Grounding, Ground Wire | Graco ti18526c, ti18524d, ti18496b manual

Setup

Grounding

The equipment must be grounded to reduce the risk of static sparking and electric shock. Electric or static sparking can cause fumes to ignite or explode. Improper grounding can cause electric shock. Grounding provides an escape wire for the electric current

FRP Proportioner Grounding

NOTE: All proportioners come with one grounding clamp to ground the proportioner to a true earth ground. All accessories for internal mix systems come with a second grounding clamp to ground the solvent flush system to the cart.

1.Verify that the ground screw is attached and tight- ened securely to the air motor. Connect the other end of the ground wire to a true earth ground.

General Grounding Guidelines

Pump: use ground wire and clamp (supplied). Connect ground clamp to a true earth ground.

Air and fluid hoses: use only electrically conductive hoses.

Spray gun: ground through connection to a properly grounded fluid hose and pump.

Fluid supply container: follow local code.

Object being sprayed: follow local code.

Solvent pails used when flushing: follow local code. Use only conductive metal pails, placed on a grounded surface. Do not place the pail on a nonconductive sur- face, such as paper or cardboard, which interrupts grounding continuity.

Ground screw

Grounding wire

ti18454a

FIG. 5: Ground Wire

2.For internal mix systems only, ground the solvent flush system.

a.For solvent flush diaphragm pumps only, con- nect one end of the second grounding clamp to the solvent pump grounding strip. See the dia- phragm pump manual listed on page 3 for grounding details.

b.Connect the other end of the grounding clamp to the cart.

3.Use an ohmmeter to verify all components are grounded to the earth ground.

4.If wall power is used to power the heater, ground electrical connection according to local codes.

5.For cart proportioners: Connect the other end of the

second supplied grounding clamp to the cart.

For wall proportioners: Connect the other end of the second supplied grounding clamp to a true earth ground.

20

3A2012J

Image 20

Graco ti18526c, ti18524d, ti18496b specifications Grounding, Ground Wire

Contents

Important Safety Instructions FRP Proportioner Contents Manual Description Related ManualsAgency Approvals Models No Cart Cart, Mast, and BoomHose Length Ratio Accessories Skin Injection Hazard Toxic Fluid or Fumes Hazard 3A2012J Important Two-Component Material Information Material Self-ignitionChanging Materials Keep Resin and Catalyst Components Separate Overview Typical Applications Component Identification Key Air Control Panel Air Motor and Resin Displacement Pump Pressure relief/recirculation valve P relieves presPressure relief/recirculation fluid outlet P1 place Pressurized fluid outlet on filter R connect fluid Catalyst Pump Catalyst Pump Components Solvent Flush Asme and CE-Approved Pressure Pot Solvent Flush SystemsSolvent Flush Diaphragm Pump Setup Before InstallationLocation Requirements System Mounting Wall Mount Systems Only For systems bolting directly to wall not using a pole System Assembly For cart and boom systems only, install legs Spring Chain Roving Guides Deflector Plates Ground Wire Grounding Connect Fluid and Air Lines Air Connections Catalyst Pump Pressure Relief Valve Flush Before First Use Fill Supply TanksSolvent Flush Connections if applicable Gun Connections Pressure Relief Procedure and Shutdown OperationTrigger Lock Boom Operation Operation Startup For internal mix proportioners only, check solvent line Follow Pressure Relief Procedure and Shut- down on Prime Operation 3A2012J Flush Spray External mix systems 30-40 psi 0.21-0.28 MPa, 2.1-2.8 bar AAC Air Adjustment Follow Pressure Relief Procedure and Shutdown on DataTrak Operation Run ModeSetup Mode Operation Runaway Monitor Solenoid Release Button Diagnostics Prime/FlushCounter/Totalizer Display Diagnostic Codes Symbol Code Name Diagnosis Cause Replace DataTrak Battery or Fuse Disconnect DataTrak Task Schedule Inspect pump wetcup Daily MaintenanceComponents Troubleshooting Resin Pump Spray pattern Mendations Fluid is too thin or too thick General Information Disconnect the Displacement PumpRepair Reconnect the Displacement Pump Align cylinder and adapter plate Disconnect the Air Motor Reconnect the Air Motor Ti18456c Replace Pumpline Repair Catalyst Pump Remove Catalyst Pump from SystemDisassemble Catalyst Pump Repair Throat and Piston Seals Repair Foot Valve Assemble Catalyst Pump Catalyst Pump Details System Parts Systems 152 24M692 SPACER, ball joint Wall or Pole Mount KIT Wall or Pole Mount KIT Wall or Pole Mount KIT Carts Quantity System Parts Wall or Pole Mount Kit, 16N918 Part Description Qty Boom, 16N761 Air Panel Slave Pump Linkage, 16P125 Resin Pumplines Part Description 131 171 Connecting Kit Air Motor and Pump for Resin PumplineGun Coupling Collars Mesh Pack Resin Filter24F620 Resin Supply Hose 16M736 3A2012J Catalyst Slave Pumps 922 930 940 Installation Tools not shown Catalyst Pumps Catalyst Reservoir 16P425 Cart not included in kit, shown for reference only Hose Bundles Quantity 16N0169, 16N017, 16N018, and 16N019 Kits Accessory Parts Heater Kits16N014 and 16N015 Kits Nipple Solvent Pressure Pot Kits Asme Pressure Pots, 2-gallon 16M893 and 5-gallon 16M894 Asme and CE-Approved Pressure Pots, 16M874 and 16M875 Tube Solvent Diaphragm Pumps Gallon 16M560 and 5-gallon 16M561 DataTrak Upgrade Kit 16M881 Carts for 55 Gallon Barrel, 16M896 Roving Box Bracket 16M961 Extension Hoses Gel HoseChop Hose For external gel Top View DimensionsCart and Boom Cart Only Wall/Pole Mount Technical Data Pumpline Wall Mounting Bracket Dimensions Pumpline Technical Data 3A2012J Graco Standard Warranty Graco Information