Menu Tree, Calibrate Sensor 1 Free chlorine

MENU TREE

Calibrate

Sensor 1 (Free chlorine)

Chlorine

Zero

In process

Temperature

Sensor 2 (pH)

Buffer Cal

Auto

Select buffer (NIST, DIN19267, Ingold, Merck, or Fisher) Select stability criteria

Manual Standardize Enter slope or offset

Temperature

Output 1

Output 2

Hold

Sensor 1

Sensor 2

Display

Main format configuration

Language selection

Warning (enable or disable)

Screen contrast

See next page for rest of menu tree

Page 5

Image 5

Emerson PN 51-FCL-1056 instruction manual Menu Tree, Calibrate Sensor 1 Free chlorine, Sensor 2 pH

Contents

FCL with 1056 Analyzer Essential Instructions Free Chlorine EnglishPpm mg/L ORP S1 Manual pH Temp Units S1 Free Cl PH Correction ManualLive/Continous Sensor 2 pH Menu TreeCalibrate Sensor 1 Free chlorine Temperature AlarmsDiagnostic Setup Reset Analyzer Rev. Level Date About This Document FCL-1056 Table of Contents List of Tables Table of Contents CONT’D Iii List of Tables CONT’D Applications Section Description and SpecificationsFeatures Specifications Analyzer Specifications GeneralSpecifications Sensor Ordering Information AccessoriesComponent Parts PH Correction required selection This page left blank intentionally Unpacking and Inspection Section InstallationFCL-01 free chlorine without continuous pH correction FCL-02 free chlorine with continuous pH correction Installing the Sensors InstallationGeneral Information Mounting, Inlet, and Drain Connections Model FCL-01 This page left blank intentionally POWER, ALARM, and Output Wiring Section WiringPower Analog output wiring Alarm relay connections Sensor Wiring Wiring Diagram for Free Chlorine Sensor Model FCL-1056 Section Wiring Display Section Display and Operation Keypad Calibrate Programming the ANALYZER-TUTORIALOutputs Range O1 S1 20mA 08.50 ppm Output Range O1 S1 4mA 0.000 ppmO2 S1 4mA 0.0C O2 S1 20mA 100.0C Security Hold Using Hold Main Format Configuring the Main DisplayLanguage English Contrast Format, Language, Warning, and Contrast General Default SettingsSection Programming the Analyzer Sensor assignment Alarms Choices Default Definitions CONFIGURING, RANGING, and Simulating Outputs Assign ConfigureProgramOutput Procedure Ranging Outputs Configure Simulate Output ConfigureOutput Output Range O1 S1 20mA 10.00 ppm O2 S1 4mA 0.0C O2 S1 20mA 100.0C Configuring Alarms and Assigning Setpoints Configure SimulateRangeSimulate Output Section Programming the Analyzer Alarm AlarmsConfigure/Setpoint Alarm Simulate Alarm Alarms Configure/SetpointSimulate Don’t Simulate Procedure Synchronizing Timers Alarms Configure/Setpoint SimulateSynch Timers Yes Definitions pH/ORP Configuring the MeasurementDefinitions Chlorine Sensor1Sensor Measurement Definitions pH Configuring Temperature Related Settings Temperature Program Outputs Alarms MeasurementConfiguring Security Settings S1 Temp Comp Auto S2 Temp Comp Setting UP Diagnostics Program Alarms Measurement TemperatureSecurity Security Diagnostic Setup Program Measurement Temperature SecurityGI Fault High 1500MΩ Procedure Setting Up Diagnostics Program Temperature Security Diagnostics Resetting the AnalyzerReset Analyzer Reset Analyzer Introduction Calibrating TemperatureSection Calibration Calibrate SensorSensor11 Output ProcedureS1 Calibration S1 Calibration + 25.0C Calibration Free Chlorine Procedure-Zeroing the Sensor Choose Free Chlorine Calibrate SensorSensor11 Output S1 Calibration Calibrate? Temperature S1 Calibration ZeroZeroCalCal Process CalSensor Sensor Output Calibration Slope and Offset Calibration pH Auto ZeroBufferCalCal Stable Time 07.01 pH10.01 pH Buffer Manual Manual Buffer 1 0 7.00 pH S2 pH Manual Cal Buffer StandardizeStandardize Redox Temperature S2 pH Cal Buffer CalSlope 56.19 mV/pH Offset S1 Enter Value 00 pH Procedure-Entering a Known Slope and Offset MA Output Cal Meter 000 mA Trim Complete Calibration Analog OutputsOutput This page left blank intentionally Section Digital Communications Model FCL-1056 Section Analyzer Section Maintenance Replacing the electrolyte solution and membrane Cleaning the membraneChlorine Sensor General PH Sensor Cleaning the SensorOther Maintenance Constant Head Flow Controller Cleaning the flow controller Weight Weight Using the Diagnostic Feature Section TroubleshootingFaults Overview Hardware Error Troubleshooting When a Fault Message is ShowingFault message Explanation Section Sensor ADC Error Sensor CPU ErrorSensor Incompatible Sensor RTD Open Glass Z Too High Sensor RTD Out of RangeReference Impedance Too High Broken Glass Troubleshooting When a Warning Message is Showing Troubleshooting When no Error Message is Showing Chlorine Readings drift Sensor can be calibrated, but the current is too lowProcess readings are erratic Chlorine readings are too low Sensor does not respond to changes in chlorine level Calibration Error During Two-Point Calibration Troubleshooting When no Error Message is Showing pH Sensor Does Not Respond to Known pH Changes Calibration Error during Standardization PH Readings Are Moderately Noisy and Tend to Wander Simulating Inputs Chlorine Troubleshooting When no Error Message is Showing GeneralAnod Cath Simulating pH input Simulating Inputs pH Simulating temperature Simulating Inputs TemperaturePage ASIA-PACIFIC Americas HeadquartersEurope Germany Warranty Specifications subject to change without notice

Emerson PN 51-FCL-1056 Menu Tree, Calibrate Sensor 1 Free chlorine, Sensor 2 pH

Models: 1056 PN 51-FCL-1056

MENU TREE

Calibrate

Sensor 1 (Free chlorine)

Sensor 2 (pH)