Replace DataTrak Battery or Fuse | Graco ti18526c, ti18524d specs

Operation

Replace DataTrak Battery or Fuse

The battery and fuse must be replaced in a non-hazardous location.

Use only the following approved replacement batter- ies. Use of an unapproved battery will void Graco’s warranty and FM and Ex approvals.

•Ultralife lithium # U9VL

•Duracell alkaline # MN1604

•Energizer alkaline # 522

•Varta alkaline # 4922

Use only a Graco-approved replacement fuse. Order Part 24C580.

Replace Battery

1.Unscrew cable from the back of the reed switch assembly. See FIG. 33.

2.Remove the cable from the two cable clips.

4.Remove two screws on back of module to access battery.

5.Disconnect the used battery and replace with an approved battery. See FIG. 34.

Replace Fuse

1.Remove the screw, metal strap, and plastic holder.

2.Pull the fuse away from the board.

3.Replace with a new fuse.

Solenoid Cable

Connection

Fuse

Sensor Cable

Connection

ti11992a

FIG. 33. Disconnect DataTrak

3.Remove DataTrak module from bracket. Take mod- ule and attached cable to a non-hazardous location.

Battery

ti11994a

FIG. 34. DataTrak Battery and Fuse Location

38

3A2012J

Image 38

Graco ti18526c, ti18524d, ti18496b specifications Replace DataTrak Battery or Fuse, Disconnect DataTrak

Contents

Important Safety Instructions FRP Proportioner Contents Manual Description Related ManualsAgency Approvals Hose ModelsNo Cart Cart, Mast, and Boom Length Ratio Accessories Skin Injection Hazard Toxic Fluid or Fumes Hazard 3A2012J Changing Materials Important Two-Component Material InformationMaterial Self-ignition Keep Resin and Catalyst Components Separate Overview Typical Applications Component Identification Key Air Control Panel Pressure relief/recirculation fluid outlet P1 place Air Motor and Resin Displacement PumpPressure relief/recirculation valve P relieves pres Pressurized fluid outlet on filter R connect fluid Catalyst Pump Catalyst Pump Components Solvent Flush Asme and CE-Approved Pressure Pot Solvent Flush SystemsSolvent Flush Diaphragm Pump Location Requirements SetupBefore Installation System Mounting Wall Mount Systems Only For systems bolting directly to wall not using a pole System Assembly For cart and boom systems only, install legs Spring Chain Roving Guides Deflector Plates Ground Wire Grounding Connect Fluid and Air Lines Air Connections Catalyst Pump Pressure Relief Valve Solvent Flush Connections if applicable Flush Before First UseFill Supply Tanks Gun Connections Trigger Lock Pressure Relief Procedure and ShutdownOperation Boom Operation Operation Startup For internal mix proportioners only, check solvent line Follow Pressure Relief Procedure and Shut- down on Prime Operation 3A2012J Flush Spray External mix systems 30-40 psi 0.21-0.28 MPa, 2.1-2.8 bar AAC Air Adjustment Follow Pressure Relief Procedure and Shutdown on DataTrak Operation Run ModeSetup Mode Operation Runaway Monitor Solenoid Release Button Counter/Totalizer DiagnosticsPrime/Flush Display Diagnostic Codes Symbol Code Name Diagnosis Cause Replace DataTrak Battery or Fuse Disconnect DataTrak Task Schedule Inspect pump wetcup Daily MaintenanceComponents Troubleshooting Resin Pump Spray pattern Mendations Fluid is too thin or too thick General Information Disconnect the Displacement PumpRepair Reconnect the Displacement Pump Align cylinder and adapter plate Disconnect the Air Motor Reconnect the Air Motor Ti18456c Replace Pumpline Disassemble Catalyst Pump Repair Catalyst PumpRemove Catalyst Pump from System Repair Throat and Piston Seals Repair Foot Valve Assemble Catalyst Pump Catalyst Pump Details System Parts Systems 152 24M692 SPACER, ball joint Wall or Pole Mount KIT Wall or Pole Mount KIT Wall or Pole Mount KIT Carts Quantity System Parts Wall or Pole Mount Kit, 16N918 Part Description Qty Boom, 16N761 Air Panel Slave Pump Linkage, 16P125 Resin Pumplines Part Description 131 171 Gun Connecting KitAir Motor and Pump for Resin Pumpline Coupling Collars Mesh Pack Resin Filter24F620 Resin Supply Hose 16M736 3A2012J Catalyst Slave Pumps 922 930 940 Installation Tools not shown Catalyst Pumps Catalyst Reservoir 16P425 Cart not included in kit, shown for reference only Hose Bundles Quantity 16N0169, 16N017, 16N018, and 16N019 Kits Accessory Parts Heater Kits16N014 and 16N015 Kits Nipple Solvent Pressure Pot Kits Asme Pressure Pots, 2-gallon 16M893 and 5-gallon 16M894 Asme and CE-Approved Pressure Pots, 16M874 and 16M875 Tube Solvent Diaphragm Pumps Gallon 16M560 and 5-gallon 16M561 DataTrak Upgrade Kit 16M881 Carts for 55 Gallon Barrel, 16M896 Roving Box Bracket 16M961 Chop Hose Extension HosesGel Hose For external gel Top View DimensionsCart and Boom Cart Only Wall/Pole Mount Technical Data Pumpline Wall Mounting Bracket Dimensions Pumpline Technical Data 3A2012J Graco Standard Warranty Graco Information