Manuals / Intel / Computer Equipment / Switch

Intel 410 manual 4.1Completing Configurations under Windows NT, Verifying that hszdisk.sys Loaded

Models: 410

1 60

Download 60 pages 35.31 Kb

Page 45

4.1Completing Configurations under Windows NT

4

Completing your Configuration Setup under Windows NT

This chapter contains instructions for how to complete your configuration set up through Disk Administrator under Windows NT.

4.1Completing Configurations under Windows NT

In order for Windows NT to recognize new RAID Array 410 devices or changes to existing configurations, you must reboot your system to restart Windows NT.

4.1.1 Verifying that hszdisk.sys Loaded

Prior to running Disk Administrator, verify that hszdisk recognizes the devices that you cre- ated in the RAID Array 410 Subsystem.

To verify hszdisk, follow these steps:

1.Find the Event Viewer in the Administrative Tools group and open it. Look for an entry for hszdisk in the Event Viewer window.

If no entry for the hszdisk appears in the Event View window, go to Chapter 2 of this guide and reinstall hszdisk.

If an entry for hszdisk appears with 0 in the Event column, similar to the screen shown in Figure 4−1, the hszdisk loaded successfully and connected to at least one logical drive in the RAID Array 410. Go on to Section 4.1.3 to complete the new array configuration.

Figure 4−1 How The hszdisk Entry Appears When It Loads Successfully.

EK–SMRAC–IG. C01

4–1

Image 45

Intel 410 manual 4.1Completing Configurations under Windows NT, Verifying that hszdisk.sys Loaded

Contents

Getting Started Installation GuideRAID Array 410 for Windows NT – Intel Order Number: EK–SMRAC-IG.C01Third Edition, June Contents Figures Appendix A Configuration Records – Blank FormsRevision Record Revision LevelDate Page Chapter 2: Host Adapter Installation About This GuideAudience Document StructureAssociated Documents Appendix A: Configuration RecordConventions viii6.Creating an Initial Configuration Chapter Installation “Checklist” Pre-installationStepsPerform a System Backup ∙The associated system hardware manuals Page 1.1Site Preparation 1.3Removing the RAID Array 410 from the Pallet 1.2Unpacking the RAID Array 410 SWXRA-YxFigure 1–2Unpacking the RAID Array Figure 1–3Installation of Ramp on Shipping Pallet1.4Placing the RAID Array 410 Enclosure 1.6.2 Installing PC Program Card in Controller 1.6.1 PC Program Card Handling PrecautionsFigure 1–4PC Program Card Slot Location 1.7Connecting the Controller to ComputerPage EK–SMRAC–IG.C01 Page Page 2.1Install the Host Adapter Host Adapter Installation – Intel-basedSystem2.1.2 Installing the Host Adapter 2.1.1 Preparing to Install the Host AdapterFigure 2–1Connecting SCSI Cable 2.2Installing the SubsystemEK–SMRAC–IG.C01 2.4.1 Windows NT Not Installed on System 2.3Configuration Utilities2.4.2 Windows NT Previously Installed Congratulations Page 3.1RAID Manager for Windows NT 3.4Setting Controller Communications 3.3Installing the RAID Manager Software3.5Setting the Controller Configuration Click on OK after making the above selections 3.6Creating an Initial Configuration 3.6.1 Displaying Physical/Logical View of SystemNOTES 6.Choose Modify from the choices listed 3.6.2 Practice Example: Creating a Single Disk 3.6.3 Practice Example: Creating a Stripeset 3.6.4 Practice Example: Creating a Mirrorset 3.6.5 Practice Example: Adding a Spare Disk 3.6.6 Practice Example: Deleting Storagesets Congratulations3.7Saving the RAID Configuration Name of RAIDset Date__________________Type of RAIDset TargetPage 4.1.1 Verifying that hszdisk.sys Loaded 4.1Completing Configurations under Windows NT2.Select Administrative Tools 4.1.2 Completing a New RAID Array Configuration3.Select Disk Administrator 1.Select Program ManagerFigure 4–3Disk Administrator Screen Display Understanding the Disk Administrator DisplayBefore proceeding, you should verify the following 3.Optional: Make disk logical names permanent Figure 4–6Tools Pull-DownChoices EK–SMRAC–IG.C014.1.3Changes to RAID Array Configuration EK–SMRAC–IG.C01 Configuration Records – Blank Forms Name of RAIDset Type of RAIDset Date__________________Target Disks UsedDate__________________ Appendix A. Configuration Records – Blank FormsName of RAIDset Type of RAIDset TargetName of RAIDset Type of RAIDset Date__________________Target Disks UsedAccessing the Command Line Interpreter CLI B.1 What is the CLI?B.2 Accessing the CLI 3.Set the communications parameters to Most-LikedFeatures Least-LikedFeatures Reader’s CommentsManual Order Number Manual Rating