Manuals / Intel / Computer Equipment / Switch

Intel 410 manual 2.2Installing the Subsystem, 1Connecting SCSI Cable

Models: 410

1 60

Download 60 pages 35.31 Kb

Page 25

Figure 2–1 Connecting SCSI Cable

Chapter 2. Host Adapter Installation – Intel-Based System

Connect the SCSI cable to the host adapter as shown in Figure 3–1.

3.The adapter is now physically installed. Later in the installation process, you will power on your system and load the appropriate software for the required host adapter drivers.

Figure 2–1 Connecting SCSI Cable

2.2Installing the Subsystem

1.Unlock the RAID Array Enclosure, if necessary, using the keys provided, and open the enclosure front door.

2.Turn off AC power to the enclosure.

3.Install the SCSI cable between the host system and the RAID Controller.

∙Route the right angle connector end of the cable under the SWXRA-Yx Subsystem enclosure and up through the front access hole closest to the connector on the RAID controller.

∙Install the connector with the cable dressed to the right by firmly pushing it onto the mating connector on the controller’s trilink connector. For a single controller configu- ration (see Figure 3–2), the other side of the trilink contains a terminator. For dual controller configurations, one trilink contains a terminator and is connected to the trilink on the other controller (see Figure 3–3) through an interconnecting SCSI cable (BN21L-0B).

EK–SMRAC–IG. C01

2–3

Image 25

Intel 410 manual 2.2Installing the Subsystem, 1Connecting SCSI Cable

Contents

Getting Started Installation GuideRAID Array 410 for Windows NT – Intel Order Number: EK–SMRAC-IG.C01Third Edition, June Contents Figures Appendix A Configuration Records – Blank FormsRevision Level Revision RecordDate Page Chapter 2: Host Adapter Installation About This GuideAudience Document StructureAssociated Documents Appendix A: Configuration RecordConventions viii6.Creating an Initial Configuration Chapter Pre-installationSteps Installation “Checklist”Perform a System Backup ∙The associated system hardware manuals Page 1.1Site Preparation 1.3Removing the RAID Array 410 from the Pallet 1.2Unpacking the RAID Array 410 SWXRA-YxFigure 1–2Unpacking the RAID Array Figure 1–3Installation of Ramp on Shipping Pallet1.4Placing the RAID Array 410 Enclosure 1.6.2 Installing PC Program Card in Controller 1.6.1 PC Program Card Handling PrecautionsFigure 1–4PC Program Card Slot Location 1.7Connecting the Controller to ComputerPage EK–SMRAC–IG.C01 Page Page 2.1Install the Host Adapter Host Adapter Installation – Intel-basedSystem2.1.2 Installing the Host Adapter 2.1.1 Preparing to Install the Host AdapterFigure 2–1Connecting SCSI Cable 2.2Installing the SubsystemEK–SMRAC–IG.C01 2.4.1 Windows NT Not Installed on System 2.3Configuration Utilities2.4.2 Windows NT Previously Installed Congratulations Page 3.1RAID Manager for Windows NT 3.4Setting Controller Communications 3.3Installing the RAID Manager Software3.5Setting the Controller Configuration Click on OK after making the above selections 3.6.1 Displaying Physical/Logical View of System 3.6Creating an Initial ConfigurationNOTES 6.Choose Modify from the choices listed 3.6.2 Practice Example: Creating a Single Disk 3.6.3 Practice Example: Creating a Stripeset 3.6.4 Practice Example: Creating a Mirrorset 3.6.5 Practice Example: Adding a Spare Disk 3.6.6 Practice Example: Deleting Storagesets Congratulations3.7Saving the RAID Configuration Name of RAIDset Date__________________Type of RAIDset TargetPage 4.1.1 Verifying that hszdisk.sys Loaded 4.1Completing Configurations under Windows NT2.Select Administrative Tools 4.1.2 Completing a New RAID Array Configuration3.Select Disk Administrator 1.Select Program ManagerFigure 4–3Disk Administrator Screen Display Understanding the Disk Administrator DisplayBefore proceeding, you should verify the following 3.Optional: Make disk logical names permanent Figure 4–6Tools Pull-DownChoices EK–SMRAC–IG.C014.1.3Changes to RAID Array Configuration EK–SMRAC–IG.C01 Configuration Records – Blank Forms Name of RAIDset Type of RAIDset Date__________________Target Disks UsedDate__________________ Appendix A. Configuration Records – Blank FormsName of RAIDset Type of RAIDset TargetName of RAIDset Type of RAIDset Date__________________Target Disks UsedB.1 What is the CLI? Accessing the Command Line Interpreter CLIB.2 Accessing the CLI 3.Set the communications parameters to Most-LikedFeatures Least-LikedFeatures Reader’s CommentsManual Order Number Manual Rating