Manuals / Intel / Computer Equipment / Switch

Intel 410 manual Configuration Records – Blank Forms

Models: 410

1 60

Download 60 pages 35.31 Kb

Page 53

Configuration Records – Blank Forms

A

Configuration Records – Blank Forms

This contains copies of the table used in Chapter 3 to record the configuration of your system. If addi- tional copies are required, these tables can be reproduced as necessary.

EK–SMRAC–IG. C01

A–1

Image 53

Intel 410 manual Configuration Records – Blank Forms

Contents

Getting Started Installation GuideRAID Array 410 for Windows NT – Intel Order Number: EK–SMRAC-IG.C01Third Edition, June Contents Figures Appendix A Configuration Records – Blank FormsDate Revision RecordRevision Level Page Chapter 2: Host Adapter Installation About This GuideAudience Document StructureAssociated Documents Appendix A: Configuration RecordConventions viii6.Creating an Initial Configuration Chapter Perform a System Backup Installation “Checklist”Pre-installationSteps ∙The associated system hardware manuals Page 1.1Site Preparation 1.3Removing the RAID Array 410 from the Pallet 1.2Unpacking the RAID Array 410 SWXRA-YxFigure 1–2Unpacking the RAID Array Figure 1–3Installation of Ramp on Shipping Pallet1.4Placing the RAID Array 410 Enclosure 1.6.2 Installing PC Program Card in Controller 1.6.1 PC Program Card Handling PrecautionsFigure 1–4PC Program Card Slot Location 1.7Connecting the Controller to ComputerPage EK–SMRAC–IG.C01 Page Page 2.1Install the Host Adapter Host Adapter Installation – Intel-basedSystem2.1.2 Installing the Host Adapter 2.1.1 Preparing to Install the Host AdapterFigure 2–1Connecting SCSI Cable 2.2Installing the SubsystemEK–SMRAC–IG.C01 2.4.1 Windows NT Not Installed on System 2.3Configuration Utilities2.4.2 Windows NT Previously Installed Congratulations Page 3.1RAID Manager for Windows NT 3.4Setting Controller Communications 3.3Installing the RAID Manager Software3.5Setting the Controller Configuration Click on OK after making the above selections NOTES 3.6Creating an Initial Configuration3.6.1 Displaying Physical/Logical View of System 6.Choose Modify from the choices listed 3.6.2 Practice Example: Creating a Single Disk 3.6.3 Practice Example: Creating a Stripeset 3.6.4 Practice Example: Creating a Mirrorset 3.6.5 Practice Example: Adding a Spare Disk 3.6.6 Practice Example: Deleting Storagesets Congratulations3.7Saving the RAID Configuration Name of RAIDset Date__________________Type of RAIDset TargetPage 4.1.1 Verifying that hszdisk.sys Loaded 4.1Completing Configurations under Windows NT2.Select Administrative Tools 4.1.2 Completing a New RAID Array Configuration3.Select Disk Administrator 1.Select Program ManagerFigure 4–3Disk Administrator Screen Display Understanding the Disk Administrator DisplayBefore proceeding, you should verify the following 3.Optional: Make disk logical names permanent Figure 4–6Tools Pull-DownChoices EK–SMRAC–IG.C014.1.3Changes to RAID Array Configuration EK–SMRAC–IG.C01 Configuration Records – Blank Forms Name of RAIDset Type of RAIDset Date__________________Target Disks UsedDate__________________ Appendix A. Configuration Records – Blank FormsName of RAIDset Type of RAIDset TargetName of RAIDset Type of RAIDset Date__________________Target Disks UsedB.2 Accessing the CLI Accessing the Command Line Interpreter CLIB.1 What is the CLI? 3.Set the communications parameters to Most-LikedFeatures Least-LikedFeatures Reader’s CommentsManual Order Number Manual Rating