S1 Free Cl PH Correction Manual | Emerson PN 51-FCL-1056 guide

S1 Free Cl

pH Correction

Manual

Live/Continous

S1 Manual pH

07.00

Temp Units

oC

oF

9. Choose Live/Continuous. Go to step 11.

10.The screen shown at left appears only if you have an FCL-01. Enter the pH of the process liquid.

11. Choose the desired temperature units.

12.The main display appears. The outputs and alarms (if an alarm board is present) are assigned to default values.

13.To change outputs, alarms, and other settings go to the main menu and choose Program. Follow the prompts. A menu tree is on the following two pages. To calibrate the sensor(s) refer to section 6.0.

Image 4

Emerson PN 51-FCL-1056 instruction manual S1 Free Cl PH Correction Manual, Live/Continous, S1 Manual pH Temp Units

Contents

FCL with 1056 Analyzer Essential Instructions English Free ChlorinePpm mg/L ORP Live/Continous S1 Free Cl PH Correction ManualS1 Manual pH Temp Units Calibrate Sensor 1 Free chlorine Menu TreeSensor 2 pH Alarms TemperatureDiagnostic Setup Reset Analyzer About This Document Rev. Level Date Table of Contents FCL-1056 Table of Contents CONT’D List of Tables List of Tables CONT’D Iii Features Section Description and SpecificationsApplications Specifications Sensor Specifications GeneralSpecifications Analyzer Accessories Ordering InformationComponent Parts PH Correction required selection This page left blank intentionally Section Installation Unpacking and InspectionFCL-01 free chlorine without continuous pH correction FCL-02 free chlorine with continuous pH correction Installation Installing the SensorsGeneral Information Mounting, Inlet, and Drain Connections Model FCL-01 This page left blank intentionally Section Wiring POWER, ALARM, and Output WiringPower Analog output wiring Sensor Wiring Alarm relay connections Wiring Diagram for Free Chlorine Sensor Model FCL-1056 Section Wiring Section Display and Operation Display Keypad Programming the ANALYZER-TUTORIAL CalibrateOutputs Range Output Range O1 S1 4mA 0.000 ppm O1 S1 20mA 08.50 ppmO2 S1 4mA 0.0C O2 S1 20mA 100.0C Security Using Hold Hold Configuring the Main Display Main FormatLanguage English Contrast Format, Language, Warning, and Contrast Section Programming the Analyzer Default SettingsGeneral Alarms Sensor assignment Choices Default CONFIGURING, RANGING, and Simulating Outputs Definitions ProgramOutput ConfigureAssign Configure Simulate Output Configure Procedure Ranging OutputsOutput Output Range O1 S1 20mA 10.00 ppm O2 S1 4mA 0.0C O2 S1 20mA 100.0C Configure Simulate Configuring Alarms and Assigning SetpointsRangeSimulate Output Section Programming the Analyzer Configure/Setpoint AlarmsAlarm Alarms Configure/Setpoint Alarm Simulate AlarmSimulate Don’t Simulate Synch Timers Yes Alarms Configure/Setpoint SimulateProcedure Synchronizing Timers Definitions Chlorine Configuring the MeasurementDefinitions pH/ORP Measurement Sensor1Sensor Configuring Temperature Related Settings Definitions pH Program Outputs Alarms Measurement TemperatureConfiguring Security Settings S1 Temp Comp Auto S2 Temp Comp Program Alarms Measurement Temperature Setting UP DiagnosticsSecurity Security Program Measurement Temperature Security Diagnostic SetupGI Fault High 1500MΩ Procedure Setting Up Diagnostics Resetting the Analyzer Program Temperature Security DiagnosticsReset Analyzer Reset Analyzer Section Calibration Calibrating TemperatureIntroduction Procedure Calibrate SensorSensor11 OutputS1 Calibration S1 Calibration + 25.0C Procedure-Zeroing the Sensor Calibration Free Chlorine Calibrate SensorSensor11 Output S1 Calibration Choose Free Chlorine Temperature S1 Calibration ZeroZeroCalCal Process Cal Calibrate?Sensor Sensor Output Calibration pH Calibration Slope and Offset ZeroBufferCalCal Auto 10.01 pH 07.01 pHStable Time Manual Buffer Manual Buffer 1 0 7.00 pH S2 pH Manual Cal Buffer Redox Temperature S2 pH Cal Buffer Cal StandardizeStandardizeSlope 56.19 mV/pH Offset S1 Enter Value 00 pH Procedure-Entering a Known Slope and Offset Output Calibration Analog OutputsMA Output Cal Meter 000 mA Trim Complete This page left blank intentionally Section Digital Communications Model FCL-1056 Section Section Maintenance Analyzer Cleaning the membrane Replacing the electrolyte solution and membraneChlorine Sensor General Other Maintenance Cleaning the SensorPH Sensor Cleaning the flow controller Constant Head Flow Controller Weight Weight Section Troubleshooting Using the Diagnostic FeatureFaults Overview Fault message Explanation Section Troubleshooting When a Fault Message is ShowingHardware Error Sensor CPU Error Sensor ADC ErrorSensor Incompatible Sensor RTD Open Sensor RTD Out of Range Glass Z Too HighReference Impedance Too High Broken Glass Troubleshooting When a Warning Message is Showing Troubleshooting When no Error Message is Showing Chlorine Process readings are erratic Sensor can be calibrated, but the current is too lowReadings drift Sensor does not respond to changes in chlorine level Chlorine readings are too low Troubleshooting When no Error Message is Showing pH Calibration Error During Two-Point Calibration Calibration Error during Standardization Sensor Does Not Respond to Known pH Changes PH Readings Are Moderately Noisy and Tend to Wander Troubleshooting When no Error Message is Showing General Simulating Inputs ChlorineAnod Cath Simulating Inputs pH Simulating pH input Simulating Inputs Temperature Simulating temperaturePage Americas Headquarters ASIA-PACIFICEurope Germany Warranty Specifications subject to change without notice