Icmp Group, MIB, TCP Group, MIB, UDP Group, MIB | HP 3162 guide

SNMP MIB Objects

IP Group – “ipRouteMetric2” Object (ipRouteEntry 4)

For standalone devices, ipRouteMetric2 is not used and contains –1.

When adding a route to the routing table using SNMP, do not specify a value for ipRouteMetric2.

IP Group – “ipRouteProto” Object (ipRouteEntry 9)

This object is a read-only object and may have the following values in the

DSU/CSU.

Hother(1) – Temporary route added by IP.

Hlocal(2) – Route added or modified as a result of user configuration via the front panel.

Hnetmgmt(3) – Route added or modified by means of an SNMP set.

Hicmp(4) – Route added or modified by Internet Control Management Protocol (ICMP).

Hrip(8) – Route added or modified by Routing Information Protocol (RIP) or similar proprietary protocol.

IP Group – “ipRouteAge” Object (ipRouteEntry 10)

This object is implemented as a read-only object in the DSU/CSU. In the DSU/CSU, it reflects the value of the route’s time-to-live (in seconds). When displays, a value of 999 represents a route that is retained permanently. For temporary routes, the ipRouteAge object decrements over time. All routes added via an SNMP set of the ipRouteTable are considered permanent routes. These routes do not age, but will remain unless deleted via SNMP.

ICMP Group, MIB II

The ICMP Group objects are fully supported by the DSU/CSU.

TCP Group, MIB II

The TCP Group objects are fully supported by the DSU/CSU, with the exception of the tcpConnState object, which will be read-only.

UDP Group, MIB II

The User Datagram Protocol (UDP) Group objects are fully supported by the

DSU/CSU.

E-10

August 2000

3162-A2-GB20-40

Image 164

HP 3162 manual Icmp Group, MIB, TCP Group, MIB, UDP Group, MIB

Contents

ACCULINK Warranty, Sales, Service, and Training Information Copyright E 2000 Paradyne Corporation All rights reservedTrademarks Document Feedback Important Safety Instructions United States EMI Notice Government Requirements and Equipment Return United States DSU/CSU Facility Interface Codes Description Canada Contents Operation Monitoring and Testing Iii Configuration Options Equipment List Glossary Index Contents About This Guide Document Purpose and Intended AudienceDocument Summary Vii Viii Product-Related DocumentsDocument Number Document Title Reference Documents About This Guide Overview FeaturesIntroduction Alarm Message Capability Telnet AccessDTE Drop/Insert DSX-1 Interface Asynchronous Terminal Interface Support Physical Description DSU/CSU Front Panel DSU/CSU Rear Panel Connectors Name Function COM Port Installation Application Examples Network Services Snmp or Telnet Connection Examples Direct Connection Important Instructions Connection through the 10BaseT Port Cabling Example Cabling Example Power-On Self-Test Procedure Operation Front Panel LEDs System LEDs Name Color Meaning Network Interface LEDs Name Color Meaning BPV DTE Drop/Insert DSX-1 Interface LEDs Name Color MeaningPDV Data Port LEDs Name Color Meaning Initiating an Asynchronous Terminal Session Ending an Asynchronous Terminal SessionScreen Area Recovering Asynchronous Terminal Operation Menu Organization Main Status Test Configuration ControlConfiguration Edit/Display Using Asynchronous Terminal Screens Screen Function Keys Usage Keyboard Keys Usage Entering a Password to Gain Access Entering a Password Displaying LED Conditions Example of Display LEDs Screen Changing Configuration Options Displaying or Editing Configuration Options Configuration Load Screen Configuration Edit/Display Screen Configuration Save Screen Saving Edit Changes Operation Configuration Setting Customer Identification CustomerIdentification Field Configuring the 10BaseT Port Ethernet Port Options Screen Configuring the COM Port for Snmp or Telnet Access Configuring the COM Port for Management Communication Port Options Screen Setting the IP Address Selecting the Link Layer Protocol Configuring DS0 Channels Example of Channel Allocation Network Interface Network Channel Allocation DTE Drop/Insert DSX-1 Interface DTE DSX-1 Channel Allocation Displaying DS0 Channel Assignments DTE to Network DS0 Designations Meaning NetChan Assignment DTE toNetwork Configuring DS0 Channels for Robbed Bit Signaling DTE to Interface Options Screen Procedure Clearing DS0 Channel Allocation Establishing Access Security on the COM Port Re-Enter Setting a PasswordPassword 11. Common Clocking Configurations Selecting the Timing Source Providing Backup Capability Configuration Monitoring and Testing Self-Test Results Self-Test Results Message Description Device Health and Status Health and Status Messages 1 Description Health and Status Messages 2 Description Performance Reports BES UASSES CSS Lofc Ethernet Statistics Ethernet Port Status Field Description IP Routing Table TTL IP Routing Table Field Description TTL Alarms Snmp Traps Enterprise-Specific Trap Definitions Trap Value Event Snmp Trap per Interface Trap Meaning Troubleshooting Troubleshooting 1 Symptom Possible Cause Solutions Troubleshooting 2 Symptom Possible Cause Solutions Message OOF at DTE Test Jacks Test Jacks Test Commands Test Jack Functions Test Jack Name Remote Loopback Tests Sending a Line Loopback Up or DownFor Networks For Channels Local Loopback Tests Sending a V.54 or Ansi FT1 Activation/Deactivation Sequence Starting a Line Loopback 10. Valid Loopback Combinations Starting a Payload Loopback Starting a DTE Loopback Starting a Repeater Loopback Starting a Data Channel Loopback Starting a Data Terminal Loopback Aborting Loopbacks Test Patterns Sending Network Qrss or Network 1-in-8 Test PatternsNetwork Qrss Port In-8 Network Port Monitoring Port Qrss or Port 511 Test Patterns Sending Port Qrss or Port 511 Test PatternsMonitoring Network Qrss Test Patterns Lamp Test Aborting Test PatternsStarting a Lamp Test Aborting a Lamp Test Displaying DSU/CSU Test Status 12. Test Status Messages Description Monitoring and Testing Asynchronous Terminal Menu Asynchronous Terminal Menu Technical Specifications Physical Dimensions WeightPort Interface Approvals Configuration Options Network Interface Configuration Options Table C-1. Network Interface Configuration Options 1D4 ESF AMI B8ZS Table C-1. Network Interface Configuration Options 2 Ansi Performance Report Messages Disable Enable DisableNetwork Initiated LLB Enable Enable Disable Network Initiated PLB Enable Enable Disable DTE Interface Configuration Options Table C-2. DTE Interface Configuration Options 1 Value Meaning Table C-2. DTE Interface Configuration Options 2RBS RBS RBS RBS RBS RBS RBS RBS RBS Sync Data Port Configuration Options Table C-3. Sync Data Port Configuration Options 1Port Type E530 Factory 1 V.35 Factory RS449 Port Base Rate Nx64 Nx64 Nx56 Table C-3. Sync Data Port Configuration Options 2 Embedded Data Link Disable Enable DisableEDL Management Link Disable Enable Disable Invert Transmit Clock Disable Enable Disable Table C-3. Sync Data Port Configuration Options 3 Action on Network Yellow Alarm Halt None Halt Table C-3. Sync Data Port Configuration Options 4 Far-End Performance Statistics Disable Disable Maintain Table C-3. Sync Data Port Configuration Options 5 Cross Connect Configuration Options DTE-to-Network Assignment OptionsTable C-4. DTE-to-Network Assignment Options DTE01 DTE02 DTE03 DTE04 DTE05 DTE06 DTE07 DTE08 DTE24 Sync Data Port Assignment Options Table C-5. Sync Data Port Assignment Options 1 Table C-5. Sync Data Port Assignment Options 2 Table C-5. Sync Data Port Assignment Options 3 D01 D02 D03 D04 D05 D06 D07 D08 D24 General Configuration Options Table C-6. General Configuration Options 1 Table C-6. General Configuration Options 2 External Clock Rate KHz 1544 2048 1544 Table C-7. Communication Port Configuration Options 1 User Interface Configuration OptionsCommunication Port Configuration Options Table C-7. Communication Port Configuration Options 2 Table C-8. External Device Configuration Options 1 External Device Configuration OptionsTable C-7. Communication Port Configuration Options 3 Table C-8. External Device Configuration Options 2 Connect Prefix Text FieldConnect Indication String Text Field Escape Sequence Text Field Disconnect String Text Field Table C-8. External Device Configuration Options 3Escape Sequence Delay sec None None 0.2 0.4 0.6 0.8 Telnet Session Disable Enable Disable Telnet Sessions Configuration OptionsTable C-9. Telnet Sessions Configuration Options Ethernet 10BaseT Port Configuration Options Table C-10. Ethernet Port Configuration Options Alarm and Trap Configuration Options Table C-11. Alarm and Trap Configuration Options 1Ascii Alarm Messages Disable Disable Com Port Alarm & Trap Dial-Out Disable Enable Disable Table C-11. Alarm and Trap Configuration Options 2 Call Retry Disable Enable DisableDial Out Delay Time min 3 4 5 6 7 8 9 Alternate Dial-Out Directory None None 1 2 3 4 Management and Communication Configuration Options Communication Protocol Configuration OptionsTable C-12. Communication Protocol Configuration Options 1 Node IP Address Text Field Table C-12. Communication Protocol Configuration Options 2 PPP Slip General Snmp Management Configuration Options Table C-13. General Snmp Management Configuration Options Snmp NMS Security Configuration Options Table C-14. Snmp NMS Security Configuration Options Snmp Traps Configuration Options Table C-15. Snmp Traps Configuration Options 1Snmp Traps Disable Enable Disable Number of Trap Managers 1 1 2 3 4 5 Table C-15. Snmp Traps Configuration Options 2 General Traps Both Disable Warm AuthFail BothEnterprise Specific Traps Enable Enable Disable Link Traps Both Disable Up Down Both Table C-15. Snmp Traps Configuration Options 3 Link Trap Interfaces All Network DTE T1s Ports All DTE Interface Options Configuration WorksheetsNetwork Interface Options Sync Data Port Options Port Sync Data Port Options Port Network Interface Network Channel Allocation DTE Drop/Insert DSX-1 Interface DTE DSX-1 Channel Allocation DTE Signaling Assign N1 Voice RBS or Data Acami Sync Data Port OptionsChannel Disable , DTR General OptionsUser Interface Communication Port User Interface External Device Options Alarm and Trap Configuration Options User Interface Telnet Sessions OptionsUser Interface Ethernet Port Options Management and Communication Communication Protocol Options Snmp Traps Options Management and CommunicationSnmp NMS Security Options T1 Network Interface Table D-1. T1 Network Interface Connector Signal Pin NumberPin Assignments Figure D-1. T1 Line Interface Cable, RJ48C-to-RJ48C DTE Drop/Insert Interface Figure D-3. DTE Drop/Insert DSX-1 Cable 10BaseT Connector Use Pin # Table D-3. COM Port Connector Signal Direction Pin Number COM Port Interface Figure D-4. COM Port-to-PC Cable Pin P2 Serial Crossover CablePin EIA-530-A Port Interface Connector EIA-530-A-to-RS-449 Adapter Figure D-7. EIA-530-A-to-RS-449 Adapter Pin Assignments EIA-530-A-to-V.35 Adapter Figure D-8. EIA-530-A-to-V.35 Adapter Pin Assignments EIA-530-A-to-X.21 Adapter Direction Pin Number Table D-8. External Clock Connector Signal Pin Number External Clock Interface Group Snmp MIB ObjectsMIB II RFC System Group, MIB System Group sysServices Object system Interface Group, MIBSystem Group sysName Object system System Group sysLocation Object system Interface Group ifIndex Object ifEntry Interface Group ifDescr Object ifEntry Interface Group ifAdminStatus Object ifEntry Interface Group ifType Object ifEntryInterface Group ifMtu Object ifEntry Interface Group ifSpeed Object ifEntry Interface Group ifOperStatus Object ifEntry Interface Group ifLastChange Object ifEntry IP Group, MIB Interface Group Input Counters objects ifEntry 10 to ifEntry IP Group ipForwarding Object ip IP Group ipAddrTable Object ipIP Group ipAdEntAddr Object ipAddrEntry IP Group ipAdEntIfIndex Object ipAddrEntry IP Group ipRouteDest Object ipRouteEntry IP Group ipRouteIfIndex Object ipRouteEntry UDP Group, MIB Icmp Group, MIBTCP Group, MIB Snmp Group, MIB DS1/E1 MIB RFCTransmission Group, MIB Near End Group dsx1TimeElapsed Object dsx1ConfigEntry Near End Group dsx1ValidIntervals Object dsx1ConfigEntryNear End Group dsx1LineType Object dsx1ConfigEntry Near End Group dsx1LineCoding Object dsx1ConfigEntry Near End Group dsx1LoopbackConfig Object dsx1ConfigEntry Near End Group dsx1SendCode Object dsx1ConfigEntryNear End Group dsx1CircuitIdentifier Object dsx1ConfigEntry Near End Group dsx1LineStatus Object dsx1ConfigEntry Near End Group dsx1SignalMode Object dsx1ConfigEntry Near End Group dsx1Fdl Object dsx1ConfigEntry Near End Group The DS1 Total Table Objects dsx1TotalEntry Far End Group, DS1/E1 MIBDS1 Fractional Group, DS1/E1 MIB RS-232-like MIB RFC General Port Table, RS-232-like MIBNumber of Ports rs232Number Object rs232 General Port Table rs232PortIndex Object rs232PortEntry General Port Table rs232PortOutSpeed Object rs232PortEntry General Port Table rs232PortType Object rs232PortEntryGeneral Port Table rs232PortInSpeed Object rs232PortEntry Asynchronous Port Table, RS-232-like MIB Input Signal Table, RS-232-like MIB Input Signal Table rs232InSigName rs232InSigEntryInput Signal Table rs232InSigState rs232InSigEntry Input Signal Table rs232InSigChanges rs232InSigEntry Output Signal Table, RS-232-like MIB Output Signal Table rs232OutSigName rs232OutSigEntryOutput Signal Table rs232OutSigState rs232OutSigEntry Output Signal Table rs232OutSigChanges rs232OutSigEntry Generic Interface Test Table, Generic Interface MIB 3162-A2-GB20-40 August Enterprise MIB IP Network Addressing Scenario Standalone at the Central Site Network Local Carrier with Remote Standalone Figure F-2. Local Carrier with Remote Standalone Local and Remote Carriers Different Subnets Figure F-3. Local Carrier Connected to Remote Carriers Local and Remote Carriers Same Subnet Multiple NMSs Figure F-5. Multiple COM Ports Connected to Different NMSs Equipment Feature Number Equipment List Equipment List Glossary GL-1 GL-2 GL-3 GL-4 GL-5 GL-6 GL-7 GL-8 Index Numbers IN-2 Index IN-3 IN-4 IN-5