Chapter 3 Using the Operator Panel

1

 

Press the MENU key.

2

 

Press the

or

key repeatedly until Paper

 

Handling > appears.

 

 

 

 

 

 

 

 

 

 

Paper Handling >

 

3

 

 

 

 

 

 

 

 

Press the

key.

 

 

4

 

Press the

or

key repeatedly until >Duplex

 

Mode appears.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

>Duplex Mode

 

 

 

 

 

 

None

 

 

 

5

 

Press the ENTER key. A blinking question mark (?)

 

appears.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

>Duplex Mode

 

 

6

 

 

 

?None

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Press the

or

key to display the desired duplex

 

mode. The display changes as shown below.

 

 

 

 

None (default)

 

 

 

 

Short edge bind

 

 

Long edge bind

 

 

7

 

When the desired duplex mode is displayed, press

 

the ENTER key.

 

 

8

 

 

 

 

Press the MENU key. The message display returns to

 

Ready.

 

 

 

 

 

 

 

 

Selecting the Output Device

You can select whether printouts will be received by the printer’s top tray (face-down) or to the optional document finisher’s output tray.

1

 

Press the MENU key.

 

 

2

 

Press the

or

key repeatedly until Paper

 

Handling > appears.

 

 

 

 

 

 

 

 

 

 

 

 

Paper Handling >

 

3

 

 

 

 

 

 

Press the

key.

 

 

4

 

Press the

or

key repeatedly until >Stack

 

Select appears.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

>Stack Select

 

 

 

 

 

 

Top tray FaceDn

 

5

 

Press the ENTER key. A blinking question mark (?)

 

appears. The selected output device will be displayed.

 

 

 

 

 

 

 

 

 

 

 

>Stack Select

 

 

6

 

 

 

?Top tray FaceDn

 

 

 

 

 

 

 

 

 

 

 

 

Press the

or key to display the desired destina-

 

tion. The output tray changes as shown below.

 

 

 

 

Top tray FaceDn

 

 

 

 

Finisher FaceUp (when document finisher is

 

 

Finisher FaceDn

equipped)

 

 

(when document finisher is

 

 

 

 

 

 

equipped)

7

 

When the desired paper source displayed, press the

 

ENTER key.

 

 

 

8

 

 

 

 

 

Press the MENU key. The message display returns

 

to Ready.

 

 

 

 

 

 

 

 

Adjusting the Stitch Positions

When installing the option document finisher DF-75, adjust the stitch positions using the following procedures. In the default settings, the stitch position is set in the center of the paper. Depending on the paper, a certain amount of deviation will occur. In this case, also use this menu to adjust the stitch position.

The adjustment can be done by moving the stitch position adjustment gear in the document finisher.

For example, select the range from -57 to +57 (1 = approximately 0.14 mm) to move the stitch position approximately 8

mmas shown in the following figure. The default setting is

000 (center of the paper.)

Default stitch position (center of the paper)

Feed direction

+57

-57

(Approx. 8 mm)

(Approx. 8 mm)

Figure 3-21

 

3-45