Chapter 3 Using the Operator Panel

KC-GL Pen Width

The KC-GL emulation mode enables you to set the pen widths in dots, for pen numbers 1 to 8, and the KC-GL page size.

1

 

Press the MENU key.

2

 

Press the

or

key repeatedly until Emulation

 

appears on the message display.

 

 

 

 

 

 

 

 

 

 

 

Emulation

 

 

 

 

 

 

PCL 6

 

 

 

3

 

If the current emulation is other than KC-GL, press

 

the ENTER key. A blinking question mark (?) ap-

 

 

 

 

pears.

 

 

 

 

 

 

 

 

 

 

 

 

Emulation

 

 

4

 

 

 

?PCL 6

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

pears.Press the

or

key repeatedly until KC-GLap-

 

 

 

 

 

 

 

 

 

 

 

 

Emulation

 

 

 

 

?KC-GL

 

 

 

5

 

Press the ENTER key.

 

 

 

 

 

 

 

 

 

 

Emulation

 

 

 

 

 

 

KC-GL

 

 

 

6

 

Press the

key to move to the >KC-GL Pen Width

 

submenu.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

>KC-GL

 

>

 

 

 

 

 

Pen Width

 

 

7

 

Press the

key.

 

 

 

 

 

 

 

 

 

 

 

 

>>Pen(1) Width

 

 

 

 

 

01 dot(s)

 

8

 

Press the

or

key repeatedly until the desired

 

pen number of 1 to 8 appears.

9

 

 

When the desired pen number is displayed, press the

 

ENTER key.

 

 

 

10

 

 

 

 

 

To change the pen width, press the key, then press

 

the ENTER key. A blinking cursor appears at the

 

 

width value.

>>Pen(1) Width 02dot(s)

 

 

Press the

or

key repeatedly until the desired pen

 

 

width in dots (00 to 99) appears. When the desired

 

 

pen width is displayed, press the ENTER key.

11

 

To set the KC-GL page size, press the key, then

 

press the

or

key until >KC-GL Page Set is

 

 

displayed.

 

 

 

12

 

To change the page size, press the ENTER key. A

 

blinking question mark (?) appears.

 

 

 

 

 

 

 

 

 

>KC-GL Page Set

 

 

 

 

 

 

 

 

 

? [SPSZ]

 

 

 

 

 

 

 

 

 

 

 

Press the 3 or 4 key repeatedly until the desired

 

 

page size (A2, A1, A0, B3, B2, B1, B0, and SPSZ)

 

 

appears. When selecting SPSZ, printing will be done

 

 

with the paper size specified by the PRESCRIBE

 

 

SPSZ command. For details, see Programming

 

 

Manual in the CD-ROM.

13

 

Press the ENTER key to set the page set you just se-

 

lected.

 

 

 

 

 

 

 

 

14 Press the MENU key. The display returns to Ready.

2.2.6 Setting the Default Font

You can select the default font for the current interface. In addition to the internal fonts, all fonts that are downloaded to the printer memory, or fonts stored on a memory card, hard disk, or option ROM, can be selected as the default font.

In this menu, you can also set the type and pitch for Courier and Letter Gothic; as well as print a font list.

Selecting the Default Font

1

Press the MENU key.

2

pears.Press the

or key repeatedly until Font > ap-

 

 

 

 

 

 

 

 

Font

>

 

 

 

 

 

3-24