FRP Proportioner | Graco ti18496b, ti18524d, ti18526c instruction

Instructions - Parts

FRP Proportioner

3A2012J

EN

Low emission internal/external mix gel coat and chop proportioners. For use with resin and catalyst in hazardous and non-hazardous locations.

For professional use only.

Important Safety Instructions

Read all warnings and instructions in this manual and all component manuals. Save all instructions.

See page 4 for model and agency approvals information. See page 83 for maximum working pressure and other specifications. For patent information, see www.graco.com/patents.

WARNING

FIRE AND EXPLOSION HAZARD

Oil left in the system at the factory can react with catalyst and create a fire or explosion.

•Flush before first use.

•Do not add catalyst to the catalyst reservoir until the system has been flushed.

ti18526c

	ti18524d	ti18496b
		ti18496b
Cart and Boom System	Wall Mount System	Cart System

		II 2 Gc T5

Image 1

Graco ti18496b, ti18524d, ti18526c specifications FRP Proportioner, Important Safety Instructions

Contents

FRP Proportioner Important Safety Instructions Contents Agency Approvals Related ManualsManual Description No Cart Cart, Mast, and Boom ModelsHose Length Ratio Accessories Skin Injection Hazard Toxic Fluid or Fumes Hazard 3A2012J Material Self-ignition Important Two-Component Material InformationChanging Materials Keep Resin and Catalyst Components Separate Typical Applications Overview Key Component Identification Air Control Panel Pressure relief/recirculation valve P relieves pres Air Motor and Resin Displacement PumpPressure relief/recirculation fluid outlet P1 place Pressurized fluid outlet on filter R connect fluid Catalyst Pump Components Catalyst Pump Solvent Flush Diaphragm Pump Solvent Flush SystemsSolvent Flush Asme and CE-Approved Pressure Pot Before Installation SetupLocation Requirements System Mounting Wall Mount Systems Only For systems bolting directly to wall not using a pole For cart and boom systems only, install legs System Assembly Spring Chain Roving Guides Deflector Plates Grounding Ground Wire Air Connections Connect Fluid and Air Lines Catalyst Pump Pressure Relief Valve Fill Supply Tanks Flush Before First UseSolvent Flush Connections if applicable Gun Connections Operation Pressure Relief Procedure and ShutdownTrigger Lock Boom Operation Operation For internal mix proportioners only, check solvent line Startup Prime Follow Pressure Relief Procedure and Shut- down on Operation 3A2012J Flush External mix systems 30-40 psi 0.21-0.28 MPa, 2.1-2.8 bar Spray Follow Pressure Relief Procedure and Shutdown on AAC Air Adjustment Setup Mode Run ModeDataTrak Operation Operation Solenoid Release Button Runaway Monitor Prime/Flush DiagnosticsCounter/Totalizer Display Diagnostic Codes Symbol Code Name Diagnosis Cause Disconnect DataTrak Replace DataTrak Battery or Fuse Components MaintenanceTask Schedule Inspect pump wetcup Daily Resin Pump Troubleshooting Spray pattern Mendations Fluid is too thin or too thick Repair Disconnect the Displacement PumpGeneral Information Align cylinder and adapter plate Reconnect the Displacement Pump Reconnect the Air Motor Disconnect the Air Motor Ti18456c Replace Pumpline Remove Catalyst Pump from System Repair Catalyst PumpDisassemble Catalyst Pump Repair Throat and Piston Seals Assemble Catalyst Pump Repair Foot Valve Catalyst Pump Details Systems System Parts 152 24M692 SPACER, ball joint Wall or Pole Mount KIT Wall or Pole Mount KIT Wall or Pole Mount KIT Quantity Carts System Parts Part Description Qty Wall or Pole Mount Kit, 16N918 Boom, 16N761 Air Panel Slave Pump Linkage, 16P125 Part Description 131 171 Resin Pumplines Air Motor and Pump for Resin Pumpline Connecting KitGun Coupling Collars 24F620 Resin FilterMesh Pack 16M736 Resin Supply Hose 3A2012J 922 930 940 Catalyst Slave Pumps Catalyst Pumps Installation Tools not shown 16P425 Catalyst Reservoir Cart not included in kit, shown for reference only Hose Bundles Quantity 16N014 and 16N015 Kits Accessory Parts Heater Kits16N0169, 16N017, 16N018, and 16N019 Kits Nipple Asme Pressure Pots, 2-gallon 16M893 and 5-gallon 16M894 Solvent Pressure Pot Kits Tube Asme and CE-Approved Pressure Pots, 16M874 and 16M875 Gallon 16M560 and 5-gallon 16M561 Solvent Diaphragm Pumps 16M881 DataTrak Upgrade Kit Carts for 55 Gallon Barrel, 16M896 16M961 Roving Box Bracket Gel Hose Extension HosesChop Hose For external gel Cart and Boom DimensionsTop View Wall/Pole Mount Cart Only Pumpline Wall Mounting Bracket Dimensions Technical Data Pumpline Technical Data 3A2012J Graco Information Graco Standard Warranty