Manuals / Graco / Marine Equipment / Outboard Motor

Graco ti18526c, ti18524d, ti18496b Technical Data, Pumpline Wall Mounting Bracket Dimensions

Models: ti18526c ti18524d ti18496b

1 86

Download 86 pages 48.04 Kb

Page 83

Image 83

Technical Data

Pumpline Wall Mounting Bracket Dimensions

The pumpline bolts directly to this mounting plate.

WLD

Four 0.60 in. (15 mm) mounting holes

3.52in.

(89.4 mm)

10.1in. (257 mm)

Technical Data

System Technical Data

Maximum fluid working pressure	13:1 Systems: 1300 psi (9 MPa, 90 bar)
	17:1 Systems: 1700 psi (11.9 MPa, 119 bar)
Maximum air inlet pressure	100 psi (0.7 MPa, 7.0 bar)
Maximum air inlet pressure to ASME solvent pressure pots . . .	100 psi (0.7 MPa, 7.0 bar)
Typical flow rate of pattern guns	Refer to RS Gun manual. See Related Manuals, page 3.
Maximum fluid temperature (Models with RS Gun)	100°F (38°C)*
Maximum fluid temperature (Models without RS Gun)	160°F (71°C)*
A component (catalyst) inlet size	3/8 in. tube
B component (resin) inlet size	1 5/16-12 UN-2A male
Wetted parts	Stainless steel, carbide, UHMWPE, PTFE, and acetal.
Resin wetted parts	See Pumpline Technical Data, page 84
Catalyst wetted parts	See Catalyst Pump Technical Data, page 84

*Maximum fluid temperature rating determined by lowest rated component in system.

3A2012J

83

Image 83

Graco ti18526c, ti18524d, ti18496b specifications Technical Data, Pumpline Wall Mounting Bracket Dimensions

Contents

FRP Proportioner Important Safety Instructions Contents Manual Description Related ManualsAgency Approvals Length Ratio ModelsNo Cart Cart, Mast, and Boom Hose Accessories Skin Injection Hazard Toxic Fluid or Fumes Hazard 3A2012J Keep Resin and Catalyst Components Separate Important Two-Component Material InformationMaterial Self-ignition Changing Materials Typical Applications Overview Key Component Identification Air Control Panel Pressurized fluid outlet on filter R connect fluid Air Motor and Resin Displacement PumpPressure relief/recirculation valve P relieves pres Pressure relief/recirculation fluid outlet P1 place Catalyst Pump Components Catalyst Pump Solvent Flush Asme and CE-Approved Pressure Pot Solvent Flush SystemsSolvent Flush Diaphragm Pump System Mounting Wall Mount Systems Only SetupBefore Installation Location Requirements For systems bolting directly to wall not using a pole For cart and boom systems only, install legs System Assembly Spring Chain Roving Guides Deflector Plates Grounding Ground Wire Air Connections Connect Fluid and Air Lines Catalyst Pump Pressure Relief Valve Gun Connections Flush Before First UseFill Supply Tanks Solvent Flush Connections if applicable Boom Operation Pressure Relief Procedure and ShutdownOperation Trigger Lock Operation For internal mix proportioners only, check solvent line Startup Prime Follow Pressure Relief Procedure and Shut- down on Operation 3A2012J Flush External mix systems 30-40 psi 0.21-0.28 MPa, 2.1-2.8 bar Spray Follow Pressure Relief Procedure and Shutdown on AAC Air Adjustment DataTrak Operation Run ModeSetup Mode Operation Solenoid Release Button Runaway Monitor Display DiagnosticsPrime/Flush Counter/Totalizer Diagnostic Codes Symbol Code Name Diagnosis Cause Disconnect DataTrak Replace DataTrak Battery or Fuse Task Schedule Inspect pump wetcup Daily MaintenanceComponents Resin Pump Troubleshooting Spray pattern Mendations Fluid is too thin or too thick General Information Disconnect the Displacement PumpRepair Align cylinder and adapter plate Reconnect the Displacement Pump Reconnect the Air Motor Disconnect the Air Motor Ti18456c Replace Pumpline Repair Throat and Piston Seals Repair Catalyst PumpRemove Catalyst Pump from System Disassemble Catalyst Pump Assemble Catalyst Pump Repair Foot Valve Catalyst Pump Details Systems System Parts 152 24M692 SPACER, ball joint Wall or Pole Mount KIT Wall or Pole Mount KIT Wall or Pole Mount KIT Quantity Carts System Parts Part Description Qty Wall or Pole Mount Kit, 16N918 Boom, 16N761 Air Panel Slave Pump Linkage, 16P125 Part Description 131 171 Resin Pumplines Coupling Collars Connecting KitAir Motor and Pump for Resin Pumpline Gun Mesh Pack Resin Filter24F620 16M736 Resin Supply Hose 3A2012J 922 930 940 Catalyst Slave Pumps Catalyst Pumps Installation Tools not shown 16P425 Catalyst Reservoir Cart not included in kit, shown for reference only Hose Bundles Quantity 16N0169, 16N017, 16N018, and 16N019 Kits Accessory Parts Heater Kits16N014 and 16N015 Kits Nipple Asme Pressure Pots, 2-gallon 16M893 and 5-gallon 16M894 Solvent Pressure Pot Kits Tube Asme and CE-Approved Pressure Pots, 16M874 and 16M875 Gallon 16M560 and 5-gallon 16M561 Solvent Diaphragm Pumps 16M881 DataTrak Upgrade Kit Carts for 55 Gallon Barrel, 16M896 16M961 Roving Box Bracket For external gel Extension HosesGel Hose Chop Hose Top View DimensionsCart and Boom Wall/Pole Mount Cart Only Pumpline Wall Mounting Bracket Dimensions Technical Data Pumpline Technical Data 3A2012J Graco Information Graco Standard Warranty