Configuration Parameters | GE EPM 5300, EPM 5200, EPM 5350 specs

CHAPTER 16: ETHERNET OPTION

ETHERNET OPTION SETUP

Use a Telnet connection to configure the unit over the network. The Ethernet Interface’s configuration is stored in nonvolatile memory (NVRam) and is retained without power. The configuration can be changed at any time. The Ethernet Interface performs a reset after the configuration has been changed and stored.

As mentioned above, to configure the Ethernet Interface over the network, establish a Telnet connection to port 9999. From the Windows Start menu, click Run and type the following command, where x.x.x.x is the IP address and 9999 is the Ethernet Interface’s fixed network configuration port number.

telnet x.x.x.x 9999

Be sure to include a space between the IP address and 9999.

16.2.5Configuration Parameters

After entering Setup Mode (confirm by pressing Enter), you an configure the parameters by entering one of the numbers on the Change Setup Menu, or you can confirm default values by pressing Enter. Be sure to store new configurations when you are finished. The Ethernet Interface will then perform a power reset.

Serial Number 5415404 MAC Address 00:20:4A:54:3C:2C

Software Version V01.2 (000719)

Press Enter to go into Setup Mode

1.Network/IP Settings:

	Ethernet Interface Autodetect
	IP Address	- 0.0.0.0/DHCP (Customer Configurable)
	Default Gateway	--- not set --- (Customer Configurable)
	Netmask	--- not set --- (Customer Configurable)
2.	Serial & Mode Settings:
	Protocol	Modbus/RTU, Slave(s) attached (FIXED)
	Serial Interface	9600,8,N,1,RS232,DB25 (must match meter)
		(FIXED)
3.	Modem Control Settings:
	DCD Output	Fixed High/Active
	CTS Output	Fixed High Active

4.Advanced Modbus Protocol Settings:

Slave Addr/Unit Id Source	Modbus/TCP header (FIXED)
Modbus Serial Broadcasts	Disabled
Character, Message Timeout	00010 ms, 00500 ms

D)default settings, S) save, Q) quit without save; select command or parameter set (1..4) to change: I

EPM 5300 SERIES ADVANCED POWER METERS – INSTRUCTION MANUAL

16–121

Image 133

GE EPM 5300, EPM 5200, EPM 5350 instruction manual Configuration Parameters

Contents

GE Multilin EPM 5300 Power Metering System ChapterPage Table of Contents Programming 112 111113 114 Table of Contents TOC-IV Single Phase System EPM 5300 Series Meters AC Power Measurement = E I cosΘ Power W in a single phase system is Delta Wye Three-Phase System Poly Phase System 1 Delta, 2 Wye Consumption WH = W ⋅ T Consumption, Demand and Poor Power Factor Sin ω ⋅ t Waveform and Harmonics Mechanical Installation EPM 5300 Series Meters Mechanical Installation Installation with K-110 option for limited space conditions Port Mechanical Installation Connecting the Current Circuit EPM 5300 Series Meters Electrical InstallationFeet CT Connection Option 1 Isolating a CT Connection Reversal power readingHelpful Debugging Tools Connecting the Voltage Circuit Selecting the Voltage Fuses Externally fuse power supply with a slow-blow 3 Amp fuse Connection to the Main Power Supply List of Connection Diagrams Electrical Connection Installation Line Load Back View Line Back View B C Load Line B C Back View Load EPM 5300P-S Single Phase with CT and PT Connection Line EPM 5300P Relay Overview Relay, Protection and Pulse Output2 2 Relays & 1 KYZ Pulse Output -NL Option This section applies only to the -NL or -NL2 Relay Option Close-up of the Relay and KYZ pulse output on the rear panel Standard Rate Table for Watts Standard Rate Table for Watts KYZ Pulse Outputs NL2 Option KYZ Pulse Outputs NL2 Option RS-232C EPM 5300 Series Meters Communication Installation RS-485 RS-485 Hookup Diagram 2 wire Half Duplex RS-485 Hookup Diagram 2 wire Half Duplex Closed Loop Connecting 4-Wire bus to RS-485 Port RS-485 Hookup Diagram 4 wire Full Duplex RS-485 Hookup Diagram 4 wire Full Duplex Detail View You may want to use a Modem Manager RS485-RS232 Converter Network of Instruments and Long Distance Communication Programming the Modem Modem Connected to Computer Originate ModemModem Connected to the Device Remote Modem Debugging Communication Problems Tell modem to write the new settings to activate profile Freq EPM 5300 Series Meters Overview± Total KWH Total Kvah N/A on EPM 5200P EPM 5300P front panel with display and keypad Press Power to select the power category Accessing the Power FunctionsSequence Press PHASE/NEXT for the desired phase Accessing Voltage and Current Phases Display blanks and indicates the %THD value momentarily Accessing %THD Functions Viewing Individual Phase Indication for Power Functions Phase Accessing Max/Min Values Unprotected Reset Resetting ValuesTo reset the min of Amps a Repeat this procedure for each value you wish to reset Password is Protected Reset Press Power once Resetting Hour ReadingsTime a password digit Appears While the question To view the setup of the LM1/LM2 set limits Accessing the LM1/LM2 Set LimitsTo access the set limit To locate readings that exceeded Limit Voltage Phase Reversal Voltage Phase Reversal and ImbalanceThis display indicates a Press and hold down Enter Programming Mode see Programming Section Access ModesPrint Operating Data Print Programming Data Print Operating Data Press and hold PHASE/NEXTMiddle display Release both buttons Print Programming Data Step Press and hold PHASE/NEXT Accessing Firmware Version/LED Test EPM 5300 Series Meters Programming Overview General Procedure GROUPS, Functions, and Switch Packs Switch Packs Point from Function and Group level Programming Mode Data EntryPosition UP or Down Activates new data entry and enters or exits from Standard Numeric Data Entry EPM 5200P EPM 5300 Series Meters EPM 5200P VA/HR EPM 5300P vs EPM 5200P vs EPM 5350P Checksum Error-Protective Self-Checking Algorithms EPM 5300 Series Meters Entering Programming Mode Entering Programming Mode Password EntryIf 3 is not already displayed Press Amps until 3 appears Flashes momentarily in middle display Relay 1 Set-up / Time delay System Configuration see TableRelay 2 Set-up / Time delay Number of Phases Lower display indicates current Interval setting Enter Group Level of Programming Mode see ChpGroup 0, Function 0-The Integration Interval Press Amps to activate the Group To change the Meter Address Programming Group 0 Global Meter Setup Group 0, Function 2 Baud Rate Group Function Pack Group 0, Function 3 System Configuration Open Delta System Installation Programming Programming Group 0 Global Meter Setup Printing Option Modbus Plus Capability To change the System Configuration Switch Settings Group 0, Function 3-Programming Procedure Relay Mode Enter in Group 0, Function 4, Pack ‘p’, Segments C and D Programming Steps LI M IT S Relay 1 On to Off Delay Time To change Time DelaysRelay 1 Off to On Delay Time Relay 2 On to Off Delay Time To program Relay 2 To perform the KYZ Parameter Selection Group 0, Function 6-KYZ Parameter SelectionKYZ Parameters Enter Group Level of Programming Mode see Chp Applies to -NL2 Option only How to Use KYZ Pulse Value Table for MultiplicationKYZ Pulse Value Selection is Multiply by How to Use KYZ Pulse Value Table for Division To change the KYZ pulse value Enter 2 for single phase/two wire Group 0, Function 7-Number of PhasesEnter Group Level of Programming Mode. Chapter Press Amps to activate the Group Appears in upper display Formulas Group 1, Function Typical Full Scale Settings for VoltsVoltage Full Scale Group 1 Programming Format Press Amps to activate Group Appears in upper display Press MAX/MIN/LIMITS until 1. appears in upper displayPress Volts to move decimal point Press Amps to store 10-76 Full Scale Settings for Amps To change the Full Scale Settings Press Amps to begin Data Entry Sequence Entering the Scale Factor Decimal Point Selection Step Scale Selection and Decimal Placement for Watts Display To change the scale factor setting for wattage Entering the Scale Factor Step 10-82 EPM 5300 Series Meters Programming Group 2 Meter Calibration Group 2 Programming Format Calibration RequirementsHigh End Calibration-Volts AN, BN, CN High End Calibration-Amps A, B, C To change the calibration high end-Functions 0 Group 2, Functions Group 2, Functions For Amps Low End Function 11-87 11-88 LM1 and LM2 SET Limits EPM 5300 Series Meters Groups 4, 5 Set Limits Relays Trip Relay Time Delays & Relay Mode V O L T S A M P S Group 4 Functions 0-3-LM1/LM2 Set Limits Group 4 Programming Format Group 4 Programming Format for Limit ConditionGroup 4 Functions Group 4 Example for Function Group 5 Functions 0-7-LM1/LM2 Set Limits There are 3 switches to set with limitsGroup 5 Programming Format for Limit Condition Group 5 Functions Special CasesGroup 5 Example for Function Digit Up Digit Down 0120 Group 6 Programming Format For THD Limit Conditions Group 6 LM1/LM2 Set LimitsGroup 6 Functions Digit Up Digit Down 012.0 Group 6-Example for Function Group Limits or Relays Programming Procedure Limits or Relays Programming Procedure Press Amps once to Disable the Limit 12-100 Phase Imbalance Phase Reversal and Phase Imbalance Trip Relay Level ENABLE/DISABLE To change the phase reversal setting Group 7, Function 0-Voltage Phase Reversal DetectionVoltage Phase Reversal Detection Voltage Phase Imbalance 13-104 To change the percentage voltage phase imbalance Group 7, Function 1-Percentage Voltage Phase Imbalance Middle and lower displays indicate new settings Exiting Programming Mode EPM 5300 Series Meters Exiting Programming Mode Press Amps to exit from Function Level to Group Level Meter returns to Function Level EPM 5300 Series Meters Programming Quick Reference Entering the Programming Mode Data Entry Sequence Programming Groups Group 0 Global Meter Setup On to OFF delay time OFF to on delay time Group 1 Full Scale SetupVolts Full Scale Currents Full Scale Power Full Scale Group 2 Calibration Group 3 Calibration Ratios Group 5 Power Function LimitsGroup 4 Volt/Current Limits Group 6 THD Limits Group 8 DC output Calibration Group 7 Imbalance/Reversal LimitsDetect Reversal Imbalance percent Limit ⎯ Scroll Groups 89L. Low-End Calibration 89H. High-End Calibration⎯ Scroll Functions ⎯ Scroll Packs 15-116 EPM 5300 Series Meters Ethernet Option Ethernet Module AutoIP Ethernet Option Setup Network Configuration Network Port LoginARP on Unix Telnet to Port Configuration Parameters Baud Rate