TRANSCEIVER OPERATION
2-15 November 1999
Part No. 001-7780-500
displayed.When the system is no longer busy, the
callback tone (four beeps) is heard and your radio
automatically startstransmitting. Press the PTT
switchtocontinuethecall.
•Toign ore an incoming call, press the CLR key or
wait 20 seconds until the recurring unit call tone
stops sounding. NOTE:IftheCLRkeyis
programmedfor the Call function, it will not clear
the call.
2.5.5 PRIVATE CONVERSATION II CALLS
General
Private calls allow you to place a c all to a specific
mobile unit. Either the Enhanced Private Conve rsa-
tion™ or Private Conversation II™ modes may be
programmed depending on the capabilitiesof the radio
system. Operation in the EnhancedPrivate Conversa-
tion mode was described in Section2.5.4, and opera-
tion in the Private ConversationII mode is described
in the following information.
The Private Call option switch is required to
place these calls, and either that switch or the Call
Response option switch is required to receivethem.
Proceed as follows.
Placing a Private Conversation II Call
This call can be initiatedby selecting the unit ID
from a call list (list entry) or by directly entering it
using the keypad (direct entry).Direct entry is avail-
able with full keypad (15-key) models only.Proceed
as follows:
List Entry Method (All Models)
1. With a SMARTNET/SmartZonechannel selected,
momentarily press the PrivateCall option switch.
The private call mode is indicated by “C”inthe
upper part of the display.The tag (alias) of the last
ID called isdisplayed if it matches an ID in your call
list. Otherwise, the last ID called is displayed.
2. Enter the index of the desired ID if you know it or
scroll through the list using the and keys
until you find the desired ID. Press theCLR key to
cancel the call.
3. Press the PTTswitch to initiate the call. The display
then indicatesthe alias of the destination radio. Wait
approximately 1 second and then begin talking.
Proceed to the bulleted listwhich follows the next
method for conditions that may then occur.
Direct Entry Method (Full Ke ypad Models Only)
1. With a SMARTNET/SmartZonechannel selected,
press and hold the PrivateCall option switch until a
tone sounds (approximately 1 second). The last ID
called is displayed and the privatecall mode is indi-
cated by “C” in the upper part of the display.
2. Using the 0-9 keys, enter the 6-digit ID of the unit
you are calling. Press the key to erase the last
digit entered or pressthe CLR key to cancel the call.
3. Press the PTT switch to initiatethe call. If the
entered ID is invalid, “INVALID” is momentarily
displayed and the call is not initiated. If the en tered
ID is valid, the display indicates the aliasof the ID
if it matches an ID in your call list. Otherwise, the
ID you entered continues to be displayed.Wait
approximately1 second and then begin talking. Any
of the following conditions may thenoccur.
•If the called party answers and the call is
successful,the person’s voice is heard and the call
iscarriedonthesameasagroupcall.Toendthe
call at any time, press the CLR key.
•If the radio system is busy,four low tones sound
and the “BUSY” and “WAIT”are alternately
displayed.When the system is no longer busy, the
call back tone (four beeps)is heard and a channel
is automatically acquired. Press the PTT switch to
continue the call.
Receiving a Private ConversationII Call
Unit-to-unit calls are automatically rec eived if a
SMARTNET/SmartZone channelis selected. Proceed
as follows:
1. When a call is received,an alert tone sounds and the
caller’s voice isheard. While voice is heard, “C”is
indicatedin the upper part of the display and “CALL
RCV” and the current channel aliasare alternately
displayed.