connect Form Title Use this form to Applications Power Management Applications Power management Outlets Manager To Edit the Power Up Interval Applications Power Management View IPDUs Info Applications Power Management Users Manager Deleting a User Applications Power Management Configuration Applications Power Management Software Upgrade Configuring the Web Interface Applications Terminal Profile Menu Configuring the Web Interface Network Host Settings Filed Name Field Definition Syslog Servers Network SyslogFacility Number New Syslog Server Network Pcmcia Management Isdn GSM Pcmcia Configuration Dialog Boxes Call Back Access Method ModemLocal IP Remote IP Access Method Isdn Pin Number Access Method GSM Access Method Compact Flash Access Method Ethernet Access Method Wireless LAN Role of IPsec What is VPN Authentication Keys Network VPN Connections Remote Right Authentication ProtocolAuthentication Method Connection Name Local Left Snmp Daemon SettingsBoot Action RSA Key Community To configure Snmp Source If you are using SNMPv3, skip steps 2 and 3 proceed to stepSysContact SysLocation Permission System invokes the New/Modify Snmp v3 Configuration dialog Services Rule Firewall ConfigurationStructure of IP Filtering Chain Network Firewall Configuration Editing a Chain Adding a Chain Editing a Rule Deleting a Chain Inverted TargetSource IP Mask Destination IP Adding a Rule Additional Fields About the Reject Options Section Network Host Table Network Static Routes Metric Route Select Default , Network , or Host Network IPHost IP Go to Select Gateway or Interface Users and Groups Adding Users and Groups to the Access List All users must be assigned to a group Changing the User PasswordDeleting a User from a Group From LoginActive Ports Sessions User Virtual Ports PortsPorts Physical Ports Physical Ports To configure the ports Associating an Alias to a Port Alias Ports Physical Ports General PortBaud Rate Kbps Go to Ports Physical Ports General Power Management Access Authentication Type Definition Ports Physical Ports Access NIS NIS Field Name Entry Fields Based on Authentication TypeAuthentication Radius Authentication Ldap or LdapDownLocal Authorized Users/Groups NIS Domain Name NIS Server IP Authentication Type NIS, LocalNIS or NISLocal All ACS onlyAuthentication Type Kerberos, KerberosDownLocal KerberosDownLocal Syslog Server Ports Physical Ports Data BufferingFull Size Bytes Record the timestamp Ports Physical Ports Multi-User Menu Hotkey To configure ACS to allow multiple sessionsSniff Mode Allow Multiple Sessions Ports Physical Ports Power Management Ports Physical Ports Other TCP Keep-alive Interval Ports Virtual Ports First Remote TCP Port No Number of PortsFirst Local Port No First Local TCP Port No Deleting a Slave Ports Ports Status Configuring the Web Interface 112 Administration System Information Administration Notification Alarm for Administration NotificationEmail , Pager , or Snmp Trap Smtp Port Alarm TriggerTo/From/Subject/Body Smtp Server IP SMS Port Pager NumberText SMS Server IP 117 Server IP Port DCD Alarm NotificationOID Type Value Trap Number Manual Setting Administration Time / Date NTP Setting Field Name Definition Administration Boot Configuration Server’s IP Address Unit boot fromBoot Type Boot File Name To save configuration to a FTP server Administration Backup Configuration Backup and Restore Procedure Click on Apply Changes To Save Configuration to a Storage DeviceDefault Configuration Replace Configuration Click on Upgrade Now Administration Upgrade Firmware Administration Reboot Configuring the Web Interface 128 Hardware Specifications Supported Pcmcia Cards MK5002MPL 5GB Appendix a Hardware Specifications 132 Safety Guidelines for Rack-Mounting the ACS Reliable Earthing Safety Precautions for Operating the ACS Working inside the AlterPath Console Port Server Canadian DOC Notice Replacing the BatteryWarnung FCC Warning Statement Aviso de Precaución S-Mark Argentina Batería Trabajar dentro del AlterPath Console Server Requirements From Windows Internet Explorer Installing JRESupported Web Browsers Tested Environment From Windows Netscape or Mozilla Break Signal AuthenticationBios Boot Dhcp CAS Commands Domain Name Server. The computer you use to accessSequence of special characters that sends a command to a An escape sequence is commonly used when the computer Icmp Kerberos IP packet filteringIPsec Isdn Network Mask MACMasquerading MTU NTP NFSObject Identifiers OID Parity OIDSee Object Identifier Packet Port PcmciaPPP Risc Radius Snmp Smtp TACACS+ Terminal Access Controller Access Control SystemStty Tacacs UDP TelnetTerminal Server TTY Watchdog timer can be programmed to perform a warm Watchdog timer WDT is a device or electronic card thatSystem does not recover on its own Common problem is for a machine or operating system to