Alarms Configure/Setpoint, Simulate | Emerson PN 51-FCL-1056

MODEL FCL-1056	SECTION 5.0
	PROGRAMMING THE ANALYZER

5.4.4Procedure – Simulating Alarms

1.Press MENU. The main menu screen appears. Move the cursor to Program and press ENTER.

Program

Outputs

Alarms

Measurement

Temperature

2.Choose Alarms.

Alarms

Configure/Setpoint

Simulate

Synch Timers: Yes

3.Choose Simulate.

Simulate

Alarm 1

Alarm 2

Alarm 3

Alarm 4

Simulate Alarm 1

Don’t Simulate

De-energize

Energize

4.Choose Alarm 1, Alarm 2, Alarm 3, or Alarm 4.

5.Choose Don’t simulate, De-energize, or Energize. Press MENU or EXIT to end simulation.

28

Image 38

Emerson PN 51-FCL-1056 Alarms Configure/Setpoint, Alarm Simulate Alarm, Don’t Simulate, De-energize Energize

Contents

FCL with 1056 Analyzer Essential Instructions Ppm mg/L EnglishFree Chlorine ORP S1 Manual pH Temp Units S1 Free Cl PH Correction ManualLive/Continous Sensor 2 pH Menu TreeCalibrate Sensor 1 Free chlorine Diagnostic Setup AlarmsTemperature Reset Analyzer About This Document Rev. Level Date Table of Contents FCL-1056 Table of Contents CONT’D List of Tables List of Tables CONT’D Iii Applications Section Description and SpecificationsFeatures Specifications Analyzer Specifications GeneralSpecifications Sensor Component Parts AccessoriesOrdering Information PH Correction required selection This page left blank intentionally FCL-01 free chlorine without continuous pH correction Section InstallationUnpacking and Inspection FCL-02 free chlorine with continuous pH correction General Information InstallationInstalling the Sensors Mounting, Inlet, and Drain Connections Model FCL-01 This page left blank intentionally Power Section WiringPOWER, ALARM, and Output Wiring Analog output wiring Sensor Wiring Alarm relay connections Wiring Diagram for Free Chlorine Sensor Model FCL-1056 Section Wiring Section Display and Operation Display Keypad Outputs Programming the ANALYZER-TUTORIALCalibrate Range O2 S1 4mA 0.0C O2 S1 20mA 100.0C Output Range O1 S1 4mA 0.000 ppmO1 S1 20mA 08.50 ppm Security Using Hold Hold Language English Contrast Configuring the Main DisplayMain Format Format, Language, Warning, and Contrast General Default SettingsSection Programming the Analyzer Alarms Sensor assignment Choices Default CONFIGURING, RANGING, and Simulating Outputs Definitions Assign ConfigureProgramOutput Output Output Range Configure Simulate Output ConfigureProcedure Ranging Outputs O1 S1 20mA 10.00 ppm O2 S1 4mA 0.0C O2 S1 20mA 100.0C RangeSimulate Configure SimulateConfiguring Alarms and Assigning Setpoints Output Section Programming the Analyzer Alarm AlarmsConfigure/Setpoint Simulate Alarms Configure/SetpointAlarm Simulate Alarm Don’t Simulate Procedure Synchronizing Timers Alarms Configure/Setpoint SimulateSynch Timers Yes Definitions pH/ORP Configuring the MeasurementDefinitions Chlorine Measurement Sensor1Sensor Configuring Temperature Related Settings Definitions pH Configuring Security Settings Program Outputs Alarms MeasurementTemperature S1 Temp Comp Auto S2 Temp Comp Security Program Alarms Measurement TemperatureSetting UP Diagnostics Security GI Fault High 1500MΩ Program Measurement Temperature SecurityDiagnostic Setup Procedure Setting Up Diagnostics Reset Analyzer Resetting the AnalyzerProgram Temperature Security Diagnostics Reset Analyzer Introduction Calibrating TemperatureSection Calibration S1 Calibration ProcedureCalibrate SensorSensor11 Output S1 Calibration + 25.0C Procedure-Zeroing the Sensor Calibration Free Chlorine Calibrate SensorSensor11 Output S1 Calibration Choose Free Chlorine Sensor Temperature S1 Calibration ZeroZeroCalCal Process CalCalibrate? Sensor Output Calibration pH Calibration Slope and Offset ZeroBufferCalCal Auto Stable Time 07.01 pH10.01 pH Manual Buffer Manual Buffer 1 0 7.00 pH S2 pH Manual Cal Buffer Slope 56.19 mV/pH Offset Redox Temperature S2 pH Cal Buffer CalStandardizeStandardize S1 Enter Value 00 pH Procedure-Entering a Known Slope and Offset MA Output Cal Meter 000 mA Trim Complete Calibration Analog OutputsOutput This page left blank intentionally Section Digital Communications Model FCL-1056 Section Section Maintenance Analyzer Chlorine Sensor Cleaning the membraneReplacing the electrolyte solution and membrane General PH Sensor Cleaning the SensorOther Maintenance Cleaning the flow controller Constant Head Flow Controller Weight Weight Faults Section TroubleshootingUsing the Diagnostic Feature Overview Hardware Error Troubleshooting When a Fault Message is ShowingFault message Explanation Section Sensor Incompatible Sensor CPU ErrorSensor ADC Error Sensor RTD Open Reference Impedance Too High Sensor RTD Out of RangeGlass Z Too High Broken Glass Troubleshooting When a Warning Message is Showing Troubleshooting When no Error Message is Showing Chlorine Readings drift Sensor can be calibrated, but the current is too lowProcess readings are erratic Sensor does not respond to changes in chlorine level Chlorine readings are too low Troubleshooting When no Error Message is Showing pH Calibration Error During Two-Point Calibration Calibration Error during Standardization Sensor Does Not Respond to Known pH Changes PH Readings Are Moderately Noisy and Tend to Wander Anod Troubleshooting When no Error Message is Showing GeneralSimulating Inputs Chlorine Cath Simulating Inputs pH Simulating pH input Simulating Inputs Temperature Simulating temperaturePage Europe Americas HeadquartersASIA-PACIFIC Germany Warranty Specifications subject to change without notice