Alarms Configure/Setpoint Simulate, Synch Timers Yes | Emerson 1056

MODEL FCL-1056	SECTION 5.0
	PROGRAMMING THE ANALYZER

5.4.4 Procedure – Synchronizing Timers

1. Synch Timers is available only if two or more alarm relays have been configured as interval timers.

Program

Outputs

Alarms

Measurement

Temperature

2.Press MENU. The main menu screen appears. Move the cursor to Program and press ENTER.

3.Choose Alarms.

Alarms

Configure/Setpoint

Simulate

Synch Timers: Yes

4.The summary display shows the current Synch Timers setting (Yes or No).

To make a change, choose Synch Timers and press ENTER. A screen will appear in which the present setting can be edited. Press ENTER to store the setting.

For an explanation of terms, see sections 5.4.1 and 5.4.2.

5. To return to the main display, press MENU then EXIT.

29

Image 39

Emerson PN 51-FCL-1056 Alarms Configure/Setpoint Simulate, Synch Timers Yes, Procedure Synchronizing Timers

Contents

FCL with 1056 Analyzer Essential Instructions ORP EnglishFree Chlorine Ppm mg/L S1 Free Cl PH Correction Manual Live/ContinousS1 Manual pH Temp Units Menu Tree Calibrate Sensor 1 Free chlorineSensor 2 pH Reset Analyzer AlarmsTemperature Diagnostic Setup Rev. Level Date About This Document FCL-1056 Table of Contents List of Tables Table of Contents CONT’D Iii List of Tables CONT’D Section Description and Specifications FeaturesApplications Specifications General Specifications SensorSpecifications Analyzer PH Correction required selection AccessoriesOrdering Information Component Parts This page left blank intentionally FCL-02 free chlorine with continuous pH correction Section InstallationUnpacking and Inspection FCL-01 free chlorine without continuous pH correction Mounting, Inlet, and Drain Connections InstallationInstalling the Sensors General Information Model FCL-01 This page left blank intentionally Analog output wiring Section WiringPOWER, ALARM, and Output Wiring Power Alarm relay connections Sensor Wiring Wiring Diagram for Free Chlorine Sensor Model FCL-1056 Section Wiring Display Section Display and Operation Keypad Range Programming the ANALYZER-TUTORIALCalibrate Outputs Security Output Range O1 S1 4mA 0.000 ppmO1 S1 20mA 08.50 ppm O2 S1 4mA 0.0C O2 S1 20mA 100.0C Hold Using Hold Format, Language, Warning, and Contrast Configuring the Main DisplayMain Format Language English Contrast Default Settings Section Programming the AnalyzerGeneral Sensor assignment Alarms Choices Default Definitions CONFIGURING, RANGING, and Simulating Outputs Configure ProgramOutputAssign O1 S1 20mA 10.00 ppm O2 S1 4mA 0.0C O2 S1 20mA 100.0C Configure Simulate Output ConfigureProcedure Ranging Outputs Output Output Range Output Configure SimulateConfiguring Alarms and Assigning Setpoints RangeSimulate Section Programming the Analyzer Alarms Configure/SetpointAlarm Don’t Simulate Alarms Configure/SetpointAlarm Simulate Alarm Simulate Alarms Configure/Setpoint Simulate Synch Timers YesProcedure Synchronizing Timers Configuring the Measurement Definitions ChlorineDefinitions pH/ORP Sensor1Sensor Measurement Definitions pH Configuring Temperature Related Settings S1 Temp Comp Auto S2 Temp Comp Program Outputs Alarms MeasurementTemperature Configuring Security Settings Security Program Alarms Measurement TemperatureSetting UP Diagnostics Security Procedure Setting Up Diagnostics Program Measurement Temperature SecurityDiagnostic Setup GI Fault High 1500MΩ Reset Analyzer Resetting the AnalyzerProgram Temperature Security Diagnostics Reset Analyzer Calibrating Temperature Section CalibrationIntroduction S1 Calibration + 25.0C ProcedureCalibrate SensorSensor11 Output S1 Calibration Calibration Free Chlorine Procedure-Zeroing the Sensor Choose Free Chlorine Calibrate SensorSensor11 Output S1 Calibration Sensor Output Temperature S1 Calibration ZeroZeroCalCal Process CalCalibrate? Sensor Calibration Slope and Offset Calibration pH Auto ZeroBufferCalCal 07.01 pH 10.01 pHStable Time Buffer Manual Manual Buffer 1 0 7.00 pH S2 pH Manual Cal Buffer S1 Enter Value 00 pH Redox Temperature S2 pH Cal Buffer CalStandardizeStandardize Slope 56.19 mV/pH Offset Procedure-Entering a Known Slope and Offset Calibration Analog Outputs OutputMA Output Cal Meter 000 mA Trim Complete This page left blank intentionally Section Digital Communications Model FCL-1056 Section Analyzer Section Maintenance General Cleaning the membraneReplacing the electrolyte solution and membrane Chlorine Sensor Cleaning the Sensor Other MaintenancePH Sensor Constant Head Flow Controller Cleaning the flow controller Weight Weight Overview Section TroubleshootingUsing the Diagnostic Feature Faults Troubleshooting When a Fault Message is Showing Fault message Explanation SectionHardware Error Sensor RTD Open Sensor CPU ErrorSensor ADC Error Sensor Incompatible Broken Glass Sensor RTD Out of RangeGlass Z Too High Reference Impedance Too High Troubleshooting When a Warning Message is Showing Troubleshooting When no Error Message is Showing Chlorine Sensor can be calibrated, but the current is too low Process readings are erraticReadings drift Chlorine readings are too low Sensor does not respond to changes in chlorine level Calibration Error During Two-Point Calibration Troubleshooting When no Error Message is Showing pH Sensor Does Not Respond to Known pH Changes Calibration Error during Standardization PH Readings Are Moderately Noisy and Tend to Wander Cath Troubleshooting When no Error Message is Showing GeneralSimulating Inputs Chlorine Anod Simulating pH input Simulating Inputs pH Simulating temperature Simulating Inputs TemperaturePage Germany Americas HeadquartersASIA-PACIFIC Europe Warranty Specifications subject to change without notice