Manuals / Intel / Computer Equipment / Switch

Intel 410 manual EK–SMRAC–IG.C01

Models: 410

1 60

Download 60 pages 35.31 Kb

Page 20

Manual background

Getting Started - RAID Array 410 for Windows NT – Intel

3.Apply power to the controller, by using the power switch on the AC Power Entry Control- ler. You should hear a momentary audible tone (beep), and see the indicator LEDs illumi- nate. In addition, the controller reset button (see Figure 1–4) contains a green LED, which should flash at approximately 1 Hz. For additional information, refer to the SWXRC RAID Array Controller User’s Guide (EK-SMCS1-UG) and the SWXSC-AA Office Expansion RAID Enclosure User’s Guide (EK-SMCPD-UG), included with these systems.

Power on the RAID Controller. The batteries should be fully recharged within six hours.

NOTE

As an alternative to waiting six hours, you may proceed now with the installation and getting started steps described in subsequent chapters of this manual. Then, when you perform the steps de- scribed in Chapter 4, Installing and Using the RAID Array 410 Manager for Windows NT, you will be able to check the status of the batteries. This is described in Section 4.4, Setting Controller Communications. If the battery status shows “good,” you may then continue, and create your configuration.

1–8	EK–SMRAC–IG. C01

Image 20

Intel 410 manual EK–SMRAC–IG.C01

Contents

Installation Guide Getting StartedRAID Array 410 for Windows NT – Intel Order Number: EK–SMRAC-IG.C01Third Edition, June Contents Appendix A Configuration Records – Blank Forms FiguresDate Revision RecordRevision Level Page About This Guide Chapter 2: Host Adapter InstallationAudience Document StructureAppendix A: Configuration Record Associated DocumentsConventions viii6.Creating an Initial Configuration Chapter Perform a System Backup Installation “Checklist”Pre-installationSteps ∙The associated system hardware manuals Page 1.1Site Preparation 1.2Unpacking the RAID Array 410 SWXRA-Yx 1.3Removing the RAID Array 410 from the PalletFigure 1–3Installation of Ramp on Shipping Pallet Figure 1–2Unpacking the RAID Array1.4Placing the RAID Array 410 Enclosure 1.6.1 PC Program Card Handling Precautions 1.6.2 Installing PC Program Card in Controller1.7Connecting the Controller to Computer Figure 1–4PC Program Card Slot LocationPage EK–SMRAC–IG.C01 Page Page Host Adapter Installation – Intel-basedSystem 2.1Install the Host Adapter2.1.1 Preparing to Install the Host Adapter 2.1.2 Installing the Host Adapter2.2Installing the Subsystem Figure 2–1Connecting SCSI CableEK–SMRAC–IG.C01 2.3Configuration Utilities 2.4.1 Windows NT Not Installed on System2.4.2 Windows NT Previously Installed Congratulations Page 3.1RAID Manager for Windows NT 3.3Installing the RAID Manager Software 3.4Setting Controller Communications3.5Setting the Controller Configuration Click on OK after making the above selections NOTES 3.6Creating an Initial Configuration3.6.1 Displaying Physical/Logical View of System 6.Choose Modify from the choices listed 3.6.2 Practice Example: Creating a Single Disk 3.6.3 Practice Example: Creating a Stripeset 3.6.4 Practice Example: Creating a Mirrorset 3.6.5 Practice Example: Adding a Spare Disk Congratulations 3.6.6 Practice Example: Deleting Storagesets3.7Saving the RAID Configuration Date__________________ Name of RAIDsetType of RAIDset TargetPage 4.1Completing Configurations under Windows NT 4.1.1 Verifying that hszdisk.sys Loaded4.1.2 Completing a New RAID Array Configuration 2.Select Administrative Tools3.Select Disk Administrator 1.Select Program ManagerUnderstanding the Disk Administrator Display Figure 4–3Disk Administrator Screen DisplayBefore proceeding, you should verify the following 3.Optional: Make disk logical names permanent EK–SMRAC–IG.C01 Figure 4–6Tools Pull-DownChoices4.1.3Changes to RAID Array Configuration EK–SMRAC–IG.C01 Configuration Records – Blank Forms Date__________________ Name of RAIDset Type of RAIDsetTarget Disks UsedAppendix A. Configuration Records – Blank Forms Date__________________Name of RAIDset Type of RAIDset TargetDate__________________ Name of RAIDset Type of RAIDsetTarget Disks UsedB.2 Accessing the CLI Accessing the Command Line Interpreter CLIB.1 What is the CLI? 3.Set the communications parameters to Reader’s Comments Most-LikedFeatures Least-LikedFeaturesManual Order Number Manual Rating