Wiring Diagram for Free Chlorine Sensor | Emerson 1056 instruction

MODEL FCL-1056

Figure 3-3. Wiring Diagram for Free Chlorine Sensor

Figure 3-5. Wiring Diagram

for 3900VP-10 pH sensor (gray cable)

SECTION 3.0

WIRING

WHITE

RED

Figure 3-4. Wiring Diagram

for 399VP-09 pH Sensor

Figure 3-6. Wiring Diagram

for 3900VP-10 pH sensor (blue cable)

11

Image 21

Emerson PN 51-FCL-1056 instruction manual Wiring Diagram for Free Chlorine Sensor

Contents

FCL with 1056 Analyzer Essential Instructions Free Chlorine EnglishPpm mg/L ORP S1 Free Cl PH Correction Manual Live/ContinousS1 Manual pH Temp Units Menu Tree Calibrate Sensor 1 Free chlorineSensor 2 pH Temperature AlarmsDiagnostic Setup Reset Analyzer Rev. Level Date About This Document FCL-1056 Table of Contents List of Tables Table of Contents CONT’D Iii List of Tables CONT’D Section Description and Specifications FeaturesApplications Specifications General Specifications SensorSpecifications Analyzer Ordering Information AccessoriesComponent Parts PH Correction required selection This page left blank intentionally Unpacking and Inspection Section InstallationFCL-01 free chlorine without continuous pH correction FCL-02 free chlorine with continuous pH correction Installing the Sensors InstallationGeneral Information Mounting, Inlet, and Drain Connections Model FCL-01 This page left blank intentionally POWER, ALARM, and Output Wiring Section WiringPower Analog output wiring Alarm relay connections Sensor Wiring Wiring Diagram for Free Chlorine Sensor Model FCL-1056 Section Wiring Display Section Display and Operation Keypad Calibrate Programming the ANALYZER-TUTORIALOutputs Range O1 S1 20mA 08.50 ppm Output Range O1 S1 4mA 0.000 ppmO2 S1 4mA 0.0C O2 S1 20mA 100.0C Security Hold Using Hold Main Format Configuring the Main DisplayLanguage English Contrast Format, Language, Warning, and Contrast Default Settings Section Programming the AnalyzerGeneral Sensor assignment Alarms Choices Default Definitions CONFIGURING, RANGING, and Simulating Outputs Configure ProgramOutputAssign Procedure Ranging Outputs Configure Simulate Output ConfigureOutput Output Range O1 S1 20mA 10.00 ppm O2 S1 4mA 0.0C O2 S1 20mA 100.0C Configuring Alarms and Assigning Setpoints Configure SimulateRangeSimulate Output Section Programming the Analyzer Alarms Configure/SetpointAlarm Alarm Simulate Alarm Alarms Configure/SetpointSimulate Don’t Simulate Alarms Configure/Setpoint Simulate Synch Timers YesProcedure Synchronizing Timers Configuring the Measurement Definitions ChlorineDefinitions pH/ORP Sensor1Sensor Measurement Definitions pH Configuring Temperature Related Settings Temperature Program Outputs Alarms MeasurementConfiguring Security Settings S1 Temp Comp Auto S2 Temp Comp Setting UP Diagnostics Program Alarms Measurement TemperatureSecurity Security Diagnostic Setup Program Measurement Temperature SecurityGI Fault High 1500MΩ Procedure Setting Up Diagnostics Program Temperature Security Diagnostics Resetting the AnalyzerReset Analyzer Reset Analyzer Calibrating Temperature Section CalibrationIntroduction Calibrate SensorSensor11 Output ProcedureS1 Calibration S1 Calibration + 25.0C Calibration Free Chlorine Procedure-Zeroing the Sensor Choose Free Chlorine Calibrate SensorSensor11 Output S1 Calibration Calibrate? Temperature S1 Calibration ZeroZeroCalCal Process CalSensor Sensor Output Calibration Slope and Offset Calibration pH Auto ZeroBufferCalCal 07.01 pH 10.01 pHStable Time Buffer Manual Manual Buffer 1 0 7.00 pH S2 pH Manual Cal Buffer StandardizeStandardize Redox Temperature S2 pH Cal Buffer CalSlope 56.19 mV/pH Offset S1 Enter Value 00 pH Procedure-Entering a Known Slope and Offset Calibration Analog Outputs OutputMA Output Cal Meter 000 mA Trim Complete This page left blank intentionally Section Digital Communications Model FCL-1056 Section Analyzer Section Maintenance Replacing the electrolyte solution and membrane Cleaning the membraneChlorine Sensor General Cleaning the Sensor Other MaintenancePH Sensor Constant Head Flow Controller Cleaning the flow controller Weight Weight Using the Diagnostic Feature Section TroubleshootingFaults Overview Troubleshooting When a Fault Message is Showing Fault message Explanation SectionHardware Error Sensor ADC Error Sensor CPU ErrorSensor Incompatible Sensor RTD Open Glass Z Too High Sensor RTD Out of RangeReference Impedance Too High Broken Glass Troubleshooting When a Warning Message is Showing Troubleshooting When no Error Message is Showing Chlorine Sensor can be calibrated, but the current is too low Process readings are erraticReadings drift Chlorine readings are too low Sensor does not respond to changes in chlorine level Calibration Error During Two-Point Calibration Troubleshooting When no Error Message is Showing pH Sensor Does Not Respond to Known pH Changes Calibration Error during Standardization PH Readings Are Moderately Noisy and Tend to Wander Simulating Inputs Chlorine Troubleshooting When no Error Message is Showing GeneralAnod Cath Simulating pH input Simulating Inputs pH Simulating temperature Simulating Inputs TemperaturePage ASIA-PACIFIC Americas HeadquartersEurope Germany Warranty Specifications subject to change without notice