DataTrak Operation, Run Mode, Setup Mode | Graco ti18524d, ti18496b

DataTrak Operation

For DataTrak installation instructions, see NXT Air motor for FRP manual.

Operation

NOTICE

To prevent damage to the soft key buttons, do not press the buttons with sharp objects such as pens, plastic cards, or fingernails.

Controls and Indicators

NOTE: See FIG. 31. The display (Y) will turn off after 1 minute of inactivity in Run mode or 3 minutes in Setup mode. Press any key to wake up the display. DataTrak will continue to count cycles when display is off.

Run Mode

GT BT

CF; See Details at right.

RK

PF

			CF
				TI8622b
			Setup Mode
			RT	UT
			CC
			*CB	DT
			*CB	ST
	CD	TI11883a		ST
	CD	TI11883a	RK	PF
			RK	PF
			CA	TI8623b

FIG. 31. DataTrak Controls and Indicators

Key:

CA Runaway Limit, in cycles per minute (user settable; 00=OFF)

CB * Lower Displacement (user settable)

CCFlow Rate Units (user settable to /min, gpm [US], gpm [Imperial], oz/min [US], oz/min [Imperial], l/min, or

cc/min)

CD LED (fault indicator when lit)

CE Diagnostic Reference Card (see Table 1, page 37) CF Display

PF Prime/Flush Key (Enables Prime/Flush mode. While in Prime/Flush mode, runaway protection is disabled and the batch totalizer (BT) will not count.)

RK Reset Key (Resets faults. Press and hold for 3 seconds to clear the batch totalizer.)

CF Cycle/Flow Rate

BT Batch Totalizer

GT Grand Totalizer

RT Runaway Toggle (enable/disable)

UT E1 Error Option (enable/disable)

DT E2 Error Option (enable/disable)

ST E5 Error Option (enable/disable)

3A2012J

33

Image 33

Graco ti18524d, ti18496b, ti18526c specifications DataTrak Operation, Run Mode, Setup Mode

Contents

FRP Proportioner Important Safety Instructions Contents Related Manuals Agency ApprovalsManual Description No Cart Cart, Mast, and Boom ModelsHose Length Ratio Accessories Skin Injection Hazard Toxic Fluid or Fumes Hazard 3A2012J Material Self-ignition Important Two-Component Material InformationChanging Materials Keep Resin and Catalyst Components Separate Typical Applications Overview Key Component Identification Air Control Panel Pressure relief/recirculation valve P relieves pres Air Motor and Resin Displacement PumpPressure relief/recirculation fluid outlet P1 place Pressurized fluid outlet on filter R connect fluid Catalyst Pump Components Catalyst Pump Solvent Flush Systems Solvent Flush Diaphragm PumpSolvent Flush Asme and CE-Approved Pressure Pot Before Installation SetupLocation Requirements System Mounting Wall Mount Systems Only For systems bolting directly to wall not using a pole For cart and boom systems only, install legs System Assembly Spring Chain Roving Guides Deflector Plates Grounding Ground Wire Air Connections Connect Fluid and Air Lines Catalyst Pump Pressure Relief Valve Fill Supply Tanks Flush Before First UseSolvent Flush Connections if applicable Gun Connections Operation Pressure Relief Procedure and ShutdownTrigger Lock Boom Operation Operation For internal mix proportioners only, check solvent line Startup Prime Follow Pressure Relief Procedure and Shut- down on Operation 3A2012J Flush External mix systems 30-40 psi 0.21-0.28 MPa, 2.1-2.8 bar Spray Follow Pressure Relief Procedure and Shutdown on AAC Air Adjustment Run Mode Setup ModeDataTrak Operation Operation Solenoid Release Button Runaway Monitor Prime/Flush DiagnosticsCounter/Totalizer Display Diagnostic Codes Symbol Code Name Diagnosis Cause Disconnect DataTrak Replace DataTrak Battery or Fuse Maintenance ComponentsTask Schedule Inspect pump wetcup Daily Resin Pump Troubleshooting Spray pattern Mendations Fluid is too thin or too thick Disconnect the Displacement Pump RepairGeneral Information Align cylinder and adapter plate Reconnect the Displacement Pump Reconnect the Air Motor Disconnect the Air Motor Ti18456c Replace Pumpline Remove Catalyst Pump from System Repair Catalyst PumpDisassemble Catalyst Pump Repair Throat and Piston Seals Assemble Catalyst Pump Repair Foot Valve Catalyst Pump Details Systems System Parts 152 24M692 SPACER, ball joint Wall or Pole Mount KIT Wall or Pole Mount KIT Wall or Pole Mount KIT Quantity Carts System Parts Part Description Qty Wall or Pole Mount Kit, 16N918 Boom, 16N761 Air Panel Slave Pump Linkage, 16P125 Part Description 131 171 Resin Pumplines Air Motor and Pump for Resin Pumpline Connecting KitGun Coupling Collars Resin Filter 24F620Mesh Pack 16M736 Resin Supply Hose 3A2012J 922 930 940 Catalyst Slave Pumps Catalyst Pumps Installation Tools not shown 16P425 Catalyst Reservoir Cart not included in kit, shown for reference only Hose Bundles Quantity Accessory Parts Heater Kits 16N014 and 16N015 Kits16N0169, 16N017, 16N018, and 16N019 Kits Nipple Asme Pressure Pots, 2-gallon 16M893 and 5-gallon 16M894 Solvent Pressure Pot Kits Tube Asme and CE-Approved Pressure Pots, 16M874 and 16M875 Gallon 16M560 and 5-gallon 16M561 Solvent Diaphragm Pumps 16M881 DataTrak Upgrade Kit Carts for 55 Gallon Barrel, 16M896 16M961 Roving Box Bracket Gel Hose Extension HosesChop Hose For external gel Dimensions Cart and BoomTop View Wall/Pole Mount Cart Only Pumpline Wall Mounting Bracket Dimensions Technical Data Pumpline Technical Data 3A2012J Graco Information Graco Standard Warranty