H50 SERIES GAS FRYERS

CHAPTER 1: SERVICE PROCEDURES

1.1Functional Description

H50 Series fryers contain a welded stainless steel frypot that is directly heated by a high efficiency infrared burner system requiring approximately 43% less energy than conventional burners to cook the same volume.

Self-contained combustion chambers (referred to as “burners”) are fitted into rails attached to the sides of the frypot, one on each side. Each combustion chamber is fitted with special ceramic tiles that are heated by the burning of a forced air/gas mixture. The tiles transfer their heat to the frypot by means of infrared radiation, providing much more constant and uniform heat dispersion over the surface of the frypot than do conventional burners. Because less heat is lost to the atmosphere in the process, compared to “open-burner” designs, less fuel is required to achieve and maintain a given frypot temperature.

In full vat units, gas flow to both of the burners is regulated by one electromechanical gas valve. In dual vat units, each burner has its own valve. All fryers in this series are equipped with 24VAC gas valve systems, and all are configured with electronic ignition.

THE ELECTRONIC IGNITION SYSTEM

An ignition module mounted in the component box or “shield” (located behind the control panel) is connected to an ignitor assembly at the burner. The ignition module performs four important functions: it provides fuse protection for the 24-volt circuit, provides an ignition spark, supplies voltage to the gas valve, and proofs the burner flame. The module contains a 4-second time delay circuit and a coil that activates the gas valve. Three types are in use. A closed-box design is used in most fryers, but in some fryers built for export the module resembles an interface board. A single dual-spark module is used on current production full-vat fryers. Two single-spark modules were used on full-vat fryers built before August 2000. All dual-vat fryers use two single-spark modules.

Inside the Ignition Module

Out to

Gas Valve

To Alarm

25 V +

Coil

TD

HV

GND

Ignition Wire

Flame Sensor

The ignitor assembly consists of a spark plug, an enrichment tube, and a flame sensor.

At start-up, the power switch is placed in the ON position, supplying approximately 12-volts DC to the heat control circuitry in the controller or computer and to one side of the heat relay coils on the interface board. If resistance in the temperature probe indicates the temperature in the frypot is below 180ºF (82ºC), the current flows through a melt cycle circuit where a timer switch alternately closes for 6 seconds and opens for 24 seconds. If the temperature is 180ºF (82ºC) or above, the current flows through a heat circuit, bypassing the timer switch. In either case, ground is supplied to

1-1

Page 7
Image 7
Frymaster manual H50 Series GAS Fryers Service Procedures, Functional Description

H50 Series specifications

The Frymaster H50 Series represents a significant advancement in commercial deep frying technology, designed specifically for high-volume food service operations. With a focus on efficiency, ease of use, and exceptional frying quality, this series is a favorite among restaurateurs seeking to optimize their kitchen performance.

One of the standout features of the Frymaster H50 Series is its Energy Efficiency. These fryers are engineered to provide superior heat transfer, allowing for quicker recovery times and reduced energy consumption. This is crucial in a busy kitchen where every second counts, and maintaining consistent oil temperatures is vital for producing perfectly cooked food.

The H50 Series incorporates the advanced computer control platform, which offers precise temperature control and monitoring. This technology allows operators to set specific frying times and temperatures for various foods, ensuring consistency and quality in every batch. Additionally, these controls include built-in safety features that help prevent overheating and potential hazards, promoting a safer working environment.

Flexibility is another hallmark of the H50 Series. These fryers can accommodate a wide range of menu items, from fries to chicken and seafood, making them an ideal choice for diverse culinary applications. The fryers also come with adjustable basket configurations and options for single or multiple frying pots, providing versatility for varying production demands.

The design of the Frymaster H50 Series is focused on ease of use and maintenance. The fryers feature a user-friendly interface, making it simple for staff to operate them even during peak hours. Maintenance is streamlined through easy access to components, ensuring that cleaning and servicing can be carried out quickly, minimizing downtime and enhancing productivity.

Durability is another key characteristic of the Frymaster H50 Series. Constructed with high-quality materials, these fryers are built to withstand the rigors of a commercial kitchen. The stainless steel exterior not only adds to the aesthetic appeal but also offers resistance to corrosion and damage, ensuring that these fryers will perform reliably over time.

In summary, the Frymaster H50 Series combines energy efficiency, advanced technology, operational flexibility, ease of use, and durability. This makes it a top choice for food service establishments aiming to deliver high-quality, consistently fried foods while optimizing kitchen operations. Whether you're upgrading your current equipment or starting a new venture, the H50 Series is a powerful ally in the world of commercial frying.