Bell crank and cam with basket lift link shown in down position. Note microswitch in upper right corner.

A bell crank style basket lift consists of a cam and bell crank that are connected to the basket lift arm by a flat metal link. The cam is attached to a drive motor. The motor ro- tates the cam, thus raising or lowering the lift arm linked to the bell crank. A roller-activated microswitch is used to limit travel. When the roller in the microswitch is in contact with the cam, the motor is energized. As the cam rotates, the mi- croswitch roller eventually loses contact with the cam and the circuit is broken, de-energizing the motor.

Timing circuitry in the controller initiates and stops basket lift operation depending upon the variables programmed by the operator. When the product button is pressed, the timing circuitry activates a coil in the basket lift relay to supply power to the motor. The microswitch stops the motor at the

lift’s lower travel limit and the switch contacts are reversed. At the end of the programmed cooking time, the timing circuit activates the coil once more and the lift rises until the microswitch again loses contact with the cam, opening the circuit and stopping the motor.

Problems with either basket lift design can be grouped into three categories:

Binding/jamming problems

Motor and gear problems

Electronics problems

BINDING/JAMMING PROBLEMS

Noisy, jerky or erratic movement of the lifts is usually due to lack of lubrication of the rods and their bushings. Apply a light coat of Lubriplate® or similar lightweight white grease to the rod and bushings to correct the problem.

With the modular basket lift, another possible cause of binding is improper positioning of the motor, which prevents the gear from correctly engaging the teeth in the rod. To correct the problem, loosen the screws that hold the motor in place and move it forward or backward until the rod has just enough slack to be rotated slightly.

MOTOR AND GEAR PROBLEMS

With the modular basket lift, the most likely problem to be encountered in this category is erratic motion of the lift due to a worn drive gear. Failure to keep the lift rod and bushings properly lubricated will cause unnecessary wear of the gear. The problem is corrected by replacing the worn gear.

If the lift cycles correctly but fails to remain in the up position (i.e., goes up, but then slowly settles back down into the frypot), the problem is a failed motor brake. A failed motor brake cannot be repaired and requires replacement of the motor itself.

1-31

Page 37
Image 37
Frymaster H50 Series manual BINDING/JAMMING Problems

H50 Series specifications

The Frymaster H50 Series represents a significant advancement in commercial deep frying technology, designed specifically for high-volume food service operations. With a focus on efficiency, ease of use, and exceptional frying quality, this series is a favorite among restaurateurs seeking to optimize their kitchen performance.

One of the standout features of the Frymaster H50 Series is its Energy Efficiency. These fryers are engineered to provide superior heat transfer, allowing for quicker recovery times and reduced energy consumption. This is crucial in a busy kitchen where every second counts, and maintaining consistent oil temperatures is vital for producing perfectly cooked food.

The H50 Series incorporates the advanced computer control platform, which offers precise temperature control and monitoring. This technology allows operators to set specific frying times and temperatures for various foods, ensuring consistency and quality in every batch. Additionally, these controls include built-in safety features that help prevent overheating and potential hazards, promoting a safer working environment.

Flexibility is another hallmark of the H50 Series. These fryers can accommodate a wide range of menu items, from fries to chicken and seafood, making them an ideal choice for diverse culinary applications. The fryers also come with adjustable basket configurations and options for single or multiple frying pots, providing versatility for varying production demands.

The design of the Frymaster H50 Series is focused on ease of use and maintenance. The fryers feature a user-friendly interface, making it simple for staff to operate them even during peak hours. Maintenance is streamlined through easy access to components, ensuring that cleaning and servicing can be carried out quickly, minimizing downtime and enhancing productivity.

Durability is another key characteristic of the Frymaster H50 Series. Constructed with high-quality materials, these fryers are built to withstand the rigors of a commercial kitchen. The stainless steel exterior not only adds to the aesthetic appeal but also offers resistance to corrosion and damage, ensuring that these fryers will perform reliably over time.

In summary, the Frymaster H50 Series combines energy efficiency, advanced technology, operational flexibility, ease of use, and durability. This makes it a top choice for food service establishments aiming to deliver high-quality, consistently fried foods while optimizing kitchen operations. Whether you're upgrading your current equipment or starting a new venture, the H50 Series is a powerful ally in the world of commercial frying.