Manuals / HP / Computer Equipment / Network Card

HP 3162 manual DTE Drop/Insert Interface, Figure D-3. DTE Drop/Insert DSX-1 Cable

Models: 3162

1 199

Download 199 pages 36.77 Kb

Page 143

Pin Assignments

DTE Drop/Insert Interface

The DTE Drop/Insert (DSX-1) interface connector is a DB15-type socket connector (Table D-2). For information about using Relay Contact Sense for external DTE loopback, refer to the DTE LB on Contact configuration option in DTE Interface Configuration Options of Appendix C.

The DTE Drop/Insert (DSX-1) cable (Figure D-3) is typically supplied by a DTE vendor. It is made of shielded twisted-pair wires (22 AWG). The cable connector is a DB15-type plug connector. Be sure to connect the shield ground only at the DSU/CSU end to prevent ground loops.

Table D-2. DTE Drop/Insert (DSX-1 Connector)

Signal	Pin Number

Receiver Tip from DTE	1

Receiver Ring from DTE	9

Transmitter Tip to DTE	3

Transmitter Ring to DTE	11

Relay Contact Sense Return	12

Relay Contact Sense	14

Shield Ground	2,4

Figure D-3. DTE Drop/Insert (DSX-1) Cable

3162-A2-GB20-40

August 2000

D-3

Image 143

HP 3162 manual DTE Drop/Insert Interface, Figure D-3. DTE Drop/Insert DSX-1 Cable

Contents

ACCULINK Document Feedback Warranty, Sales, Service, and Training InformationCopyright E 2000 Paradyne Corporation All rights reserved TrademarksImportant Safety Instructions United States EMI Notice DSU/CSU Facility Interface Codes Description Government Requirements and Equipment Return United StatesCanada Contents Operation Iii Monitoring and TestingConfiguration Options Equipment List Glossary Index Contents Vii About This GuideDocument Purpose and Intended Audience Document SummaryViii Product-Related DocumentsDocument Number Document Title Reference Documents About This Guide Overview FeaturesIntroduction Asynchronous Terminal Interface Support Alarm Message CapabilityTelnet Access DTE Drop/Insert DSX-1 InterfaceDSU/CSU Front Panel Physical DescriptionCOM Port DSU/CSU Rear Panel Connectors Name FunctionApplication Examples InstallationNetwork Services Direct Connection Snmp or Telnet Connection ExamplesConnection through the 10BaseT Port Important InstructionsCabling Example Cabling ExampleProcedure Power-On Self-TestFront Panel LEDs OperationNetwork Interface LEDs Name Color Meaning System LEDs Name Color MeaningBPV DTE Drop/Insert DSX-1 Interface LEDs Name Color MeaningPDV Data Port LEDs Name Color Meaning Area Initiating an Asynchronous Terminal SessionEnding an Asynchronous Terminal Session ScreenRecovering Asynchronous Terminal Operation Menu Organization Main Status Test Configuration ControlConfiguration Edit/Display Screen Function Keys Usage Using Asynchronous Terminal ScreensKeyboard Keys Usage Entering a Password Entering a Password to Gain AccessExample of Display LEDs Screen Displaying LED ConditionsChanging Configuration Options Configuration Load Screen Displaying or Editing Configuration OptionsConfiguration Edit/Display Screen Saving Edit Changes Configuration Save ScreenOperation Configuration Field Setting Customer IdentificationCustomer IdentificationEthernet Port Options Screen Configuring the 10BaseT PortConfiguring the COM Port for Snmp or Telnet Access Communication Port Options Screen Configuring the COM Port for ManagementSetting the IP Address Selecting the Link Layer Protocol Configuring DS0 Channels Example of Channel Allocation Network Channel Allocation Network InterfaceDTE Drop/Insert DSX-1 Interface DTE DSX-1 Channel Allocation DTE to Network DS0 Designations Meaning Displaying DS0 Channel AssignmentsNetChan Assignment DTE toNetwork DTE to Interface Options Screen Configuring DS0 Channels for Robbed Bit SignalingProcedure Clearing DS0 Channel Allocation Establishing Access Security on the COM Port Re-Enter Setting a PasswordPassword Selecting the Timing Source 11. Common Clocking ConfigurationsProviding Backup Capability Configuration Self-Test Results Monitoring and TestingSelf-Test Results Message Description Health and Status Messages 1 Description Device Health and StatusHealth and Status Messages 2 Description Performance Reports BES UASSES Lofc CSSEthernet Statistics Ethernet Port Status Field Description TTL IP Routing TableTTL IP Routing Table Field DescriptionAlarms Snmp Traps Snmp Trap per Interface Trap Meaning Enterprise-Specific Trap Definitions Trap Value EventTroubleshooting 1 Symptom Possible Cause Solutions TroubleshootingMessage OOF at DTE Troubleshooting 2 Symptom Possible Cause SolutionsTest Jacks Test JacksTest Jack Functions Test Jack Name Test CommandsFor Channels Remote Loopback TestsSending a Line Loopback Up or Down For NetworksSending a V.54 or Ansi FT1 Activation/Deactivation Sequence Local Loopback Tests10. Valid Loopback Combinations Starting a Line LoopbackStarting a DTE Loopback Starting a Payload LoopbackStarting a Repeater Loopback Starting a Data Channel Loopback Aborting Loopbacks Starting a Data Terminal LoopbackIn-8 Network Port Test PatternsSending Network Qrss or Network 1-in-8 Test Patterns Network Qrss PortMonitoring Port Qrss or Port 511 Test Patterns Sending Port Qrss or Port 511 Test PatternsMonitoring Network Qrss Test Patterns Aborting a Lamp Test Lamp TestAborting Test Patterns Starting a Lamp Test12. Test Status Messages Description Displaying DSU/CSU Test StatusMonitoring and Testing Asynchronous Terminal Menu Asynchronous Terminal Menu Technical Specifications Approvals Physical DimensionsWeight Port InterfaceConfiguration Options AMI B8ZS Network Interface Configuration OptionsTable C-1. Network Interface Configuration Options 1 D4 ESFNetwork Initiated PLB Enable Enable Disable Table C-1. Network Interface Configuration Options 2Ansi Performance Report Messages Disable Enable Disable Network Initiated LLB Enable Enable DisableTable C-2. DTE Interface Configuration Options 1 DTE Interface Configuration OptionsValue Meaning Table C-2. DTE Interface Configuration Options 2RBS RBS RBS RBS RBS RBS RBS RBS RBS Port Base Rate Nx64 Nx64 Nx56 Sync Data Port Configuration OptionsTable C-3. Sync Data Port Configuration Options 1 Port Type E530 Factory 1 V.35 Factory RS449Invert Transmit Clock Disable Enable Disable Table C-3. Sync Data Port Configuration Options 2Embedded Data Link Disable Enable Disable EDL Management Link Disable Enable DisableAction on Network Yellow Alarm Halt None Halt Table C-3. Sync Data Port Configuration Options 3Far-End Performance Statistics Disable Disable Maintain Table C-3. Sync Data Port Configuration Options 4Table C-3. Sync Data Port Configuration Options 5 DTE01 DTE02 DTE03 DTE04 DTE05 DTE06 DTE07 DTE08 DTE24 Cross Connect Configuration OptionsDTE-to-Network Assignment Options Table C-4. DTE-to-Network Assignment OptionsTable C-5. Sync Data Port Assignment Options 1 Sync Data Port Assignment OptionsTable C-5. Sync Data Port Assignment Options 2 D01 D02 D03 D04 D05 D06 D07 D08 D24 Table C-5. Sync Data Port Assignment Options 3Table C-6. General Configuration Options 1 General Configuration OptionsExternal Clock Rate KHz 1544 2048 1544 Table C-6. General Configuration Options 2Table C-7. Communication Port Configuration Options 1 User Interface Configuration OptionsCommunication Port Configuration Options Table C-7. Communication Port Configuration Options 2 Table C-8. External Device Configuration Options 1 External Device Configuration OptionsTable C-7. Communication Port Configuration Options 3 Escape Sequence Text Field Table C-8. External Device Configuration Options 2Connect Prefix Text Field Connect Indication String Text FieldDisconnect String Text Field Table C-8. External Device Configuration Options 3Escape Sequence Delay sec None None 0.2 0.4 0.6 0.8 Telnet Session Disable Enable Disable Telnet Sessions Configuration OptionsTable C-9. Telnet Sessions Configuration Options Table C-10. Ethernet Port Configuration Options Ethernet 10BaseT Port Configuration OptionsAlarm & Trap Dial-Out Disable Enable Disable Alarm and Trap Configuration OptionsTable C-11. Alarm and Trap Configuration Options 1 Ascii Alarm Messages Disable Disable Com PortAlternate Dial-Out Directory None None 1 2 3 4 Table C-11. Alarm and Trap Configuration Options 2Call Retry Disable Enable Disable Dial Out Delay Time min 3 4 5 6 7 8 9Node IP Address Text Field Management and Communication Configuration OptionsCommunication Protocol Configuration Options Table C-12. Communication Protocol Configuration Options 1PPP Slip Table C-12. Communication Protocol Configuration Options 2Table C-13. General Snmp Management Configuration Options General Snmp Management Configuration OptionsTable C-14. Snmp NMS Security Configuration Options Snmp NMS Security Configuration OptionsNumber of Trap Managers 1 1 2 3 4 5 Snmp Traps Configuration OptionsTable C-15. Snmp Traps Configuration Options 1 Snmp Traps Disable Enable DisableLink Traps Both Disable Up Down Both Table C-15. Snmp Traps Configuration Options 2General Traps Both Disable Warm AuthFail Both Enterprise Specific Traps Enable Enable DisableLink Trap Interfaces All Network DTE T1s Ports All Table C-15. Snmp Traps Configuration Options 3DTE Interface Options Configuration WorksheetsNetwork Interface Options Sync Data Port Options Port Sync Data Port Options Port Network Interface Network Channel Allocation DTE Drop/Insert DSX-1 Interface DTE DSX-1 Channel Allocation DTE Signaling Assign N1 Voice RBS or Data Acami Sync Data Port OptionsChannel User Interface External Device Options Disable , DTRGeneral Options User Interface Communication PortManagement and Communication Communication Protocol Options Alarm and Trap Configuration OptionsUser Interface Telnet Sessions Options User Interface Ethernet Port OptionsSnmp Traps Options Management and CommunicationSnmp NMS Security Options T1 Network Interface Table D-1. T1 Network Interface Connector Signal Pin NumberPin Assignments Figure D-1. T1 Line Interface Cable, RJ48C-to-RJ48C Figure D-3. DTE Drop/Insert DSX-1 Cable DTE Drop/Insert InterfaceUse Pin # 10BaseT ConnectorCOM Port Interface Table D-3. COM Port Connector Signal Direction Pin NumberFigure D-4. COM Port-to-PC Cable Pin P2 Serial Crossover CablePin EIA-530-A Port Interface Connector Figure D-7. EIA-530-A-to-RS-449 Adapter EIA-530-A-to-RS-449 AdapterPin Assignments Figure D-8. EIA-530-A-to-V.35 Adapter EIA-530-A-to-V.35 AdapterPin Assignments Direction Pin Number EIA-530-A-to-X.21 AdapterExternal Clock Interface Table D-8. External Clock Connector Signal Pin NumberGroup Snmp MIB ObjectsMIB II RFC System Group, MIB System Group sysLocation Object system System Group sysServices Object systemInterface Group, MIB System Group sysName Object systemInterface Group ifDescr Object ifEntry Interface Group ifIndex Object ifEntryInterface Group ifSpeed Object ifEntry Interface Group ifAdminStatus Object ifEntryInterface Group ifType Object ifEntry Interface Group ifMtu Object ifEntryInterface Group ifLastChange Object ifEntry Interface Group ifOperStatus Object ifEntryInterface Group Input Counters objects ifEntry 10 to ifEntry IP Group, MIBIP Group ipAdEntIfIndex Object ipAddrEntry IP Group ipForwarding Object ipIP Group ipAddrTable Object ip IP Group ipAdEntAddr Object ipAddrEntryIP Group ipRouteIfIndex Object ipRouteEntry IP Group ipRouteDest Object ipRouteEntryUDP Group, MIB Icmp Group, MIBTCP Group, MIB Snmp Group, MIB DS1/E1 MIB RFCTransmission Group, MIB Near End Group dsx1LineCoding Object dsx1ConfigEntry Near End Group dsx1TimeElapsed Object dsx1ConfigEntryNear End Group dsx1ValidIntervals Object dsx1ConfigEntry Near End Group dsx1LineType Object dsx1ConfigEntryNear End Group dsx1LoopbackConfig Object dsx1ConfigEntry Near End Group dsx1SendCode Object dsx1ConfigEntryNear End Group dsx1CircuitIdentifier Object dsx1ConfigEntry Near End Group dsx1SignalMode Object dsx1ConfigEntry Near End Group dsx1LineStatus Object dsx1ConfigEntryNear End Group dsx1Fdl Object dsx1ConfigEntry Near End Group The DS1 Total Table Objects dsx1TotalEntry Far End Group, DS1/E1 MIBDS1 Fractional Group, DS1/E1 MIB General Port Table rs232PortIndex Object rs232PortEntry RS-232-like MIB RFCGeneral Port Table, RS-232-like MIB Number of Ports rs232Number Object rs232General Port Table rs232PortOutSpeed Object rs232PortEntry General Port Table rs232PortType Object rs232PortEntryGeneral Port Table rs232PortInSpeed Object rs232PortEntry Asynchronous Port Table, RS-232-like MIB Input Signal Table rs232InSigChanges rs232InSigEntry Input Signal Table, RS-232-like MIBInput Signal Table rs232InSigName rs232InSigEntry Input Signal Table rs232InSigState rs232InSigEntryOutput Signal Table rs232OutSigChanges rs232OutSigEntry Output Signal Table, RS-232-like MIBOutput Signal Table rs232OutSigName rs232OutSigEntry Output Signal Table rs232OutSigState rs232OutSigEntryGeneric Interface Test Table, Generic Interface MIB 3162-A2-GB20-40 August Enterprise MIB IP Network Addressing Scenario Network Standalone at the Central SiteFigure F-2. Local Carrier with Remote Standalone Local Carrier with Remote StandaloneFigure F-3. Local Carrier Connected to Remote Carriers Local and Remote Carriers Different SubnetsLocal and Remote Carriers Same Subnet Figure F-5. Multiple COM Ports Connected to Different NMSs Multiple NMSsEquipment List Equipment Feature NumberEquipment List GL-1 GlossaryGL-2 GL-3 GL-4 GL-5 GL-6 GL-7 GL-8 Numbers IndexIndex IN-2IN-3 IN-4 IN-5