Solvent Flush Systems | Graco ti18524d, ti18496b, ti18526c manual

Solvent Flush Systems

Solvent Flush Diaphragm Pump

The solvent flush diaphragm pump provides solvent to the gun to clear out mixed fluid and prevent it from cur- ing in the gun. See the diaphragm pump manual listed on page 3 for detailed component identification.

	3/4 npt(f) Fluid
1/4 npt(f)	Outlet
Air Inlet

3/4 npt(f)

Fluid Outlet

3/4 npt(f) Fluid Outlet

ti9078a1

FIG. 4: Solvent Pump Components

Solvent Flush ASME Pressure Pot

The pressure pot works by using the incoming air pres- sure to expel the solvent in the pot out of the fluid outlet. Verify supply tube is installed on fluid outlet port.

Air Inlet

Fill Cap

Fluid Outlet

ti18530a

Component Identification

Solvent Flush ASME and CE-Approved Pressure Pot

The pressure pot works by using the incoming air pres- sure to expel the solvent in the pot out of the fluid outlet. See the ASME and CE-approved Pressure Pot manual listed on page 3 for detailed component identification.

Air Inlet

Fill Cap

Fluid Outlet

ti18531a

3A2012J

15

Image 15

Graco ti18524d Solvent Flush Systems, Solvent Flush Diaphragm Pump, Solvent Flush Asme and CE-Approved Pressure Pot

Contents

FRP Proportioner Important Safety Instructions Contents Related Manuals Agency ApprovalsManual Description Length Ratio ModelsNo Cart Cart, Mast, and Boom Hose Accessories Skin Injection Hazard Toxic Fluid or Fumes Hazard 3A2012J Keep Resin and Catalyst Components Separate Important Two-Component Material InformationMaterial Self-ignition Changing Materials Typical Applications Overview Key Component Identification Air Control Panel Pressurized fluid outlet on filter R connect fluid Air Motor and Resin Displacement PumpPressure relief/recirculation valve P relieves pres Pressure relief/recirculation fluid outlet P1 place Catalyst Pump Components Catalyst Pump Solvent Flush Systems Solvent Flush Diaphragm PumpSolvent Flush Asme and CE-Approved Pressure Pot System Mounting Wall Mount Systems Only SetupBefore Installation Location Requirements For systems bolting directly to wall not using a pole For cart and boom systems only, install legs System Assembly Spring Chain Roving Guides Deflector Plates Grounding Ground Wire Air Connections Connect Fluid and Air Lines Catalyst Pump Pressure Relief Valve Gun Connections Flush Before First UseFill Supply Tanks Solvent Flush Connections if applicable Boom Operation Pressure Relief Procedure and ShutdownOperation Trigger Lock Operation For internal mix proportioners only, check solvent line Startup Prime Follow Pressure Relief Procedure and Shut- down on Operation 3A2012J Flush External mix systems 30-40 psi 0.21-0.28 MPa, 2.1-2.8 bar Spray Follow Pressure Relief Procedure and Shutdown on AAC Air Adjustment Run Mode Setup ModeDataTrak Operation Operation Solenoid Release Button Runaway Monitor Display DiagnosticsPrime/Flush Counter/Totalizer Diagnostic Codes Symbol Code Name Diagnosis Cause Disconnect DataTrak Replace DataTrak Battery or Fuse Maintenance ComponentsTask Schedule Inspect pump wetcup Daily Resin Pump Troubleshooting Spray pattern Mendations Fluid is too thin or too thick Disconnect the Displacement Pump RepairGeneral Information Align cylinder and adapter plate Reconnect the Displacement Pump Reconnect the Air Motor Disconnect the Air Motor Ti18456c Replace Pumpline Repair Throat and Piston Seals Repair Catalyst PumpRemove Catalyst Pump from System Disassemble Catalyst Pump Assemble Catalyst Pump Repair Foot Valve Catalyst Pump Details Systems System Parts 152 24M692 SPACER, ball joint Wall or Pole Mount KIT Wall or Pole Mount KIT Wall or Pole Mount KIT Quantity Carts System Parts Part Description Qty Wall or Pole Mount Kit, 16N918 Boom, 16N761 Air Panel Slave Pump Linkage, 16P125 Part Description 131 171 Resin Pumplines Coupling Collars Connecting KitAir Motor and Pump for Resin Pumpline Gun Resin Filter 24F620Mesh Pack 16M736 Resin Supply Hose 3A2012J 922 930 940 Catalyst Slave Pumps Catalyst Pumps Installation Tools not shown 16P425 Catalyst Reservoir Cart not included in kit, shown for reference only Hose Bundles Quantity Accessory Parts Heater Kits 16N014 and 16N015 Kits16N0169, 16N017, 16N018, and 16N019 Kits Nipple Asme Pressure Pots, 2-gallon 16M893 and 5-gallon 16M894 Solvent Pressure Pot Kits Tube Asme and CE-Approved Pressure Pots, 16M874 and 16M875 Gallon 16M560 and 5-gallon 16M561 Solvent Diaphragm Pumps 16M881 DataTrak Upgrade Kit Carts for 55 Gallon Barrel, 16M896 16M961 Roving Box Bracket For external gel Extension HosesGel Hose Chop Hose Dimensions Cart and BoomTop View Wall/Pole Mount Cart Only Pumpline Wall Mounting Bracket Dimensions Technical Data Pumpline Technical Data 3A2012J Graco Information Graco Standard Warranty