Manuals / Intel / Computer Equipment / Switch

Intel 410 manual Click on OK after making the above selections

Models: 410

1 60

Download 60 pages 35.31 Kb

Page 34

Click on OK after making the above selections.

Getting Started - RAID Array 410 for Windows NT – Intel

Select the choice, “ D” for Host Functionality; this sets the controller to operate in Win- dows NT mode. This choice is required for the controller to operate correctly with Win- dows NT. Refer to the release notes for this product for more information.

∙Go to the bottom of the window and enter a value of 5 for the Cache Flush Timer/Timers.

NOTE

It is mandatory that you select choice “D” for Host Functionality for the SWXRC-04 controller to operate correctly with Windows NT. It is also mandatory that the Cache Flush Timer/Timers be set to 5.

Click on OK after making the above selections.

Figure 3–3 Controller Configuration Window

At this point, your initial set up procedure is complete. You may now configure your system using the RAID Manager graphical user interface. The RAID Manager graphical user inter- face facilitates the configuration process for you.

NOTE

You may not be able to create RAIDsets or mirrorsets if the write- back cache batteries are not fully charged.

To check controller battery status, click on the Controller button at the left of the window. Doing so brings up the Controller Status display, which includes the battery status. When the battery status shows “good,” you may continue and create your initial configura- tion.

3–4	EK–SMRAC–IG. C01

Image 34

Intel 410 manual Click on OK after making the above selections

Contents

RAID Array 410 for Windows NT – Intel Installation GuideGetting Started Order Number: EK–SMRAC-IG.C01Third Edition, June Contents Appendix A Configuration Records – Blank Forms FiguresRevision Level Revision RecordDate Page Audience About This GuideChapter 2: Host Adapter Installation Document StructureConventions Appendix A: Configuration RecordAssociated Documents viii6.Creating an Initial Configuration Chapter Pre-installationSteps Installation “Checklist”Perform a System Backup ∙The associated system hardware manuals Page 1.1Site Preparation 1.2Unpacking the RAID Array 410 SWXRA-Yx 1.3Removing the RAID Array 410 from the PalletFigure 1–3Installation of Ramp on Shipping Pallet Figure 1–2Unpacking the RAID Array1.4Placing the RAID Array 410 Enclosure 1.6.1 PC Program Card Handling Precautions 1.6.2 Installing PC Program Card in Controller1.7Connecting the Controller to Computer Figure 1–4PC Program Card Slot LocationPage EK–SMRAC–IG.C01 Page Page Host Adapter Installation – Intel-basedSystem 2.1Install the Host Adapter2.1.1 Preparing to Install the Host Adapter 2.1.2 Installing the Host Adapter2.2Installing the Subsystem Figure 2–1Connecting SCSI CableEK–SMRAC–IG.C01 2.3Configuration Utilities 2.4.1 Windows NT Not Installed on System2.4.2 Windows NT Previously Installed Congratulations Page 3.1RAID Manager for Windows NT 3.3Installing the RAID Manager Software 3.4Setting Controller Communications3.5Setting the Controller Configuration Click on OK after making the above selections 3.6.1 Displaying Physical/Logical View of System 3.6Creating an Initial ConfigurationNOTES 6.Choose Modify from the choices listed 3.6.2 Practice Example: Creating a Single Disk 3.6.3 Practice Example: Creating a Stripeset 3.6.4 Practice Example: Creating a Mirrorset 3.6.5 Practice Example: Adding a Spare Disk Congratulations 3.6.6 Practice Example: Deleting Storagesets3.7Saving the RAID Configuration Type of RAIDset Date__________________Name of RAIDset TargetPage 4.1Completing Configurations under Windows NT 4.1.1 Verifying that hszdisk.sys Loaded3.Select Disk Administrator 4.1.2 Completing a New RAID Array Configuration2.Select Administrative Tools 1.Select Program ManagerUnderstanding the Disk Administrator Display Figure 4–3Disk Administrator Screen DisplayBefore proceeding, you should verify the following 3.Optional: Make disk logical names permanent EK–SMRAC–IG.C01 Figure 4–6Tools Pull-DownChoices4.1.3Changes to RAID Array Configuration EK–SMRAC–IG.C01 Configuration Records – Blank Forms Target Date__________________Name of RAIDset Type of RAIDset Disks UsedName of RAIDset Type of RAIDset Appendix A. Configuration Records – Blank FormsDate__________________ TargetTarget Date__________________Name of RAIDset Type of RAIDset Disks UsedB.1 What is the CLI? Accessing the Command Line Interpreter CLIB.2 Accessing the CLI 3.Set the communications parameters to Manual Order Number Reader’s CommentsMost-LikedFeatures Least-LikedFeatures Manual Rating