Tube | Graco ti18524d, ti18496b, ti18526c manual

ASME and CE-Approved Pressure Pots, 16M874 and 16M875

System Parts

1Apply pipe sealant.

2Clamp ground cable (1423) to handle on tank (1401). Ground cable not shown.

3Must be installed on the outlet side. The outlet is the port without the cross hole.

1 1411

1 1406

1 1410

1 1408

1 1412

1401

1404

1401

1414

1401

1403 1408 1

1402

1409 1

1406 1

1405 3

Ref	Part	Description	Qty
1401	236086	TANK, pressure assy, 2 gal.	1
		(assembly 16M874 only)
	236087	TANK, pressure assy, 5 gal.	1
		(assembly 16M875 only)
1402	165053	PACKING, o-ring	1
1403	188880	PLUG, lid	1
1404	188784	NUT, jam, hex	1
1405	171976	TUBE	1
		(assembly 16M875 only)
	185531	TUBE, siphon (assembly	1
		16M874 only)
1406	---	BUSHING, hex, 3/8npt x 1/4npt,	2
		male/female
1407	111763	FITTING, elbow, 1/4 npt	1
1408	18470-05	VALVE, ball, 2-way, 1/4nptf	2
1409	---	FITTING, nipple, reducing	1
1410	108673	TEE, street	1
1411	103347	VALVE, safety, 100 psi	1
1412	---	FITTING, connector, male,	1
		3/8 npt
1413	210575	CAP, filler (assembly 16M875	1
		only, not shown)
1414	176347	LABEL, identification	1

Ref	Part	Description	Qty
1415	---	LABEL, designation	1
1416▲175078		LABEL, warning	1
1421	308370	MANUAL	1
1423	17440-00	CLAMP, grounding	1
1424	171988	O-RING (for filler cap,	1
		item 1413, not shown)

▲Replacement Danger and Warning labels, tags and cards are available at no cost.

3A2012J

75

Image 75

Graco ti18524d, ti18496b, ti18526c specifications Asme and CE-Approved Pressure Pots, 16M874 and 16M875, Tube

Contents

FRP Proportioner Important Safety Instructions Contents Related Manuals Agency ApprovalsManual Description Length Ratio ModelsNo Cart Cart, Mast, and Boom Hose Accessories Skin Injection Hazard Toxic Fluid or Fumes Hazard 3A2012J Keep Resin and Catalyst Components Separate Important Two-Component Material InformationMaterial Self-ignition Changing Materials Typical Applications Overview Key Component Identification Air Control Panel Pressurized fluid outlet on filter R connect fluid Air Motor and Resin Displacement PumpPressure relief/recirculation valve P relieves pres Pressure relief/recirculation fluid outlet P1 place Catalyst Pump Components Catalyst Pump Solvent Flush Systems Solvent Flush Diaphragm PumpSolvent Flush Asme and CE-Approved Pressure Pot System Mounting Wall Mount Systems Only SetupBefore Installation Location Requirements For systems bolting directly to wall not using a pole For cart and boom systems only, install legs System Assembly Spring Chain Roving Guides Deflector Plates Grounding Ground Wire Air Connections Connect Fluid and Air Lines Catalyst Pump Pressure Relief Valve Gun Connections Flush Before First UseFill Supply Tanks Solvent Flush Connections if applicable Boom Operation Pressure Relief Procedure and ShutdownOperation Trigger Lock Operation For internal mix proportioners only, check solvent line Startup Prime Follow Pressure Relief Procedure and Shut- down on Operation 3A2012J Flush External mix systems 30-40 psi 0.21-0.28 MPa, 2.1-2.8 bar Spray Follow Pressure Relief Procedure and Shutdown on AAC Air Adjustment Run Mode Setup ModeDataTrak Operation Operation Solenoid Release Button Runaway Monitor Display DiagnosticsPrime/Flush Counter/Totalizer Diagnostic Codes Symbol Code Name Diagnosis Cause Disconnect DataTrak Replace DataTrak Battery or Fuse Maintenance ComponentsTask Schedule Inspect pump wetcup Daily Resin Pump Troubleshooting Spray pattern Mendations Fluid is too thin or too thick Disconnect the Displacement Pump RepairGeneral Information Align cylinder and adapter plate Reconnect the Displacement Pump Reconnect the Air Motor Disconnect the Air Motor Ti18456c Replace Pumpline Repair Throat and Piston Seals Repair Catalyst PumpRemove Catalyst Pump from System Disassemble Catalyst Pump Assemble Catalyst Pump Repair Foot Valve Catalyst Pump Details Systems System Parts 152 24M692 SPACER, ball joint Wall or Pole Mount KIT Wall or Pole Mount KIT Wall or Pole Mount KIT Quantity Carts System Parts Part Description Qty Wall or Pole Mount Kit, 16N918 Boom, 16N761 Air Panel Slave Pump Linkage, 16P125 Part Description 131 171 Resin Pumplines Coupling Collars Connecting KitAir Motor and Pump for Resin Pumpline Gun Resin Filter 24F620Mesh Pack 16M736 Resin Supply Hose 3A2012J 922 930 940 Catalyst Slave Pumps Catalyst Pumps Installation Tools not shown 16P425 Catalyst Reservoir Cart not included in kit, shown for reference only Hose Bundles Quantity Accessory Parts Heater Kits 16N014 and 16N015 Kits16N0169, 16N017, 16N018, and 16N019 Kits Nipple Asme Pressure Pots, 2-gallon 16M893 and 5-gallon 16M894 Solvent Pressure Pot Kits Tube Asme and CE-Approved Pressure Pots, 16M874 and 16M875 Gallon 16M560 and 5-gallon 16M561 Solvent Diaphragm Pumps 16M881 DataTrak Upgrade Kit Carts for 55 Gallon Barrel, 16M896 16M961 Roving Box Bracket For external gel Extension HosesGel Hose Chop Hose Dimensions Cart and BoomTop View Wall/Pole Mount Cart Only Pumpline Wall Mounting Bracket Dimensions Technical Data Pumpline Technical Data 3A2012J Graco Information Graco Standard Warranty