RangeSimulate, Configure Simulate, Output, 00 mA | Emerson 1056

MODEL FCL-1056	SECTION 5.0
	PROGRAMMING THE ANALYZER

5.3.5 Procedure – Simulating Outputs

Program

Outputs

Alarms

Measurement

Temperature

1.Press MENU. The main menu screen appears. Move the cursor to Program and press ENTER.

2.The cursor will be on Outputs. Press ENTER.

Outputs

RangeSimulate

Configure

Simulate

Simulate

ProgramOutput 1

Output 2

3.Choose Simulate.

4.Choose Output 1 or Output 2.

Output 1 Hold at

1 2.00 mA

5.Enter the desired simulated output current. To end the simulated current, press MENU or EXIT.

5.4 CONFIGURING ALARMS AND ASSIGNING SETPOINTS.

5.4.1 Purpose

The Model FCL analyzer has an optional alarm relay board. This section describes how to configure and assign setpoints to the alarm relays, simulate alarm action, and synchronize interval timers. CONFIGURE THE ALARMS FIRST.

1.Configuring an alarm means…

a. Assigning a sensor and measurement (chlorine, pH, or temperature) to an alarm. An alarm relay can also be used as a timer.

b.Selecting high or low logic. c. Choosing a deadband.

d.Setting the interval timer parameters.

2.Simulating an alarm means making the analyzer energize or de-energize an alarm relay.

25

Image 35

Emerson PN 51-FCL-1056 RangeSimulate, Configure Simulate, Output, 00 mA, Configuring Alarms and Assigning Setpoints

Contents

FCL with 1056 Analyzer Essential Instructions ORP EnglishFree Chlorine Ppm mg/L S1 Manual pH Temp Units S1 Free Cl PH Correction ManualLive/Continous Sensor 2 pH Menu TreeCalibrate Sensor 1 Free chlorine Reset Analyzer AlarmsTemperature Diagnostic Setup Rev. Level Date About This Document FCL-1056 Table of Contents List of Tables Table of Contents CONT’D Iii List of Tables CONT’D Applications Section Description and SpecificationsFeatures Specifications Analyzer Specifications GeneralSpecifications Sensor PH Correction required selection AccessoriesOrdering Information Component Parts This page left blank intentionally FCL-02 free chlorine with continuous pH correction Section InstallationUnpacking and Inspection FCL-01 free chlorine without continuous pH correction Mounting, Inlet, and Drain Connections InstallationInstalling the Sensors General Information Model FCL-01 This page left blank intentionally Analog output wiring Section WiringPOWER, ALARM, and Output Wiring Power Alarm relay connections Sensor Wiring Wiring Diagram for Free Chlorine Sensor Model FCL-1056 Section Wiring Display Section Display and Operation Keypad Range Programming the ANALYZER-TUTORIALCalibrate Outputs Security Output Range O1 S1 4mA 0.000 ppmO1 S1 20mA 08.50 ppm O2 S1 4mA 0.0C O2 S1 20mA 100.0C Hold Using Hold Format, Language, Warning, and Contrast Configuring the Main DisplayMain Format Language English Contrast General Default SettingsSection Programming the Analyzer Sensor assignment Alarms Choices Default Definitions CONFIGURING, RANGING, and Simulating Outputs Assign ConfigureProgramOutput O1 S1 20mA 10.00 ppm O2 S1 4mA 0.0C O2 S1 20mA 100.0C Configure Simulate Output ConfigureProcedure Ranging Outputs Output Output Range Output Configure SimulateConfiguring Alarms and Assigning Setpoints RangeSimulate Section Programming the Analyzer Alarm AlarmsConfigure/Setpoint Don’t Simulate Alarms Configure/SetpointAlarm Simulate Alarm Simulate Procedure Synchronizing Timers Alarms Configure/Setpoint SimulateSynch Timers Yes Definitions pH/ORP Configuring the MeasurementDefinitions Chlorine Sensor1Sensor Measurement Definitions pH Configuring Temperature Related Settings S1 Temp Comp Auto S2 Temp Comp Program Outputs Alarms MeasurementTemperature Configuring Security Settings Security Program Alarms Measurement TemperatureSetting UP Diagnostics Security Procedure Setting Up Diagnostics Program Measurement Temperature SecurityDiagnostic Setup GI Fault High 1500MΩ Reset Analyzer Resetting the AnalyzerProgram Temperature Security Diagnostics Reset Analyzer Introduction Calibrating TemperatureSection Calibration S1 Calibration + 25.0C ProcedureCalibrate SensorSensor11 Output S1 Calibration Calibration Free Chlorine Procedure-Zeroing the Sensor Choose Free Chlorine Calibrate SensorSensor11 Output S1 Calibration Sensor Output Temperature S1 Calibration ZeroZeroCalCal Process CalCalibrate? Sensor Calibration Slope and Offset Calibration pH Auto ZeroBufferCalCal Stable Time 07.01 pH10.01 pH Buffer Manual Manual Buffer 1 0 7.00 pH S2 pH Manual Cal Buffer S1 Enter Value 00 pH Redox Temperature S2 pH Cal Buffer CalStandardizeStandardize Slope 56.19 mV/pH Offset Procedure-Entering a Known Slope and Offset MA Output Cal Meter 000 mA Trim Complete Calibration Analog OutputsOutput This page left blank intentionally Section Digital Communications Model FCL-1056 Section Analyzer Section Maintenance General Cleaning the membraneReplacing the electrolyte solution and membrane Chlorine Sensor PH Sensor Cleaning the SensorOther Maintenance Constant Head Flow Controller Cleaning the flow controller Weight Weight Overview Section TroubleshootingUsing the Diagnostic Feature Faults Hardware Error Troubleshooting When a Fault Message is ShowingFault message Explanation Section Sensor RTD Open Sensor CPU ErrorSensor ADC Error Sensor Incompatible Broken Glass Sensor RTD Out of RangeGlass Z Too High Reference Impedance Too High Troubleshooting When a Warning Message is Showing Troubleshooting When no Error Message is Showing Chlorine Readings drift Sensor can be calibrated, but the current is too lowProcess readings are erratic Chlorine readings are too low Sensor does not respond to changes in chlorine level Calibration Error During Two-Point Calibration Troubleshooting When no Error Message is Showing pH Sensor Does Not Respond to Known pH Changes Calibration Error during Standardization PH Readings Are Moderately Noisy and Tend to Wander Cath Troubleshooting When no Error Message is Showing GeneralSimulating Inputs Chlorine Anod Simulating pH input Simulating Inputs pH Simulating temperature Simulating Inputs TemperaturePage Germany Americas HeadquartersASIA-PACIFIC Europe Warranty Specifications subject to change without notice