Program Outputs, Alarms, Measurement | Emerson PN 51-FCL-1056

MENU TREE (continued)

Program

Outputs

Range (assign values to 4 and 20 mA)

Configure

Output 1 or 2

Assign sensor and measurement

Range

Scale

Dampening

Fault mode (fixed or live)

Fault value (output current)

Simulate

Alarms

Configure/Setpoint

Alarm 1, 2, 3, or 4

Setpoint

Assign sensor and measurement

High or low logic

Deadband

Interval time

On time

Recovery time

Simulate

Synchronize timers

Measurement

Free chlorine (sensor 1) Measurement selection Units

Filter Resolution

pH (sensor 2)

Measurement selection Preamplifier location Solution temperature correction Resolution

Filter

Reference impedance (high or low)

Temperature

Units

Temperature compensation (auto or manual)

Set manual temperature (if selected)

Security

Calibrate/Hold only

All

Diagnostic Setup

Reference Offset

Diagnostics (on or off)

Glass impedance temperature correction

Glass fault high

Reference fault high

Reset Analyzer

Image 6

Emerson PN 51-FCL-1056 Program Outputs, Alarms, Measurement, Temperature, Security, Diagnostic Setup, Reset Analyzer

Contents

FCL with 1056 Analyzer Essential Instructions Ppm mg/L EnglishFree Chlorine ORP S1 Free Cl PH Correction Manual Live/ContinousS1 Manual pH Temp Units Menu Tree Calibrate Sensor 1 Free chlorineSensor 2 pH Diagnostic Setup AlarmsTemperature Reset Analyzer About This Document Rev. Level Date Table of Contents FCL-1056 Table of Contents CONT’D List of Tables List of Tables CONT’D Iii Section Description and Specifications FeaturesApplications Specifications General Specifications SensorSpecifications Analyzer Component Parts AccessoriesOrdering Information PH Correction required selection This page left blank intentionally FCL-01 free chlorine without continuous pH correction Section InstallationUnpacking and Inspection FCL-02 free chlorine with continuous pH correction General Information InstallationInstalling the Sensors Mounting, Inlet, and Drain Connections Model FCL-01 This page left blank intentionally Power Section WiringPOWER, ALARM, and Output Wiring Analog output wiring Sensor Wiring Alarm relay connections Wiring Diagram for Free Chlorine Sensor Model FCL-1056 Section Wiring Section Display and Operation Display Keypad Outputs Programming the ANALYZER-TUTORIALCalibrate Range O2 S1 4mA 0.0C O2 S1 20mA 100.0C Output Range O1 S1 4mA 0.000 ppmO1 S1 20mA 08.50 ppm Security Using Hold Hold Language English Contrast Configuring the Main DisplayMain Format Format, Language, Warning, and Contrast Default Settings Section Programming the AnalyzerGeneral Alarms Sensor assignment Choices Default CONFIGURING, RANGING, and Simulating Outputs Definitions Configure ProgramOutputAssign Output Output Range Configure Simulate Output ConfigureProcedure Ranging Outputs O1 S1 20mA 10.00 ppm O2 S1 4mA 0.0C O2 S1 20mA 100.0C RangeSimulate Configure SimulateConfiguring Alarms and Assigning Setpoints Output Section Programming the Analyzer Alarms Configure/SetpointAlarm Simulate Alarms Configure/SetpointAlarm Simulate Alarm Don’t Simulate Alarms Configure/Setpoint Simulate Synch Timers YesProcedure Synchronizing Timers Configuring the Measurement Definitions ChlorineDefinitions pH/ORP Measurement Sensor1Sensor Configuring Temperature Related Settings Definitions pH Configuring Security Settings Program Outputs Alarms MeasurementTemperature S1 Temp Comp Auto S2 Temp Comp Security Program Alarms Measurement TemperatureSetting UP Diagnostics Security GI Fault High 1500MΩ Program Measurement Temperature SecurityDiagnostic Setup Procedure Setting Up Diagnostics Reset Analyzer Resetting the AnalyzerProgram Temperature Security Diagnostics Reset Analyzer Calibrating Temperature Section CalibrationIntroduction S1 Calibration ProcedureCalibrate SensorSensor11 Output S1 Calibration + 25.0C Procedure-Zeroing the Sensor Calibration Free Chlorine Calibrate SensorSensor11 Output S1 Calibration Choose Free Chlorine Sensor Temperature S1 Calibration ZeroZeroCalCal Process CalCalibrate? Sensor Output Calibration pH Calibration Slope and Offset ZeroBufferCalCal Auto 07.01 pH 10.01 pHStable Time Manual Buffer Manual Buffer 1 0 7.00 pH S2 pH Manual Cal Buffer Slope 56.19 mV/pH Offset Redox Temperature S2 pH Cal Buffer CalStandardizeStandardize S1 Enter Value 00 pH Procedure-Entering a Known Slope and Offset Calibration Analog Outputs OutputMA Output Cal Meter 000 mA Trim Complete This page left blank intentionally Section Digital Communications Model FCL-1056 Section Section Maintenance Analyzer Chlorine Sensor Cleaning the membraneReplacing the electrolyte solution and membrane General Cleaning the Sensor Other MaintenancePH Sensor Cleaning the flow controller Constant Head Flow Controller Weight Weight Faults Section TroubleshootingUsing the Diagnostic Feature Overview Troubleshooting When a Fault Message is Showing Fault message Explanation SectionHardware Error Sensor Incompatible Sensor CPU ErrorSensor ADC Error Sensor RTD Open Reference Impedance Too High Sensor RTD Out of RangeGlass Z Too High Broken Glass Troubleshooting When a Warning Message is Showing Troubleshooting When no Error Message is Showing Chlorine Sensor can be calibrated, but the current is too low Process readings are erraticReadings drift Sensor does not respond to changes in chlorine level Chlorine readings are too low Troubleshooting When no Error Message is Showing pH Calibration Error During Two-Point Calibration Calibration Error during Standardization Sensor Does Not Respond to Known pH Changes PH Readings Are Moderately Noisy and Tend to Wander Anod Troubleshooting When no Error Message is Showing GeneralSimulating Inputs Chlorine Cath Simulating Inputs pH Simulating pH input Simulating Inputs Temperature Simulating temperaturePage Europe Americas HeadquartersASIA-PACIFIC Germany Warranty Specifications subject to change without notice