TRANSCEIVER OPERATION
2-14
November 1999
Part No. 001-7780-500
2. Enter the index of the desired ID if you know it or
scroll through the list using the and keys
until you find the desired ID. Press th e CLRkey to
cancel the call.
3. Press the PTT switchor the ENTkey to initiate the
call. The displaythen indicates the alias of the desti-
nation radio. Proceed to the bulleted list following
the next method for conditions thatmay occur next.
Direct Entry Method (Full Keypad Mo dels Only)
1. With a SMARTNET/SmartZonechannel selected,
press and hold the Private Call option switch u ntil a
tone sounds (approximately 1 second). The last ID
called is displayed,and the private call mode is indi-
cated by “C” in the upper part of the display.
2. Using the 0-9 keys, enter the 6-digit ID of the
mobile unit you are calling. Press the key to
erase the last digit enteredor press the CLR key to
cancel the call.
3. Press the PTT switchor the ENT key to initiate the
call. If the entered ID is invali d, “INVALID” is
momentarily displayed and the call is not initiated.
If the entered ID is valid, the d isplay indicates the
alias of the ID if it matches an ID in your call list.
Otherwise, the ID you entered continue st o be
displayed. Any of the followingconditions may
then occur:
•If the radio you are callingis on the air, telephone
type “ringing” is heard for20 seconds or until the
called party answers.
•If the called party answersand the call is
successful,the person’s voice is heardand the call
is carried on the same as a group call.To end the
call at any time, press the CLR key.
•If the called party does not answer within 20
seconds, “NO ANSWR” is displayed and a
continuous tone sounds. End the call by pressing
the CLR key.
•If the called radio is not in service, no ringing is
heard, “NO ACK” is displayed, and a continuous
tone sounds. End the call by pressingthe CLR
key.
•If neither your radio nor the radio bei ngc alled is
authorized to make unit-to-unit c alls, “REJECT”
is displayed and a continuous tone sounds. End
the call by pressing the CLR key.
•If the called partyanswers but the radio system is
busy, fourlow tones sound and “BUSY” and
“WAIT”are alternately displayed. When the
system is no longer busy,the called party auto-
matically responds.
•If an out-of-range conditionexists or the radio
system is not in service, “LOST CALL” is
displayed and a continuous tone sounds. End the
call by pressing the CLR key.
Receiving an Enhanced Privat e Conversation Call
These calls are automatically receivedif a
SMARTNET/SmartZone channelis selected. Proceed
as follows:
1. When a call is received, a recurr ing unit call tone
(three beeps) sounds for up to 20 seconds, and
“CALL RCV” and the current channel alias are
alternately displayed.
2. To answer the call,press the Private Call option
switch and then the PTT switch and begin talk ing.
The private call mode is indicated by “C”inthe
upper part of the display.The alias of the incoming
call is displayed if the ID is in your call list. Other-
wise, the unit ID is displayed. NOTE: If the Private
Call option switch is not pressed beforethe PTT
switch, a group call is transmitted on the selected
group.
•Toend the call when the conversation is complete
or at any other time, press the CLR key.
•If unit-to-unit (private)calls are not permitted
(Private Call switch not programmed), press the
Call Response option switch, if available,to
answer the call.
•If the call is not answered within 20 second s, it is
automatically terminated.
•If the radio system is busy,four low tones sound
and “BUSY” and “WAIT”are alternately