Manuals / Intel / Computer Equipment / Switch

Intel 410 manual EK–SMRAC–IG.C01

Models: 410

1 60

Download 60 pages 35.31 Kb

Page 26

Manual background

Getting Started - RAID Array 410 for Windows NT – Intel

Secure the SCSI cable to the trilink on the controller by tightening the two screws on the cable connector.

Figure 2–2 SCSI Cable Connection to Controller (Single Controller)

Figure 2–3 SCSI Cable Connection to Controller (Dual Controller)

2–4	EK–SMRAC–IG. C01

Image 26

Intel 410 manual EK–SMRAC–IG.C01

Contents

RAID Array 410 for Windows NT – Intel Installation GuideGetting Started Order Number: EK–SMRAC-IG.C01Third Edition, June Contents Appendix A Configuration Records – Blank Forms FiguresDate Revision RecordRevision Level Page Audience About This GuideChapter 2: Host Adapter Installation Document StructureConventions Appendix A: Configuration RecordAssociated Documents viii6.Creating an Initial Configuration Chapter Perform a System Backup Installation “Checklist”Pre-installationSteps ∙The associated system hardware manuals Page 1.1Site Preparation 1.2Unpacking the RAID Array 410 SWXRA-Yx 1.3Removing the RAID Array 410 from the PalletFigure 1–3Installation of Ramp on Shipping Pallet Figure 1–2Unpacking the RAID Array1.4Placing the RAID Array 410 Enclosure 1.6.1 PC Program Card Handling Precautions 1.6.2 Installing PC Program Card in Controller1.7Connecting the Controller to Computer Figure 1–4PC Program Card Slot LocationPage EK–SMRAC–IG.C01 Page Page Host Adapter Installation – Intel-basedSystem 2.1Install the Host Adapter2.1.1 Preparing to Install the Host Adapter 2.1.2 Installing the Host Adapter2.2Installing the Subsystem Figure 2–1Connecting SCSI CableEK–SMRAC–IG.C01 2.3Configuration Utilities 2.4.1 Windows NT Not Installed on System2.4.2 Windows NT Previously Installed Congratulations Page 3.1RAID Manager for Windows NT 3.3Installing the RAID Manager Software 3.4Setting Controller Communications3.5Setting the Controller Configuration Click on OK after making the above selections NOTES 3.6Creating an Initial Configuration3.6.1 Displaying Physical/Logical View of System 6.Choose Modify from the choices listed 3.6.2 Practice Example: Creating a Single Disk 3.6.3 Practice Example: Creating a Stripeset 3.6.4 Practice Example: Creating a Mirrorset 3.6.5 Practice Example: Adding a Spare Disk Congratulations 3.6.6 Practice Example: Deleting Storagesets3.7Saving the RAID Configuration Type of RAIDset Date__________________Name of RAIDset TargetPage 4.1Completing Configurations under Windows NT 4.1.1 Verifying that hszdisk.sys Loaded3.Select Disk Administrator 4.1.2 Completing a New RAID Array Configuration2.Select Administrative Tools 1.Select Program ManagerUnderstanding the Disk Administrator Display Figure 4–3Disk Administrator Screen DisplayBefore proceeding, you should verify the following 3.Optional: Make disk logical names permanent EK–SMRAC–IG.C01 Figure 4–6Tools Pull-DownChoices4.1.3Changes to RAID Array Configuration EK–SMRAC–IG.C01 Configuration Records – Blank Forms Target Date__________________Name of RAIDset Type of RAIDset Disks UsedName of RAIDset Type of RAIDset Appendix A. Configuration Records – Blank FormsDate__________________ TargetTarget Date__________________Name of RAIDset Type of RAIDset Disks UsedB.2 Accessing the CLI Accessing the Command Line Interpreter CLIB.1 What is the CLI? 3.Set the communications parameters to Manual Order Number Reader’s CommentsMost-LikedFeatures Least-LikedFeatures Manual Rating