Redox Temperature S2 pH Cal | Emerson PN 51-FCL-1056 specs

MODEL FCL-1056	SECTION 6.0
	CALIBRATION

6.4.6 Procedure-Entering a Known Slope and Offset

1.Calibration data, i.e., slope and offset at pH 7, can be entered directly into the analyzer if the data for the sensor are already known.

Calibrate?

Sensor 1

Sensor 2

Output 1

Output 2

2.Press MENU. The main menu screen appears. The cursor will be on Calibrate. Press ENTER.

3.Choose the sensor you wish to calibrate. Sensor 1 is the chlorine sensor. Sensor 2 is the pH sensor.

S2 Calibration

pHpH

ORP

Redox Temperature

S2 pH Cal

ZeroBufferCalCal

Standardize

Slope:	56.19 mV/pH
Offset:	2 mV

4. Choose pH.

5.Choose Slope or Offset. Enter the known slope and offset values. Always enter the slope as a positive number. Press ENTER to store the number. See Section 6.4.2 for more information.

6.To return to the main display, press MENU then EXIT.

48

Image 58

Emerson PN 51-FCL-1056 instruction manual Redox Temperature S2 pH Cal, Procedure-Entering a Known Slope and Offset

Contents

FCL with 1056 Analyzer Essential Instructions Ppm mg/L EnglishFree Chlorine ORP Live/Continous S1 Free Cl PH Correction ManualS1 Manual pH Temp Units Calibrate Sensor 1 Free chlorine Menu TreeSensor 2 pH Diagnostic Setup AlarmsTemperature Reset Analyzer About This Document Rev. Level Date Table of Contents FCL-1056 Table of Contents CONT’D List of Tables List of Tables CONT’D Iii Features Section Description and SpecificationsApplications Specifications Sensor Specifications GeneralSpecifications Analyzer Component Parts AccessoriesOrdering Information PH Correction required selection This page left blank intentionally FCL-01 free chlorine without continuous pH correction Section InstallationUnpacking and Inspection FCL-02 free chlorine with continuous pH correction General Information InstallationInstalling the Sensors Mounting, Inlet, and Drain Connections Model FCL-01 This page left blank intentionally Power Section WiringPOWER, ALARM, and Output Wiring Analog output wiring Sensor Wiring Alarm relay connections Wiring Diagram for Free Chlorine Sensor Model FCL-1056 Section Wiring Section Display and Operation Display Keypad Outputs Programming the ANALYZER-TUTORIALCalibrate Range O2 S1 4mA 0.0C O2 S1 20mA 100.0C Output Range O1 S1 4mA 0.000 ppmO1 S1 20mA 08.50 ppm Security Using Hold Hold Language English Contrast Configuring the Main DisplayMain Format Format, Language, Warning, and Contrast Section Programming the Analyzer Default SettingsGeneral Alarms Sensor assignment Choices Default CONFIGURING, RANGING, and Simulating Outputs Definitions ProgramOutput ConfigureAssign Output Output Range Configure Simulate Output ConfigureProcedure Ranging Outputs O1 S1 20mA 10.00 ppm O2 S1 4mA 0.0C O2 S1 20mA 100.0C RangeSimulate Configure SimulateConfiguring Alarms and Assigning Setpoints Output Section Programming the Analyzer Configure/Setpoint AlarmsAlarm Simulate Alarms Configure/SetpointAlarm Simulate Alarm Don’t Simulate Synch Timers Yes Alarms Configure/Setpoint SimulateProcedure Synchronizing Timers Definitions Chlorine Configuring the MeasurementDefinitions pH/ORP Measurement Sensor1Sensor Configuring Temperature Related Settings Definitions pH Configuring Security Settings Program Outputs Alarms MeasurementTemperature S1 Temp Comp Auto S2 Temp Comp Security Program Alarms Measurement TemperatureSetting UP Diagnostics Security GI Fault High 1500MΩ Program Measurement Temperature SecurityDiagnostic Setup Procedure Setting Up Diagnostics Reset Analyzer Resetting the AnalyzerProgram Temperature Security Diagnostics Reset Analyzer Section Calibration Calibrating TemperatureIntroduction S1 Calibration ProcedureCalibrate SensorSensor11 Output S1 Calibration + 25.0C Procedure-Zeroing the Sensor Calibration Free Chlorine Calibrate SensorSensor11 Output S1 Calibration Choose Free Chlorine Sensor Temperature S1 Calibration ZeroZeroCalCal Process CalCalibrate? Sensor Output Calibration pH Calibration Slope and Offset ZeroBufferCalCal Auto 10.01 pH 07.01 pHStable Time Manual Buffer Manual Buffer 1 0 7.00 pH S2 pH Manual Cal Buffer Slope 56.19 mV/pH Offset Redox Temperature S2 pH Cal Buffer CalStandardizeStandardize S1 Enter Value 00 pH Procedure-Entering a Known Slope and Offset Output Calibration Analog OutputsMA Output Cal Meter 000 mA Trim Complete This page left blank intentionally Section Digital Communications Model FCL-1056 Section Section Maintenance Analyzer Chlorine Sensor Cleaning the membraneReplacing the electrolyte solution and membrane General Other Maintenance Cleaning the SensorPH Sensor Cleaning the flow controller Constant Head Flow Controller Weight Weight Faults Section TroubleshootingUsing the Diagnostic Feature Overview Fault message Explanation Section Troubleshooting When a Fault Message is ShowingHardware Error Sensor Incompatible Sensor CPU ErrorSensor ADC Error Sensor RTD Open Reference Impedance Too High Sensor RTD Out of RangeGlass Z Too High Broken Glass Troubleshooting When a Warning Message is Showing Troubleshooting When no Error Message is Showing Chlorine Process readings are erratic Sensor can be calibrated, but the current is too lowReadings drift Sensor does not respond to changes in chlorine level Chlorine readings are too low Troubleshooting When no Error Message is Showing pH Calibration Error During Two-Point Calibration Calibration Error during Standardization Sensor Does Not Respond to Known pH Changes PH Readings Are Moderately Noisy and Tend to Wander Anod Troubleshooting When no Error Message is Showing GeneralSimulating Inputs Chlorine Cath Simulating Inputs pH Simulating pH input Simulating Inputs Temperature Simulating temperaturePage Europe Americas HeadquartersASIA-PACIFIC Germany Warranty Specifications subject to change without notice